Building insulation material

• Blocks airflow by expanding & sealing off leaks, gaps and penetrations. (This can also keep out bugs or other vermin)
• Can serve as a semi-permeable vapor barrier with a better permeability rating than plastic sheeting vapor barriers and consequently reduce the buildup of moisture, which can cause mold growth.
• Can fill wall cavities in finished walls without tearing the walls apart (as required with batts).
• Works well in tight spaces (like loose-fill, but superior).
• Provides acoustical insulation (like loose-fill, but superior).
• Expands while curing, filling bypasses, and providing excellent resistance to air infiltration (unlike batts and blankets, which can leave bypasses and air pockets, and superior to some types of loose-fill. Wet-spray cellulose is comparable.).
• Increases structural stability (unlike loose-fill, similar to wet-spray cellulose).
• Can be used in places where loose-fill cannot, such as between joists and rafters. When used between rafters, the spray foam can cover up the nails protruding from the underside of the sheathing, protecting your head.
• Can be applied in small quantities.
• Cementitious foam is fireproof.

• The cost can be high compared to traditional insulation.
• Most foams, with the exception of cementitious foams, release toxic fumes when they burn.[1]
• According to the US Environmental Protection Agency, there is insufficient data to accurately assess the potential for exposures to the toxic and environmentally harmful isocyanates which constitute 50% of the foam material.[2]
• Depending on usage and building codes and environment, most foams require protection with a thermal barrier such as drywall on the interior of a house. For example, a 15-minute fire rating may be required.
• Can shrink slightly while curing if not applied on a substrate heated to the manufacturer's recommended temperature.
• Although CFCs are no longer used, some use HCFCs or HFCs as blowing agents. Both are potent greenhouse gases, and HCFCs have some ozone depletion potential.
• Many foam insulations are made from petrochemicals and may be a concern for those seeking to reduce the use of fossil fuels and oil. However, some foams are becoming available that are made from renewable or recycled sources.[3][4]
• R-value will diminish slightly with age, though the degradation of R-value stops once an equilibrium with the environment is reached. Even after this process, the stabilized R-value is very high.
• Most foams require protection from sunlight and solvents.
• It is difficult to retrofit some foams to an existing building structure because of the chemicals and processes involved.
• If one does not wear a protective mask or goggles, it is possible to temporarily impair one's vision. (2–5 days).
• May require the HVAC system to have a source of fresh outside air, since the structure may not refresh inside air without it.

• Open-cell foam is porous, allowing water vapor and liquid water to penetrate the insulation. Closed-cell foam is non-porous, and not moisture-penetrable, thereby effectively forming a semi-permeable vapor barrier. (N.B., vapor barriers are usually required by the Building Codes, regardless of the type of insulation used. Check with the local authorities to find out the requirements for your area.)
• Closed-cell foams are superior insulators. While open-cell foams typically have R-values of 3 to 4 per inch (RSI-0.53 to RSI-0.70 per inch), closed-cell foams can attain R-values of 5 to 8 per inch (RSI-0.88 to RSI-1.41 per inch). This is important if space is limited, because it allows a thinner layer of insulation to be used. For example, a 1-inch layer of closed-cell foam provides about the same insulation factor as 2 inches of open-cell foam.
• Closed-cell foam is very strong, and structurally reinforces the insulated surface. By contrast, open-cell foam is soft when cured, with little structural strength.
• Open-cell foam requires trimming after installation, and disposal of the waste material. Unlike open-cell foam, closed-cell foam rarely requires any trimming, with little or no waste.

• Open cell foams will allow timber to breathe.
• Open cell foams are incredibly effective as a sound barrier, having about twice the sound resistance in normal frequency ranges as closed-cell foam.
• Open cell foams provide a better economical yield.
• Open cell foams often have a low exothermic reaction temperature; will not harm coatings on electrical wiring, plumbing or other building components.

