Steering

Steering is the control of the direction of locomotion.[2]

The direction of motion of a bicycle is chiefly controlled with the handlebar which turns the direction of the front wheel, steering the bicycle. Steering can also be achieved by leaning the bicycle.[1]
Part of a car steering mechanism: tie rod, steering arm, king pin axis (using ball joints)

A conventional automotive steering arrangement allows a driver to control the direction of the vehicle by turning the direction of the front wheels using a hand–operated steering wheel positioned in front of the driver. The steering wheel is attached to a steering column, which is linked to rods, pivots and gears that allow the driver to change the direction of the front wheels. Other arrangements are sometimes found on different types of vehicles; for example, a tiller or rear-wheel steering. Tracked vehicles such as bulldozers and tanks usually employ differential steering, where the tracks are made to move at different speeds or even in opposite directions, using the clutch and brakes, to achieve a change of direction.

Aircraft flight control systems are normally steered when airborne by the use of ailerons, spoilerons, or both to bank the aircraft into a turn; although the rudder can also be used to turn the aircraft, it is usually used to minimize adverse yaw, rather than as a means to directly cause the turn. On the ground, aircraft are generally steered at low speeds by turning the nosewheel or tailwheel (using a tiller or the rudder pedals) or through differential braking, and by the rudder at high speeds. Missiles, airships and large hovercraft are usually steered by a rudder, thrust vectoring, or both. Small sport hovercraft have similar rudders, but steer mostly by the pilot shifting their weight from side to side and unbalancing the more powerful lift forces beneath the skirt. Jet packs and flying platforms are steered by thrust vectoring only.

Helicopter flight controls are steered by cyclic control, changing the thrust vector of the main rotor(s), and by anti-torque control, usually provided by a tail rotor.

Ships and boats are usually steered with a rudder. Depending on the size of the vessel, rudders can be manually actuated, or operated using a servomechanism, or a trim tab or servo tab system. Boats using outboard motors steer by rotating the entire drive unit. Boats with inboard motors sometimes steer by rotating the propeller pod only (i.e. Volvo Penta IPS drive). Modern ships with diesel-electric drive use azimuth thrusters. Boats powered by oars or paddles are steered by generating a higher propulsion force on the side of the boat opposite of the direction of turn. Jet skis are steered by weight-shift induced roll and water jet thrust vectoring.

The rudder of a vessel can steer the ship only when water is passing over it. Hence, when a ship is not moving relative to the water it is in or cannot move its rudder, it does not respond to the helm and is said to have "lost steerage". The motion of a ship through the water is known as "making way". Boats on rivers must always be under propulsion, even when traveling downstream, in order to move moving fast enough through the water so they turn in response to the helm. This is called having "steerage way".[3]

Automotive

Geometry

Ackermann steering geometry

The basic aim of steering is to ensure that the wheels are pointing in the desired directions to move the vehicle as required. This is typically achieved by a series of linkages, rods, pivots and gears. One of the fundamental concepts is that of caster angle. Each wheel is steered with a pivot point ahead of the wheel, which tends to make the steering self-centering towards the direction of travel.

The steering linkages connecting the steering box and the wheels usually conform to a variation of Ackermann steering geometry, to account for the fact that in a turn, the inner wheel travels a path of smaller radius than the outer wheel, so that the degree of toe suitable for driving in a straight path is not suitable for turns. The angle the wheels make with the vertical plane, known as camber angle, also influences steering dynamics as do the tires.

Rack and pinion, recirculating ball, worm and sector

Rack and pinion unit mounted in the cockpit of an Ariel Atom sports car chassis, atypical of contemporary production automobiles
Non-assisted steering box of a motor vehicle

Many modern cars have a steering mechanism called a rack and pinion. The steering wheel turns a pinion gear, which moves a rack back and forth to steer the wheels. This mechanism converts the circular motion of the steering wheel to linear motion, which is applied to the wheels of the car via tie rods and a steering knuckle.

Rack and pinion steering has several advantages, such as a direct steering "feel". This means that the driver can feel the road better and have more precise control over the car's movement.

