Babbitt (alloy)

In the traditional style of a babbitt metal bearing, a cast iron pillow block is assembled as a loose fit around the shaft, with the shaft in its approximate final position. The inner face of the cast iron pillow block is often drilled to form a key to locate the bearing metal as it is cast into place. The shaft is coated with soot as a release agent, the ends of the bearing are packed with clay to form a mold, and molten metal is poured into the cavity around the shaft, initially filling the lower half of the pillow block. The bearing is stripped, and the metal trimmed back to the top surface of the pillow block. Solidified babbitt metal is soft enough to be cut with a knife or sharp chisel.

A steel shim is inserted to protect the face of the lower bearing and to space the cap of the pillow block away from the shaft. After resealing the ends with clay, more metal is then poured to fill the cap of the pillow block through the hole in the top of the pillow block cap, which will eventually become a lubrication port.

The two halves of the bearing are then split at the shim, the shim removed, the oil holes cleared of metal and oil ways are cut into the surface of the new bearing. The shaft is smeared with engineer's blue and rotated in the bearing. When the bearing is disassembled the blue fills the hollows and is rubbed off the high spots, making them visible. The high spots are scraped down, and the process repeated, until a uniform and evenly distributed pattern of blue shows when the shaft is removed. The bearing is then cleaned and lubricated, and shimmed up such that the shaft is held firmly but not binding in the bearing. The bearing is then "run in" by being run heavily lubricated at low load and slow revolution, completing the process of exposing the hard bearing surface. After final adjustment of the shimming, a very reliable and high load capability bearing results.

Before the advent of low cost electric motors, power was distributed through factories from a central engine via overhead shafts running in hundreds of Babbitt bearings. Often leather, fabric or rubber belts would be used to transfer this rotating power to working machines.

The expression a "run bearing" also derives from this style of bearing, since failure of lubrication will lead to heat build-up due to friction in the bearing, eventually leading to the bearing metal melting and running out of the pillow block.

Until the mid-1950s, poured Babbitt bearings were common in automotive applications. The Babbitt was poured into the block or caps using a form. Tin-based Babbitts were used, as they could stand up to the impact loads found on the connecting rods and crankshaft. The poured Babbitt bearings were kept thin. The rods and caps would have shims that could be peeled off as the Babbitt wore down. Ford was known to use two 0.002" on each cap and Babbitt that was 86% tin, 7% copper, 7% antimony (see the KRW catalogs for the Model T). Steel shims were used, as the brass shims used today tend to compress over time, contributing to shorter bearing life. The poured Babbitt bearings commonly get over 50,000 miles of use before needing replacement. Poured Babbitt bearings are also known to fail gracefully, allowing the car to be driven for extended periods of time. The failed bearing is not likely to damage the crankshaft.

Example: modern Miba Babbitt thrust bearing

In more modern practice, the crankshaft and connecting-rod big-end bearings in a modern automobile engine are made of a replaceable steel shell, keyed to the bearing caps. The inner surface of the steel shell is plated with a coating of bronze, which is in turn coated with a thin layer of Babbitt metal as the bearing surface.

The process of laying down this layer of metal is known as Babbitting.

In many applications, rolling-element bearings, such as ball or roller bearings, have replaced Babbitt bearings. Though such bearings can offer a lower coefficient of friction than plain bearings, their key advantage is that they can operate reliably without a continuous pressurized supply of lubricant. Ball and roller bearings can also be used in configurations that are required to carry both radial and axial thrusts. However, rolling-element bearings lack the beneficial damping and shock-load capability provided by fluid-film bearings, such as the Babbitt.

The engineering of a bearing's Babbitt lining is usually completed during the design of the machine. In selecting the proper type of Babbitt for a particular job there are a number of factors to take into consideration, the most important of which are as follows:

1. Surface speed of the shaft
2. Load that the bearing is required to carry

There is no doubt that if a bearing is to be highly loaded in relation to its size, a high-tin alloy is desirable; whereas for much lower-speed work and less heavily loaded bearings, a lead-based Babbitt may be employed and is far more economical.

1. Surface speed of the shaft (the number of feet traveled per minute by the shaft circumferentially):

   Formula: S = π × D × RPM / 12.

   Example: Determine the surface of a 2-inch-diameter shaft going 1,400 revolutions per minute (RPM):

   S = π × D × RPM / 12 = 3.1416 × 2 × 1,400 / 12 = 733.04 ft/min,

   where π = 3.1416, D = diameter of shaft in inches, S = surface speed of the shaft.

2. Load bearing is required to carry (the weight which is being exerted through the combined weights of the shaft and any other direct weights on the shaft and measured in pounds-force per square inch):

   Formula: L = W / (I.D × L.O.B.).

   Example: Determine the load on a bearing of a 2-inch I.D. bearing, 5 inches long and carrying a weight of 3,100 lbf:

   W / (I.D x L.O.B.) = 3,100 / (2 × 5) = 310 lbf/in²,

   where W = total weight carried by bearing, I.D = inside diameter of bearing, L.O.B = length of bearing, L = load bearing required to carry.

While not subject to precise calculations, the following considerations must also be taken into account:

• Continuity of service
• Bonding characteristics
• Cooling facilities
• Lubrication
• Cleanliness
• Maintenance schedule for the bearing in use

For example, a bearing in continuous use in a harsh environment without regular maintenance will require different Babbitt and lubrication than a bearing in intermittent use in a clean, light duty environment. This so-called art is really the condensation of the experience of the technician and the experience of the bearing being rebuilt.

If the bearing has performed well in use over many years, the bearing needs simply to be rebuilt to its original specification and formulation. In this case the technician's greatest concerns are:

1. Bearing shell surface preparation
2. Bonding characteristics of the tinning compound and the Babbitt layer and,
3. Load bearing surface preparation and finish

Eco-Babbitt is an alloy of 90% Sn, 7% Zn, 3% Cu that is not technically a Babbitt metal. See Solder alloys for more information on Eco-Babbitt.[7]

• Houghton Mifflin (2000). The American Heritage Dictionary of the English Language (4th ed.). Boston and New York: Houghton Mifflin. ISBN 978-0-395-82517-4..
• Oberg, Erik; Green, Robert E. (1996). Machinery's Handbook: A Reference Book for the Mechanical Engineer, Designer, Manufacturing Engineer, Draftsman, Toolmaker, and Machinist. Industrial Press. ISBN 9780831125752.

Look up babbitt metal or babbitt in Wiktionary, the free dictionary.

• "How white metal is moulded to steam locomotive big-end bearings". Ropley, Mid Hants Railway. Archived from the original on 2011-10-09. Retrieved 2011-07-01.
• "How to Pour Babbitt Bearings". WikiHow.