Cementitious foam

One example is AirKrete,[5] at R-3.9 (RSI-0.69) per inch and no restriction on depth of application. Non-hazardous. Being fireproof, it will not smoke at all upon direct contact with flame, and is a two-hour firewall at a 3.5 in (89 mm) (or normal 2 in × 4 in (51 mm × 102 mm) stud wall) application, per ASTM E-814 testing (UL 1479). Great for sound deadening; does not echo like other foams. Environmentally friendly. Non-expansive (good for existing homes where interior sheathing is in place). Fully sustainable: Consists of magnesium oxide cement and air, which is made from magnesium oxide extracted from seawater. Blown with air (no CFCs, HCFCs or other harmful blowing agents). Nontoxic, even during application. Does not shrink or settle. Zero VOC emission. Chemically inert (no known symptoms of exposure per MSDS). Insect resistant. Mold Proof. Insoluble in water. Disadvantages: Fragile at the low densities needed to achieve the quoted R value[6] and, like all foams, it is more expensive than conventional fiber insulations. In 2010, the Ontario Building Code Commission ruled that AirKrete did not conform to requirements for a specific application in the building code. Their ruling states "As the proposed insulation is not impermeable, it could allow water or moisture to enter the wall assembly, which could then cause damage or deterioration of the building elements."[7] As of 2014-08-21, the domain airkretecanada.com appears to be abandoned.

Polyisocyanurate

Typically R-5.6 (RSI-0.99)[8] or slightly better after stabilization – higher values (at least R-7, or RSI-1.23) in stabilized boards.[9] Less flammable than polyurethane.

Phenolic injection foam

Such as Tripolymer R-5.1 per inch (ASTM-C-177). Known for its air sealing abilities. Tripolymer can be installed in wall cavities that have fiberglass and cellulose in them. Non-hazardous. Not restricted by depth of application. Fire resistant – flame spread 5, smoke spread 0 (ASTM-E-84) – will not smoke at all upon direct contact with flame and is a two-hour firewall at a 3.5 in (89 mm), or normal 2 in × 4 in (51 mm × 102 mm) stud wall, application per ASTM E-199. Great for sound deadening, STC 53 (ASTM E413-73); does not echo like other foams. Environmentally friendly. Non-expansive (good for existing homes where interior sheathing is in place). Fully sustainable: Consists of phenolic, a foaming agent, and air. Blown with air (no CFCs, HCFCs or other harmful blowing agents). Nontoxic, even during application. Does not shrink or settle. Zero VOC emission. Chemically inert (no known symptoms of exposure per MSDS). Insect resistant. Mold Proof. Insoluble in water. Disadvantages: Like all foams, it is more expensive than conventional fiber insulations when only comparing sq ft pricing. When you compare price to R value per sq ft the price is about the same.

Polystyrene (expanded polystyrene (EPS) and extruded polystyrene (XPS))

Closed-cell polyurethane

White or yellow. May use a variety of blowing agents. Resistant to water wicking and water vapor.: An example of a commercial closed-cell polyurethane product:

R-8 per inch. Ecomate ® is a trademarked foam blowing agent technology and family of polyurethanes which has a neutral impact on the environment (the worldwide patent was awarded to Foam Supplies Incorporated (FSI) in 2002. This is a new generation eco-friendly foam blowing agent that is free of Chlorofluorocarbons (CFCs), Hydrochlorofluorocarbons (HCFCs), and Hydrofluorocarbons (HFCs) based on naturally occurring methyl methanoate.

Open-cell (low density) polyurethane

White or yellow. Expands to fill and seal cavity, but expands slowly, preventing damage to the wall. Resistant to water wicking, but permeable to water vapor. Fire resistant. Some types of polyurethane insulation are pour-able.

Here are two commercial open-cell, low-density polyurethane products:

Icynene

Icynene is a trademarked brand of isocyanate open-cell spray foam from Huntsman Building Solutions. The classic version has a thermal resistance (R value) of 3.7 per inch and other versions have even higher values.[10] The formula also includes a flame retardant. Icynene uses water for its spray application and the chemical expansion is caused by the carbon dioxide generated between the water and isocyanate material. Icynene will expand up to 100 times it original size within the first 6 seconds of being applied. Icynene contains no ozone-depleting substances such as CFCs, HFC's, HCFC's. Icynene contains volatile organic compounds (VOCs). Icynene will not emit any harmful gases once cured. Icynene has a Global warming potential of 1. Flammability is relatively low. Icynene maintains its efficiency with no loss of R-Value for the life of the install. Icynene is more expensive compared to traditional insulation methods. Any potential for harm is primarily during the installation phase and particularly for installers.[11] The manufacture of icynene involves many toxic petrochemicals.