BMW was one of the first manufacturers to adopt rack and pinion steering systems in the 1930s, with many other European manufacturers following suit. American automakers began using rack and pinion steering in the 1974 Ford Pinto.[4]

Older designs use two main principles: the worm and sector design and the screw and nut. Both types were enhanced by reducing the friction; for screw and nut it is the recirculating ball mechanism, which is still found on trucks and utility vehicles. The steering column turns a large screw, which meshes with the nut by recirculating balls. The nut moves a sector of a gear, causing it to rotate about its axis as the screw is turned; an arm attached to the axis of the sector moves the pitman arm, which is connected to the steering linkage and thus steers the wheels. The recirculating ball version of this apparatus reduces the considerable friction by placing large ball bearings between the screw and the nut. At either end of the apparatus, the balls exit from between the two pieces into a channel internal to the box, which connects them with the other end of the apparatus. Thus, they are "recirculated".

The recirculating ball mechanism has the advantage of a much greater mechanical advantage, so that it was found on larger, heavier vehicles while the rack and pinion was originally limited to smaller and lighter ones; due to the almost universal adoption of power steering, however, this is no longer an important advantage, leading to the increasing use of rack and pinion on newer cars. The recirculating ball design also has a perceptible lash, or "dead spot" on center, where a minute turn of the steering wheel in either direction does not move the steering apparatus; this is easily adjustable via a screw on the end of the steering box to account for wear, but it cannot be eliminated because it will produce excessive internal forces at other positions and the mechanism will wear very rapidly. This design is still in use in trucks and other large vehicles, where rapidity of steering and direct feel are less important than robustness, maintainability, and mechanical advantage.

The worm and sector was an older design, used for example in Willys and Chrysler vehicles, and the Ford Falcon (1960s). To reduce friction, the sector is replaced by a roller or rotating pins on the rocker shaft arm.

Generally, older vehicles use the recirculating ball mechanism, and only newer vehicles use rack-and-pinion steering. This division is not very strict, however, and rack-and-pinion steering systems can be found on British sports cars of the mid-1950s, and some German carmakers did not give up recirculating ball technology until the early 1990s.

Other systems for steering exist, but are uncommon on road vehicles. Children's toys and go-karts often use a very direct linkage in the form of a bellcrank (also commonly known as a pitman arm) attached directly between the steering column and the steering arms, and the use of cable-operated steering linkages (e.g. the capstan and bowstring mechanism) is also found on some home-built vehicles such as soapbox cars and recumbent tricycles.

Power steering

Power steering helps the driver of a vehicle to steer by directing some of its engine power to assist in swiveling the steered road wheels about their steering axes. As vehicles have become heavier and switched to front-wheel drive, particularly using negative offset geometry, along with increases in tire width and diameter, the effort needed to turn the wheels about their steering axis has increased, often to the point where major physical exertion would be needed were it not for power assistance. To alleviate this, auto makers have developed power steering systems, or more correctly power-assisted steering, since on road-going vehicles there has to be a mechanical linkage as a fail-safe. There are two types of power steering systems: hydraulic and electric/electronic. A hydraulic-electric hybrid system is also possible.

A hydraulic power steering (HPS) uses hydraulic pressure supplied by an engine-driven pump to assist the motion of turning the steering wheel. Electric power steering (EPS) is more efficient than hydraulic power-steering, since the electric power-steering motor only needs to provide assistance when the steering wheel is turned, whereas the hydraulic pump must run constantly. In EPS, the amount of assistance is easily tunable to the vehicle type, road speed, and driver preference. An added benefit is the elimination of the environmental hazard posed by leakage and disposal of hydraulic power-steering fluid. In addition, electrical assistance is not lost when the engine fails or stalls, whereas hydraulic assistance stops working if the engine stops, making the steering doubly heavy as the driver must now turn not only the very heavy steering—without any help—but also the power-assistance system itself.

Speed-sensitive steering

Speed-dependent four-wheel steering.

A development of power steering is speed-sensitive steering, where the steering is heavily assisted at low speed and lightly assisted at high speed. Auto makers perceive that motorists might need to make large steering inputs while maneuvering for parking, but not while traveling at high speed. The first vehicle with this feature was the Citroën SM with its DIRAVI system,[5] although rather than altering the amount of assistance as in modern power steering systems, it altered the pressure on a centering cam which made the steering wheel try to "spring" back to the straight-ahead position. Modern speed-sensitive power steering systems reduce the mechanical or electrical assistance as the vehicle speed increases, giving a more direct feel. This feature is gradually becoming more common.

