Adaptive optics

Negative images of a star through a telescope. The left-hand panel shows the slow-motion movie of a star when the adaptive optics system is switched off. The right-hand panel shows the slow motion movie of the same star when the AO system is switched on.

When light from a star or another astronomical object enters the Earth's atmosphere, atmospheric turbulence (introduced, for example, by different temperature layers and different wind speeds interacting) can distort and move the image in various ways.[11] Visual images produced by any telescope larger than approximately 20 centimetres (0.20 m; 7.9 in) are blurred by these distortions.

An adaptive optics system tries to correct these distortions, using a wavefront sensor which takes some of the astronomical light, a deformable mirror that lies in the optical path, and a computer that receives input from the detector.[12] The wavefront sensor measures the distortions the atmosphere has introduced on the timescale of a few milliseconds; the computer calculates the optimal mirror shape to correct the distortions and the surface of the deformable mirror is reshaped accordingly. For example, an 8–10-metre (800–1,000 cm; 310–390 in) telescope (like the VLT or Keck) can produce AO-corrected images with an angular resolution of 30–60 milliarcsecond (mas) resolution at infrared wavelengths, while the resolution without correction is of the order of 1 arcsecond.

In order to perform adaptive optics correction, the shape of the incoming wavefronts must be measured as a function of position in the telescope aperture plane. Typically the circular telescope aperture is split up into an array of pixels in a wavefront sensor, either using an array of small lenslets (a Shack–Hartmann wavefront sensor), or using a curvature or pyramid sensor which operates on images of the telescope aperture. The mean wavefront perturbation in each pixel is calculated. This pixelated map of the wavefronts is fed into the deformable mirror and used to correct the wavefront errors introduced by the atmosphere. It is not necessary for the shape or size of the astronomical object to be known – even Solar System objects which are not point-like can be used in a Shack–Hartmann wavefront sensor, and time-varying structure on the surface of the Sun is commonly used for adaptive optics at solar telescopes. The deformable mirror corrects incoming light so that the images appear sharp.

Because a science target is often too faint to be used as a reference star for measuring the shape of the optical wavefronts, a nearby brighter guide star can be used instead. The light from the science target has passed through approximately the same atmospheric turbulence as the reference star's light and so its image is also corrected, although generally to a lower accuracy.

The necessity of a reference star means that an adaptive optics system cannot work everywhere on the sky, but only where a guide star of sufficient luminosity (for current systems, about magnitude 12–15) can be found very near to the object of the observation. This severely limits the application of the technique for astronomical observations. Another major limitation is the small field of view over which the adaptive optics correction is good. As the angular distance from the guide star increases, the image quality degrades. A technique known as "multiconjugate adaptive optics" uses several deformable mirrors to achieve a greater field of view.[13]

A laser beam directed toward the centre of the Milky Way. This laser beam can then be used as a guide star for the AO.

An alternative is the use of a laser beam to generate a reference light source (a laser guide star, LGS) in the atmosphere. There are two kinds of LGSs: Rayleigh guide stars and sodium guide stars. Rayleigh guide stars work by propagating a laser, usually at near ultraviolet wavelengths, and detecting the backscatter from air at altitudes between 15–25 km (49,000–82,000 ft). Sodium guide stars use laser light at 589 nm to resonantly excite sodium atoms higher in the mesosphere and thermosphere, which then appear to "glow". The LGS can then be used as a wavefront reference in the same way as a natural guide star – except that (much fainter) natural reference stars are still required for image position (tip/tilt) information. The lasers are often pulsed, with measurement of the atmosphere being limited to a window occurring a few microseconds after the pulse has been launched. This allows the system to ignore most scattered light at ground level; only light which has travelled for several microseconds high up into the atmosphere and back is actually detected.

Ocular aberrations are generally measured using a wavefront sensor, and the most commonly used type of wavefront sensor is the Shack–Hartmann. Ocular aberrations are caused by spatial phase nonuniformities in the wavefront exiting the eye. In a Shack-Hartmann wavefront sensor, these are measured by placing a two-dimensional array of small lenses (lenslets) in a pupil plane conjugate to the eye's pupil, and a CCD chip at the back focal plane of the lenslets. The lenslets cause spots to be focused onto the CCD chip, and the positions of these spots are calculated using a centroiding algorithm. The positions of these spots are compared with the positions of reference spots, and the displacements between the two are used to determine the local curvature of the wavefront allowing one to numerically reconstruct the wavefront information—an estimate of the phase nonuniformities causing aberration.

Once the local phase errors in the wavefront are known, they can be corrected by placing a phase modulator such as a deformable mirror at yet another plane in the system conjugate to the eye's pupil. The phase errors can be used to reconstruct the wavefront, which can then be used to control the deformable mirror. Alternatively, the local phase errors can be used directly to calculate the deformable mirror instructions.

If the wavefront error is measured before it has been corrected by the wavefront corrector, then operation is said to be "open loop".

If the wavefront error is measured after it has been corrected by the wavefront corrector, then operation is said to be "closed loop". In the latter case then the wavefront errors measured will be small, and errors in the measurement and correction are more likely to be removed. Closed loop correction is the norm.

Adaptive optics was first applied to flood-illumination retinal imaging to produce images of single cones in the living human eye. It has also been used in conjunction with scanning laser ophthalmoscopy to produce (also in living human eyes) the first images of retinal microvasculature and associated blood flow and retinal pigment epithelium cells in addition to single cones. Combined with optical coherence tomography, adaptive optics has allowed the first three-dimensional images of living cone photoreceptors to be collected.[14]