Sealection 500 spray foam

R-3.8 (RSI-0.67) per inch.[12] a water-blown low density spray polyurethane foam that uses water in a chemical reaction to create carbon dioxide and steam which expands the foam. Flame spread is 21 and smoke developed is 217 which makes it a Class I material (best fire rating). Disadvantages: Is an Isocyanate.

• Strong. Able to bear loads, including external loads from precipitation and wind.
• Faster construction than stick-built house. Less lumber required.
• Insulate acoustically.
• Impermeable to moisture.
• Can truck prefabricated panels to construction site and assemble on site.
• Create shell of solid insulation around house, while reducing bypasses common with stick-frame construction. The result is an inherently energy-efficient house.
• Do not use formaldehyde, CFCs, or HCFCs in manufacturing.
• True R-values and lower energy costs.

• More expensive than other types of insulation.
• Thermal bridging at splines and lumber fastening points unless a thermally broken spline is used (insulated lumber).

• Rock and slag wool. Usually made from rock (basalt, diabase) or iron ore blast furnace slag. Some rock wool contains recycled glass. Nonflammable.
• Fiberglass. Made from molten glass, usually with 20% to 30% recycled industrial waste and post-consumer content.[14] Nonflammable, except for the facing (if present). Sometimes, the manufacturer modifies the facing so that it is fire-resistant. Some fiberglass is unfaced, some is paper-faced with a thin layer of asphalt, and some is foil-faced. Paper-faced batts are vapor retarders, not vapor barriers. Foil-faced batts are vapor barriers. The vapor barrier must be installed toward the warm side.
• High-density fiberglass
• Plastic fiber, usually made from recycled plastic. Does not cause irritation like fiberglass, but more difficult to cut than fiberglass. Not used in US. Flammable, but treated with fire-retardant.

During the 2nd century C.100 -C.200 it was the first time human civilisation was introduced to material of cork, and it was only until the 19th century when cork was widely used leading to major industrial production.[20] Cork, which is harvested from the Oak trees generally found in Portugal, Spain and other Mediterranean countries. When a tree reaches 20 to 35 years old, it can be harvested in 10-year intervals for more than 200 years. Oak bark has a lattice-like molecular structure filled with millions of air bubbles giving the bark resilience, elasticity, thermal insulating, acoustic dampening, and shock absorbing properties. The material is sustainable, reusable and recyclable.

There are two types of cork, the pure cork, which is preferable due to its natural bonding properties, and the agglomeration cork. The pure cork is made by processes of heating and steaming whereby cork granulates are molded into a block. The natural resin of the cork acts as a bonding agent. An artificial bonding agent is required for the production of agglomeration cork.

Cork is typically used for acoustic and thermal insulation within walls, floors, ceilings and facades. A natural fire retardant, thermal insulating cork board is also non-allergenic, simple-to-install and a considerably safer substitute to fiber and plastic based insulation. Notable challenges with cork include difficulty in maintenance and cleaning especially if the material is exposed to heavy use such as insulation for flooring. Minor damages to cork surface can make the material more prone to staining.[21]

Sheep's wool insulation is a very efficient thermal insulator with a similar performance to fiberglass, approximately R13-R16 for a 4-inch-thick layer.[22] Sheep's wool has no reduction in performance even when condensation is present, but its fire retarding treatment can deteriorate through repeated moisture.[23] It is made from the waste wool that the carpet and textile industries reject, and is available in both rolls and batts for both thermal and acoustic insulation of housing and commercial buildings. Wool is capable of absorbing as much as 40% of its own weight in condensation while remaining dry to the touch. As wool absorbs moisture it heats up and therefore reduces the risk of condensation. It has the unique ability to absorb VOC gases such as formaldehyde, nitrogen dioxide, sulphur dioxide and lock them up permanently. Sheep's wool insulation has a long lifetime due to the natural crimp in the fibre, endurance testing has shown it has a life expectancy of over 100 years.