Four-wheel steering

Four-wheel steering is a system employed by some vehicles to improve steering response, increase vehicle stability while maneuvering at high speed, or to decrease turning radius at low speed.

Active four-wheel steering

In an active four-wheel steering system, all four wheels turn at the same time when the driver steers. In most active four-wheel steering systems, the rear wheels are steered by a computer and actuators.[6] The rear wheels generally cannot turn as far as the front wheels. There can be controls to switch off the rear steering and options to steer only the rear wheels independently of the front wheels. At low speed (e.g. parking) the rear wheels turn opposite to the front wheels, reducing the turning radius, sometimes critical for large trucks, tractors, vehicles with trailers and passenger cars with a large wheelbase, while at higher speeds both front and rear wheels turn alike (electronically controlled), so that the vehicle may change position with less yaw and improved build-up of the lateral acceleration, enhancing straight-line stability.[6][7] The "snaking effect" experienced during motorway drives while towing a travel trailer is thus largely nullified.

Four-wheel steering found its most widespread use in monster trucks, where maneuverability in small arenas is critical, and it is also popular in large farm vehicles and trucks. Some of the modern European Intercity buses also utilize four-wheel steering to assist maneuverability in bus terminals, and also to improve road stability. Mazda were pioneers in applying four-wheel steering to automobiles, showing it on their 1984 Mazda MX-02 concept car, where the rear wheels counter-steered at low speeds.[8] Mazda proceeded to offer a version of this electronic four-wheel steering system on the Mazda 626 and MX6 in 1988. The first rally vehicle to use the technology was the Peugeot 405 Turbo 16, which debuted at the 1988 Pikes Peak International Hill Climb.[9]

Previously, Honda had mechanical four-wheel steering as an option in their 1987–2001 Prelude and Honda Ascot models (1989–1996) later upgrading to electronically controlled. General Motors offered Delphi's Quadrasteer in their Silverado/Sierra and Suburban/Yukon. Due to low demand, GM discontinued the technology at the end of the 2005 model year.[10] Nissan/Infiniti offer several versions of their HICAS system as standard or as an option in much of their line-up.

In the early 2000s, a new generation of four-wheel steering systems was introduced into the market. In 2001 BMW equipped the E65 7 series with an all-wheel steering system (optional, called 'Integral Active Steering'), which is available on the current 5, 6, and 7 series,[11][12][7] as an option. Renault introduced an optional all-wheel steering called '4control'[13][14][15] in 2009, at first on the Laguna GT, which is currently available on the Talisman,[14] Mégane[13] and Espace[15] vehicle lines. In 2013, Porsche introduced a system on the 911 Turbo as standard equipment.[16] Since 2016, the Panamera has been offered with optional all-wheel steering.[17] The 2014 Audi Q7 was launched with an optional system.[18] Also the Japanese OEMs offer luxury segment vehicles equipped with all-wheel steering, such as Infiniti on its QX70 model ('Rear Active Steering')[19] and Lexus on the GS.[20] Italian manufacturers have launched the technology in the model years 2016–17 with the Ferrari F12tdf,[21] the Ferrari GTC4Lusso[22] as well as the Lamborghini Aventador S Coupé.[23]

Crab steering

Crab steering is a special type of active four-wheel steering. It operates by steering all wheels in the same direction and at the same angle. Crab steering is used when the vehicle needs to proceed in a straight line but at an angle: when changing lanes on a highway at speed, when moving loads with a reach truck, or during filming with a camera dolly.

Rear wheel steering can also be used when the rear wheels may not follow the path taken by the front wheel tracks (e.g. to reduce soil compaction when using rolling farm equipment).