Wood fiber insulation is available as loose fill, flexible batts and rigid panels for all thermal and sound insulation uses. It can be used as internal insulation : between studs, joists or ceiling rafters, under timber floors to reduce sound transmittance, against masonry walls or externally : using a rain screen cladding or roofing, or directly plastered/rendered,[24] over timber rafters or studs or masonry structures as external insulation to reduce thermal bridges. There are two manufacturing processes:

• a wet process similar to pulp mills in which the fibers are softened and under heat and pressure the ligin in the fibres is used to create boards. The boards are limited to approximately 25 mm thickness; thicker boards are made by gluing (with modified starch or PVA wood glue). Additives such as latex or bitumen are added to increase water resistance.
• a dry process where a synthetic binder such as pet (polyester melted bond), polyolefin or polyurethane is added and the boards/batts pressed to different densities to make flexible batts or rigid boards.

Cotton insulation is increasing in popularity as an environmentally preferable option for insulation. It has an R-value of around 3.7 (RSI-0.65), equivalent to the median value for fiberglass batts. The cotton is primarily recycled industrial scrap, providing a sustainability benefit. The batts do not use the toxic formaldehyde backing found in fiberglass, and the manufacture is nowhere near as energy intensive as the mining and production process required for fiberglass. Boric acid is used as a flame retardant. A small quantity of polyolefin is melted as an adhesive to bind the product together (and is preferable to formaldehyde adhesives). Installation is similar to fiberglass, without the need for a respirator but requiring some additional time to cut the material. Cotton insulation costs about 10-20% more than fiberglass insulation.[23] As with any batt insulation, proper installation is important to ensure high energy efficiency.[25]

• Equivalent R-Value to typical fiberglass batts
• Recycled content, no formaldehyde or other toxic substances, and very low toxicity during manufacture (only from the polyolefin)
• May help qualify for LEED or similar environmental building certification programs
• Fibers do not cause itchiness, no cancer risk from airborne fibers

• Difficult to cut. Some installers may charge a slightly higher cost for installation as compared to other batts. This does not affect the effectiveness of the insulation, but may require choosing an installer more carefully, as any batt should be cut to fit the cavity well.
• Even with proper installation, batts do not completely seal the cavity against air movement (as with cellulose or expanding foam).
• Still requires a vapor retarder or barrier (unlike cellulose)
• May be hard to dry if a leak allows excessive moisture into the insulated cavity

• Cellulose insulation is environmentally preferable (80% recycled newspaper) and safe. It has a high recycled content and less risk to the installer than fiberglass (loose fill or batts).[27]
• R-Value 3.4 – 3.8 (RSI-0.60 – 0.67) per inch (imperial units)
• Loose fill insulation fills the wall cavity better than batts. Wet-spray applications typically seal even better than dry-spray.
• Class I fire safety rating
• No formaldehyde-based binders
• Not made from petrochemicals nor chemicals with a high toxicity

• Weight may cause ceilings to sag if the material is very heavy. Professional installers know how to avoid this, and typical sheet rock is fine when dense-packed.
• Will settle over time, losing some of its effectiveness. Unscrupulous contractors may "fluff" insulation using fewer bags than optimal for a desired R-value. Dry-spray (but not wet-spray) cellulose can settle 20% of its original volume.[28] However, the expected settling is included in the stated R-Value. The dense-pack dry installation reduces settling and increases R-value.
• R-values stated on packaging are based on laboratory conditions; air infiltration can significantly reduce effectiveness, particularly for fiberglass loose fill. Cellulose inhibits convection more effectively. In general, loose fill is seen as being better at reducing the presence of gaps in insulation than batts, as the cavity is sealed more carefully. Air infiltration through the insulating material itself is not studied well, but would be lower for wet-spray insulations such as wet-spray cellulose.
• May absorb moisture.[29]

• Rock and slag wool, also known as mineral wool or mineral fiber. Made from rock (basalt, diabase), iron ore blast furnace slag, or recycled glass. Nonflammable. More resistant to airflow than fiberglass. Clumps and loses effectiveness when moist or wet, but does not absorb much moisture, and regains effectiveness once dried. Older mineral wool can contain asbestos, but normally this is in trace amounts.
• Cellulose insulation. Cellulose, is denser and more resistant to air flow than fiberglass. Persistent moisture will weaken aluminium sulphate flame-retardants in cellulose (which are sometimes used in the US). However, borate fire retardants (used primarily in Australia and commonly in the US) have been in use for more than 30 years and are not affected by moisture in any way. Dense-pack cellulose is highly resistant to air infiltration and is either installed into an open wall cavity using nets or temporary frames, or is retrofitted into finished walls. However, dense-pack cellulose blocks, but does not permanently seal, bypasses, in the way a closed-cell spray foam would. Furthermore, as with batts and blankets, warm, moist air will still pass through, unless there is a continuous near-perfect vapor barrier.
• Wet-spray cellulose insulation is similar to loose-fill insulation, but is applied with a small quantity of water to help the cellulose bind to the inside of open wall cavities, and to make the cellulose more resistant to settling. Spray application provides even better protection against air infiltration and improves wall rigidity. It also allows application on sloped walls, attics, and similar spaces. Wet-spray is best for new construction, as the wall must be allowed to dry completely before sealing with drywall (a moisture meter is recommended). Moist-spray (also called stabilized) cellulose uses less water to speed up drying time.
• Fiberglass. Usually pink, yellow, or white. Loses effectiveness when moist or wet, but does not absorb much water. Nonflammable. See Health effects of fiberglass.
• Natural insulations such as granulated cork, hemp fibres, grains, all which can be treated with a low toxicity fire and insect retardants
• Vermiculite. Generally gray or brown.
• Perlite. Generally white or yellow.
• Cotton, wool, hemp, corn cobs, strawdust and other harvested natural materials. Not common.
• Granulated cork. Cork is as good an insulator as foam. It does not absorb water as it consists of closed cells. Resists fire. Used in Europe.
• Most plant based insulations such as wood chips, wood fiber, sawdust, redwood bark, hemlock fiber, balsa wood, hemp fiber, flax fiber, etc. are hygroscopic. Wood absorbs water, which reduces its effectiveness as a thermal insulator. In the presence of moisture, wood is susceptible to mold, mildew, and rot. Careful design of wall, roof and floor systems as done in Europe avoid these problems which are due to poor design.

US regulatory standards for cellulose insulation

• 16 CFR Part 1209 (Consumer Products Safety Commission, or CPSC) – covers settled density, corrosiveness, critical radiant flux, and smoldering combustion.
• ASTM Standard C-739 – loose-fill cellulose insulation – covers all factors of the CPSC regulation and five additional characteristics, R-value, starch content, moisture absorption, odor, and resistance to fungus growth.
• ASTM Standard C-1149 – Industry standard for self-supported spray-applied cellulose insulation for exposed or wall cavity application – covers density, R-value, surface burning, adhesive strength, smoldering combustion, fungi resistance, corrosion, moisture vapor absorption, odor, flame resistance permanency (no test exists for this characteristic), substrate deflection (for exposed application products), and air erosion (for exposed application products).
• 16 CFR Part 460 – (Federal Trade Commission regulation) commonly known as the "R-Value Rule," intended to eliminate misleading insulation marketing claims and ensure publication of accurate R-Value and coverage data.

• Foil or "reflective foil laminate"s (RFL).
• Foil-faced polyurethane or foil-faced polyisocyanurate panels.
• Foil-faced polystyrene. This laminated, high density EPS is more flexible than rigid panels, works as a vapor barrier, and works as a thermal break. Uses include the underside of roof sheathing, ceilings, and on walls. For best results, this should not be used as a cavity fill type insulation.
• Foil-backed bubble pack. This is thin, more flexible than rigid panels, works as a vapor barrier, and resembles plastic bubble wrap with aluminum foil on both sides. Often used on cold pipes, cold ducts, and the underside of roof sheathing.
• Light-colored roof shingles and reflective paint. Often called cool roofs, these help to keep attics cooler in the summer and in hot climates. To maximize radiative cooling at night, they are often chosen to have high thermal emissivity, whereas their low emissivity for the solar spectrum reflects heat during the day.
• Metal roofs; e.g., aluminum or copper.