Passive rear-wheel steering

Many modern vehicles have passive rear-wheel steering. On many vehicles, when cornering, the rear wheels tend to steer slightly to the outside of a turn, which can reduce stability. The passive steering system uses the lateral forces generated in a turn (through suspension geometry) and the bushings to correct this tendency and steer the wheels slightly to the inside of the corner. This improves the stability of the car through the turn. This effect is called compliance understeer; it, or its opposite, is present on all suspensions. Typical methods of achieving compliance understeer are to use a Watt's link on a live rear axle, or the use of toe control bushings on a twist beam suspension. On an independent rear suspension it is normally achieved by changing the rates of the rubber bushings in the suspension. Some suspensions typically have compliance oversteer due to geometry, such as Hotchkiss live axles, semi-trailing arm IRS, and rear twist beams, but may be mitigated by revisions to the pivot points of the leaf spring or trailing arm, or additional suspension links, or complex internal geometry of the bushings.

Passive rear-wheel steering is not a new concept, as it has been in use for many years, although not always recognized as such.

Articulated steering

Front loader with articulated steering (2007).

Articulated steering is a system by which a vehicle is split into front and rear halves which are connected by a vertical hinge. The front and rear halves are connected with one or more hydraulic cylinders that change the angle between the halves, including the front and rear axles and wheels, thus steering the vehicle. This system does not use steering arms, king pins, tie rods, etc. as does four-wheel steering. If the vertical hinge is placed equidistant between the two axles, it also eliminates the need for a central differential in four-wheel drive vehicles, as both front and rear axles will follow the same path, and thus rotate at the same speed. Articulated haulers have very good off-road performance.

Vehicle-trailer-combinations such as semi-trailers, road trains, articulated buses, and internal transport trolley trains can be regarded as passively-articulated vehicles.

Rear-wheel steering

A few types of vehicle use only rear-wheel steering, notably fork lift trucks, camera dollies, early pay loaders, Buckminster Fuller's Dymaxion car, and the ThrustSSC.[24]

In cars, rear-wheel steering tends to be unstable because, in turns, the steering geometry changes, hence decreasing the turn radius (oversteer), rather than increasing it (understeer). Rear-wheel steering is meant for slower vehicles that need high-maneuverability in tight spaces, e.g. fork lifts.

For heavy haulage or for increased maneuverability, some semi-trailers are fitted with rear-wheel steering, controlled electro-hydraulically. The wheels on all or some of the rear axles may be turned through different angles to enable tighter cornering, or through the same angle (crab steering) to move the rear of the trailer laterally.

Steer-by-wire

1971 Lunar Roving Vehicle (LRV) with joystick steering controls.
2012 Honda EV-STER "Twin Lever Steering" concept.
Heavy transport trailer with all-wheel steering remote controlled by a steersman walking at the rear of the trailer (2008).

The aim of steer-by-wire technology is to completely remove as many mechanical components (steering shaft, column, gear reduction mechanism, etc.) as possible. Completely replacing conventional steering system with steer-by-wire has several advantages, such as:

  • The absence of steering column simplifies the car interior design.
  • The absence of steering shaft, column and gear reduction mechanism allows much better space utilization in the engine compartment.
  • The steering mechanism can be designed and installed as a modular unit.
  • Without mechanical connection between the steering wheel and the road wheel, it is less likely that the impact of a frontal crash will cause the steering wheel to impact the driver.
  • Steering system characteristics can easily be adjusted to change the steering response and feel.

Steer-by-wire without the use of a steering column was first offered in a production car with the Nissan Infiniti Q50 in 2013.[25] Steer-by-wire continued to be offered with the QX50 and QX55, and as of 2022 is being offered with the Infiniti Q60 coupe.[26]

Production battery electric vehicles in the 2020s that offer steer-by-wire with no steering column include the Canoo Lifestyle Vehicle,[27] Lexus RZ 450e,[28] REE Automotive P7-module-based vehicles,[29] and Toyota bZ4X.[26] As of 2023 Lotus,[30] Peugeot,[31] Mercedes-Benz, and purportedly Tesla plan to offer steer-by-wire cars in the mid to late 2020s.[32]

Safety

Traditionally, cars feature a collapsible steering column (energy absorbing steering column) which will collapse in the event of a heavy frontal impact to avoid excessive injuries to the driver. Airbags are also generally fitted as standard. Non-collapsible steering columns fitted to older vehicles very often impaled drivers in frontal crashes, particularly when the steering box or rack was mounted in front of the front axle line, at the front of the crumple zone. This was particularly a problem on vehicles that had a rigid separate chassis frame with no crumple zone. Many modern vehicle steering boxes or racks are mounted behind the front axle on the front bulkhead, at the rear of the front crumple zone.