Radiant barriers can function as a vapor barriers and serve both purposes with one product.

Materials with one shiny side (such as foil-faced polystyrene) must be positioned with the shiny side facing an air space to be effective. An aluminum foil radiant barrier can be placed either way – the shiny side is created by the rolling mill during the manufacturing process and does not affect the reflective of the foil material. As radiant barriers work by reflecting infra-red energy, the aluminum foil would work just the same if both sides were dull.

Aluminum panel facing an air space.

Insulation is a barrier material to resist/reduce substance (water, vapor, etc. ) /energy (sound, heat, electric, etc.) to transfer from one side to another.

Heat/ Thermal Insulation is a barrier material to resist / block / reflect the heat energy (either one or more of the Conduction, Convection or Radiation) to transfer from one side to another.

Reflective Insulation is one of the Heat/Thermal Insulation to reflect Radiation Heat (Radiant Heat) transfer from one side to another due to the reflective surface (or low emittance).

There are a lot of definitions about “Thermal/Heat Insulation” and the common misinterpretation of “Thermal/Heat Insulation” = “Bulk/Mass/Batt Insulation” which is actually uses to resist Conduction Heat Transfer with certain "R-Value".

As such Materials reflecting Radiant Heat with negligible “R-Value” should also be classified as “Thermal/ Heat Insulation”.

Thus Reflective Insulation = Radiant Barrier

• Very effective in warmer climates
• No change in thermal performance over time due to compaction, disintegration or moisture absorption
• Thin sheets takes up less room than bulk insulation
• Can act as a vapor barriers
• Non-toxic/non-carcinogenic
• Will not mold or mildew
• Radon retarder, will limit radon penetration through the floor

• Must be combined with other types of insulation in very cold climates
• May result in an electrical safety hazard where the foil comes into contact with faulty electrical wiring

Urea-formaldehyde insulation releases poisonous formaldehyde gas, causing indoor air quality problems. The chemical bond between the urea and formaldehyde is weak, resulting in degradation of the foam cells and emission of toxic formaldehyde gas into the home over time. Furthermore, some manufacturers used excess formaldehyde to ensure chemical bonding of all of the urea. Any leftover formaldehyde would escape after the mixing. Most states outlawed it in the early 1980s after dangers to building occupants were discovered. However emissions are highest when the urea-formaldehyde is new and decrease over time, so houses that have had urea-formaldehyde within their walls for years or decades do not require remediation.

UFFI provides little mechanical strength, as the material is weak and brittle. Before its risks were recognized, it was used because it was a cheap, effective insulator with a high R-value and its open-cell structure was a good acoustic insulator. Though it absorbed moisture easily, it regained effectiveness as an insulator when dried.

Asbestos is a mineral fiber that occurs in rock and soil[30] that has traditionally been used as an insulation material in many homes and buildings. It is fireproof, a good thermal and electrical insulator, and resistant to chemical attack and wear. It has also been found that asbestos can cause cancer when in friable form (that is, when likely to release fibers into the air – when broken, jagged, shredded, or scuffed).

When found in the home, asbestos often resembles grayish-white corrugated cardboard coated with cloth or canvas, usually held in place around pipes and ducts with metal straps. Things that typically might contain asbestos:[31]

• Boiler and furnace insulation.
• Heating duct wrapping.
• Pipe insulation ("lagging").
• Ducting and transite pipes within slabs.
• Acoustic ceilings.
• Textured materials.
• Resilient flooring.
• Blown-in insulation.
• Roofing materials and felts.

All polyurethane foams are composed of petrochemicals. Foam insulation often uses hazardous chemicals with high human toxicity, such as isocyanates, benzene and toluene. The foaming agents no longer use ozone-depleting substances. Personal Protective Equipment is required for all people in the area being sprayed to eliminate exposure to isocyanates which constitute about 50% of the foam raw material.[2]

Fiberglass is the most common residential insulating material, and is usually applied as batts of insulation, pressed between studs. Health and safety issues include potential cancer risk from exposure to glass fibers, formaldehyde off-gassing from the backing/resin, use of petrochemicals in the resin, and the environmental health aspects of the production process. Green building practices shun Fiberglass insulation.