Collapsible steering columns were invented by Béla Barényi and were introduced in the 1959 Mercedes-Benz W111 Fintail, along with crumple zones. This safety feature first appeared on cars built by General Motors after an extensive and very public lobbying campaign enacted by Ralph Nader. Ford started to install collapsible steering columns in 1968.[33]

Audi used a retractable steering wheel and seat belt tensioning system called procon-ten, but it has since been discontinued in favor of airbags and pyrotechnic seat belt pre-tensioners.

Cycles

Differential steering

Differential steering is the primary means of steering tracked vehicles, such as tanks and bulldozers;[34] it is also used in certain wheeled vehicles commonly known as skid-steers, and implemented in some automobiles, where it is called torque vectoring, to augment steering by changing wheel direction relative to the vehicle.

Regulations

In the European Union, Russia and Japan, United Nations Economic Commission for Europe (UNECE) vehicle regulation 79 is related to steering.

In the United States, Federal Motor Vehicle Safety Standards 203 and 204 are related to impact protection for the driver from the steering control system and steering control rearward displacement while 49 Code of Federal Regulations § 393.209 is related to steering wheel systems.

In North America, “hands-off” or “hands-free” level-2 systems allowing the drivers to remove both hands from the steering wheel were introduced and legally permitted. General Motors' Super Cruise is such an implementation. In those designs warnings are raised when driver disengages his/her visual attention.[35]

In May 2023, in Europe, UNECE regulation 79 still requires assistant systems for steering to prompt drivers not to remove their hands from the steering wheel. Those systems are known as “hands-on” systems. With “hands-on” assisted driving systems, British and European drivers are required by the system itself to keep one or both hands on the steering wheel, as with unassisted driving: When driving with assisted steering, if drivers remove both hands from the steering wheel, an optical warning occurs after the first 15 seconds and an acoustic warning occurs after 15 more seconds. Assisted steering is deactivated after additional 30 seconds.[35]

In the United Kingdom, drivers must control the vehicle at all times, and Rule 160 of the Highway Code instructs to "drive with both hands on the wheel where possible." and to "use (ADAS) according to the manufacturer’s instructions."[35]