The World Health Organization has declared fiber glass insulation as potentially carcinogenic (WHO, 1998[32]). In October 2001, an international expert review by the International Agency for Research on Cancer (IARC) re-evaluated the 1988 IARC assessment of glass fibers and removed glass wools from its list of possible carcinogens by downgrading the classification of these fibers from Group 2B (possible carcinogen) to Group 3 (not classifiable as to carcinogenicity in humans). All fiber glass wools that are commonly used for thermal and acoustical insulation are included in this classification. IARC noted specifically: "Epidemiologic studies published during the 15 years since the previous IARC Monographs review of these fibers in 1988 provide no evidence of increased risks of lung cancer or mesothelioma (cancer of the lining of the body cavities) from occupational exposures during manufacture of these materials, and inadequate evidence overall of any cancer risk."

The IARC downgrade is consistent with the conclusion reached by the US National Academy of Sciences, which in 2000 found "no significant association between fiber exposure and lung cancer or nonmalignant respiratory disease in the MVF [man-made vitreous fiber] manufacturing environment." However, manufacturers continue to provide cancer risk warning labels on their products, apparently as indeminfication against claims.

However, the literature should be considered carefully before determining that the risks should be disregarded. The OSHA chemical sampling page provides a summary of the risks, as does the NIOSH Pocket Guide.

Miraflex is a new type of fiberglass batt that has curly fibers that are less itchy and create less dust. You can also look for fiberglass products factory-wrapped in plastic or fabric.

Fiberglass is energy intensive in manufacture. Fiberglass fibers are bound into batts using adhesive binders, which can contain adhesives that can slowly release formaldehyde over many years.[33] The industry is mitigating this issue by switching to binder materials not containing formaldehyde; some manufacturers offer agriculturally based binder resins made from soybean oil. Formaldehyde-free batts and batts made with varying amounts of recycled glass (some approaching 50% post-consumer recycled content) are available.

Cellulose is 100% natural and 75–85% of it is made from recycled newsprint. Health issues (if any) appear to be minor, and most concerns around the flame retardants and mold potential seem to be misrepresentations.

• Cellulose is classified by OSHA as a dust nuisance during installation, and the use of a dust mask is recommended.
• Cellulose is treated with a flame retardant and insect repellent, usually boric acid and sometimes borax to resist insects and rodents. To humans, boric acid has a toxicity comparable to table salt.
• Mold has been seen as a potential concern. However, according to the Cellulose Manufacturer's Association, "One thing that has not contributed to mold problems is the growing popularity of cellulose insulation among knowledgeable home owners who are interested in sustainable building practices and energy conservation. Mycology experts (mycology is the study of mold) are often quoted as saying: “Mold grows on cellulose.” They are referring to cellulose the generic material that forms the cell walls of all plants, not to cellulose insulation. Unfortunately, all too often this statement is taken to mean that cellulose insulation is exceptionally susceptible to mold contamination. In fact, due to its favorable moisture control characteristics and other factors associated with the manufacturing process relatively few cases of significant mold growth on cellulose insulation have been reported. All the widely publicized incidents of serious mold contamination of insulation have involved fiber insulation materials other than cellulose.".[34]
• Moisture is always a concern for homes, and the wet-spray application of cellulose may not be a good choice in particularly wet climates unless the insulation can be verified to be dry before drywall is added. In very wet climates the use of a moisture meter will ensure proper installation and eliminate any installation mold issues (almost any insulation that becomes and remains wet can in the future cause a mold issue). The dry-spray application is another option for very wet climates, allowing for a faster installation (though the wet-spray cellulose has an even higher R-value and can increase wall rigidity).

In May 1999, the North American Insulation Manufacturers Association began implementing a comprehensive voluntary work practice partnership with the US Occupational Safety and Health Administration (OSHA). The program, known as the Health and Safety Partnership Program, or HSPP, promotes the safe handling and use of insulation materials and incorporates education and training for the manufacture, fabrication, installation and removal of fiber glass, rock wool and slag wool insulation products. (See health effects of fiberglass). (For authoritative and definitive information on fiber glass and rock and slag wool insulation, as well as the HSPP, consult the North American Insulation Manufacturers Association (NAIMA) website).