See also

References

  1. Smith Hempstone, Oliver (1974), Wheels and Wheeling: The Smithsonian Cycle Collection, pp. 1–7, doi:10.5479/si.00810258.24.1
  2. The Nobel Institute for Neurophysiology (May 30, 2009), "Steering", Karolinska Institutet
  3. Smyth, William Henry; Belcher, Edward (1867). The sailor's word-book: An alphabetical digest of nautical terms, including some more especially military and scientific ... as well as archaisms of early voyagers, etc. London: Blackie and Son. p. 654.
  4. "Rack and Pinion Steering | Hemmings Motor News". Archived from the original on July 10, 2015. Retrieved July 24, 2015.
  5. "Top 5: Citroen SM innovations that saw the future - Video". Archived from the original on May 11, 2015. Retrieved May 28, 2015.
  6. "Cars | AKC® - Active Kinematics Control - ZF Friedrichshafen AG". www.zf.com. Archived from the original on April 7, 2017. Retrieved April 6, 2017.
  7. AG, BMW. "BMW 5 Series Sedan: Driving dynamics & Efficiency". www.bmw.com. Archived from the original on April 6, 2017. Retrieved April 6, 2017.
  8. Lindell, Hannu (March 19, 1985). "Nelosten vuosi" [Year of the Four]. Tekniikan Maailma (in Finnish). Vol. 41, no. 5/85. Helsinki: TM-Julkaisu. p. Automaailma 3. ISSN 0355-4287.
  9. "1988 Peugeot 405 T16 GR Pikes Peak". Retrieved March 16, 2015.
  10. Murphy, Tom; Corbett, Brian (March 1, 2005). "Quadrasteer Off Course". Wards Auto World. Archived from the original on March 23, 2011. Retrieved June 11, 2010.
  11. AG, BMW. "BMW 7 Series Sedan : M Performance". www.bmw.com. Archived from the original on April 6, 2017. Retrieved April 6, 2017.
  12. AG, BMW. "BMW 6 Series Coupé : Driving dynamics". www.bmw.com. Archived from the original on April 6, 2017. Retrieved April 6, 2017.
  13. "Feature | All-New MEGANE Sport Tourer | Cars | Renault UK". Renault. Archived from the original on April 6, 2017. Retrieved April 6, 2017.
  14. "Equipements | Talisman | Véhicules Particuliers | Véhicules | Renault FR". Renault (in French). Archived from the original on April 7, 2017. Retrieved April 6, 2017.
  15. "Equipements | Espace | Véhicules Particuliers | Véhicules | Renault FR". Renault (in French). Archived from the original on April 7, 2017. Retrieved April 6, 2017.
  16. "Porsche 911 Turbo - Rear-axle steering - Porsche Great Britain". Porsche Great Britain - Dr. Ing. h.c. F. Porsche AG. Archived from the original on April 7, 2017. Retrieved April 6, 2017.
  17. "Porsche The new Panamera - Rear-axle steering - Porsche Great Britain". Porsche Great Britain - Dr. Ing. h.c. F. Porsche AG. Archived from the original on April 6, 2017. Retrieved April 6, 2017.
  18. "Audi Q7 > Audi configurator UK". www.uk.audi.com. Archived from the original on April 6, 2017. Retrieved April 6, 2017.
  19. "INFINITI QX70 Specs - Performance Features & Engine Options". Infiniti. Archived from the original on April 6, 2017. Retrieved April 6, 2017.
  20. "News&Events, Neuigkeiten". www.lexus.de (in German). Archived from the original on February 22, 2017. Retrieved April 6, 2017.
  21. "Ferrari F12tdf: Track-Level Performance on the Road - Ferrari.com". Ferrari GT - en-EN. Archived from the original on April 7, 2017. Retrieved April 6, 2017.
  22. "GTC4LUSSO T: maximum control for a unique driving experience". GTC4Lusso T. Archived from the original on April 7, 2017. Retrieved April 6, 2017.
  23. "Lamborghini Aventador S Coupé". www.lamborghini.com. Archived from the original on April 25, 2017. Retrieved April 6, 2017.
  24. "Thrust SSC - Engineering". Archived from the original on November 12, 2010. Retrieved May 26, 2010.
  25. Jancer, Matt. "Take a Look Inside the First Steer-by-Wire Car". Archived from the original on March 16, 2014. Retrieved March 6, 2017.
  26. Golson, Jordan (May 21, 2022), "What is Steer-by-Wire?", CapitalOne
  27. Corn, Peter (March 19, 2023), "This is What It Looks Like to Drive the Most Exciting EV, the Canoo Lifestyle Vehicle", MotorBiscuit
  28. Gold, Aaron (May 2, 2022), "2023 Lexus RZ Steer-by-Wire Steering Yoke Review: This Yoke Is No Joke", MotorTrend
  29. Scooter Doll (May 2, 2023), "REE Automotive adds new P7-C chassis cab to its all-electric platform lineup", electrek
  30. Kacher, Georg (July 10, 2023), "2024 Lotus Eletre review: First international drive", Which Car?
  31. Chilton, Chris (January 6, 2023), "Hypersquare Steering On Road Cars By 2026, Peugeot CEO Says", Carscoops
  32. Alaniz, Anthony (July 3, 2023), "New Mercedes S-Class Could Have Yoke Steering Wheel, More Physical Buttons", Motor1.com
  33. Smart, Jim. "Collapsible Steering Column Installation". Archived from the original on December 28, 2006.
  34. Encyclopedia of German Tanks of World War Two by Peter Chamberlain and Hilary Doyle, 1978, 1999
  35. Carsten, Oliver; Perrier, Mickaël; Jamson, Samantha (May 2023). Driver Attentiveness to the Driving Task During ADAS Use (Technical report). UK: Iniversity of Leeds. doi:10.13140/RG.2.2.31985.04961.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.