Configuration management

CM applied over the life cycle of a system provides visibility and control of its performance, functional, and physical attributes. CM verifies that a system performs as intended, and is identified and documented in sufficient detail to support its projected life cycle. The CM process facilitates orderly management of system information and system changes for such beneficial purposes as to revise capability; improve performance, reliability, or maintainability; extend life; reduce cost; reduce risk and liability; or correct defects. The relatively minimal cost of implementing CM is returned manyfold in cost avoidance. The lack of CM, or its ineffectual implementation, can be very expensive and sometimes can have such catastrophic consequences such as failure of equipment or loss of life.

CM emphasizes the functional relation between parts, subsystems, and systems for effectively controlling system change. It helps to verify that proposed changes are systematically considered to minimize adverse effects. Changes to the system are proposed, evaluated, and implemented using a standardized, systematic approach that ensures consistency, and proposed changes are evaluated in terms of their anticipated impact on the entire system. CM verifies that changes are carried out as prescribed and that documentation of items and systems reflects their true configuration. A complete CM program includes provisions for the storing, tracking, and updating of all system information on a component, subsystem, and system basis.[6]

A structured CM program ensures that documentation (e.g., requirements, design, test, and acceptance documentation) for items is accurate and consistent with the actual physical design of the item. In many cases, without CM, the documentation exists but is not consistent with the item itself. For this reason, engineers, contractors, and management are frequently forced to develop documentation reflecting the actual status of the item before they can proceed with a change. This reverse engineering process is wasteful in terms of human and other resources and can be minimized or eliminated using CM.

Configuration Management originated in the United States Department of Defense in the 1950s as a technical management discipline for hardware material items—and it is now a standard practice in virtually every industry. The CM process became its own technical discipline sometime in the late 1960s when the DoD developed a series of military standards called the "480 series" (i.e., MIL-STD-480, MIL-STD-481 and MIL-STD-483) that were subsequently issued in the 1970s. In 1991, the "480 series" was consolidated into a single standard known as the MIL–STD–973 that was then replaced by MIL–HDBK–61 pursuant to a general DoD goal that reduced the number of military standards in favor of industry technical standards supported by standards developing organizations (SDO).[7] This marked the beginning of what has now evolved into the most widely distributed and accepted standard on CM, ANSI–EIA–649–1998.[8] Now widely adopted by numerous organizations and agencies, the CM discipline's concepts include systems engineering (SE), Integrated Logistics Support (ILS), Capability Maturity Model Integration (CMMI), ISO 9000, Prince2 project management method, COBIT, ITIL, product lifecycle management, and Application Lifecycle Management. Many of these functions and models have redefined CM from its traditional holistic approach to technical management. Some treat CM as being similar to a librarian activity, and break out change control or change management as a separate or stand alone discipline.

CM is the practice of handling changes systematically so that a system maintains its integrity over time. CM implements the policies, procedures, techniques, and tools that manage, evaluate proposed changes, track the status of changes, and maintain an inventory of system and support documents as the system changes. CM programs and plans provide technical and administrative direction to the development and implementation of the procedures, functions, services, tools, processes, and resources required to successfully develop and support a complex system. During system development, CM allows program management to track requirements throughout the life-cycle through acceptance and operations and maintenance. As changes inevitably occur in the requirements and design, they must be approved and documented, creating an accurate record of the system status. Ideally the CM process is applied throughout the system lifecycle. Most professionals mix up or get confused with Asset management (AM, see also ISO/IEC 19770), where it inventories the assets on hand. The key difference between CM and AM is that the former does not manage the financial accounting aspect but on service that the system supports or in other words, that the later (AM) is trying to realize value from an IT asset.[9][10][11]

The CM process for both hardware- and software-configuration items comprises five distinct disciplines as established in the MIL–HDBK–61A[12] and in ANSI/EIA-649. Members of an organization interested in applying a standard change-management process will employ these disciplines as policies and procedures for establishing baselines, manage and control change, and monitor and assess the effectiveness and correctness of progress. The IEEE 12207 process IEEE 12207.2 also has these activities and adds "Release management and delivery". The five disciplines are:

1. CM Planning and Management: a formal document and plan to guide the CM program that includes items such as:
   • Personnel
   • Responsibilities and resources
   • Training requirements
   • Administrative meeting guidelines, including a definition of procedures and tools
   • Baselining processes
   • Configuration control and configuration-status accounting
   • Naming conventions
   • Audits and reviews
   • Subcontractor/vendor CM requirements
2. Configuration Identification (CI): consists of setting and maintaining baselines, which define the system or subsystem architecture, components, and any developments at any point in time. It is the basis by which changes to any part of a system are identified, documented, and later tracked through design, development, testing, and final delivery. CI incrementally establishes and maintains the definitive current basis for Configuration Status Accounting (CSA) of a system and its configuration items (CIs) throughout their lifecycle (development, production, deployment, and operational support) until disposal.
3. Configuration Control: includes the evaluation of all change-requests and change-proposals, and their subsequent approval or disapproval. It covers the process of controlling modifications to the system's design, hardware, firmware, software, and documentation.
4. Configuration Status Accounting: includes the process of recording and reporting configuration item descriptions (e.g., hardware, software, firmware, etc.) and all departures from the baseline during design and production. In the event of suspected problems, the verification of baseline configuration and approved modifications can be quickly determined.
5. Configuration Verification and Audit: an independent review of hardware and software for the purpose of assessing compliance with established performance requirements, commercial and appropriate military standards, and functional, allocated, and product baselines. Configuration audits verify that the system and subsystem configuration documentation complies with the functional and physical performance characteristics before acceptance into an architectural baseline.

The software configuration management (SCM) process is looked upon by practitioners as the best solution to handling changes in software projects. It identifies the functional and physical attributes of software at various points in time, and performs systematic control of changes to the identified attributes for the purpose of maintaining software integrity and traceability throughout the software development life cycle.

The SCM process further defines the need to trace changes, and the ability to verify that the final delivered software has all of the planned enhancements that are supposed to be included in the release. It identifies four procedures that must be defined for each software project to ensure that a sound SCM process is implemented. They are:

1. Configuration identification
2. Configuration control
3. Configuration status accounting
4. Configuration audits

These terms and definitions change from standard to standard, but are essentially the same.

• Configuration identification is the process of identifying the attributes that define every aspect of a configuration item. A configuration item is a product (hardware and/or software) that has an end-user purpose. These attributes are recorded in configuration documentation and baselined. Baselining an attribute forces formal configuration change control processes to be effected in the event that these attributes are changed.
• Configuration change control is a set of processes and approval stages required to change a configuration item's attributes and to re-baseline them.
• Configuration status accounting is the ability to record and report on the configuration baselines associated with each configuration item at any moment of time.
• Configuration audits are broken into functional and physical configuration audits. They occur either at delivery or at the moment of effecting the change. A functional configuration audit ensures that functional and performance attributes of a configuration item are achieved, while a physical configuration audit ensures that a configuration item is installed in accordance with the requirements of its detailed design documentation.

Configuration management is used to maintain an understanding of the status of complex assets with a view to maintaining the highest level of serviceability for the lowest cost. Specifically, it aims to ensure that operations are not disrupted due to the asset (or parts of the asset) overrunning limits of planned lifespan or below quality levels.

In the military, this type of activity is often classed as "mission readiness", and seeks to define which assets are available and for which type of mission; a classic example is whether aircraft on board an aircraft carrier are equipped with bombs for ground support or missiles for defense.

A number of standards support or include configuration management,[19] including:

• ANSI/EIA-649-1998 National Consensus Standard for Configuration Management
• EIA-649-A 2004 National Consensus Standard for Configuration Management
• SAE EIA-649-C 2019 Global Consensus Configuration Management Standard
• ISO 10007 Quality management systems – Guidelines for configuration management
• Federal Standard 1037C
• GEIA Standard 836–2002 Configuration Management Data Exchange and Interoperability
• IEEE 829 Standard for Software Test Documentation
• IEEE Standard for Configuration Management in Systems and Software Engineering. 2012. doi:10.1109/IEEESTD.2012.6170935. ISBN 978-0-7381-7232-3.
• MIL-STD-973 Configuration Management (cancelled on 20 September 2000)[20]
• NATO STANAG 4427 Configuration Management in Systems Life Cycle Management including
• NATO ACMP 2000 Policy on Configuration Management
• NATO ACMP 2009 Guidance on Configuration Management[21]
• NATO ACMP 2100 Configuration Management Contractual Requirements
• CMMI CMMI for Development, Version 1.2 Configuration Management
• CMII-100E CMII Standard for Enterprise Configuration Management[22]
• Extended List of Configuration Management & Related Standards[23]
• ITIL Service Asset and Configuration Management
• ISO 20000:1 2011& 2018 Service Management System.
• ECSS-M-ST-40C Rev.1 Configuration and information management[24]

• IEEE 828-2012 Standard for Configuration Management in Systems and Software Engineering,[25] published date:2012-03-16
• ISO 10007:2017 Quality management – Guidelines for configuration management[26]
• NATO ACMP-2009 – Guidance on configuration management[21]
• ANSI/EIA-632-1998 Processes for Engineering a System
• ANSI/EIA-649-1998 National Consensus Standard for Configuration Management
• GEIA-HB-649 – Implementation Guide for Configuration Management
• EIA-836 Consensus Standard for Configuration Management Data Exchange and Interoperability
• MIL-HDBK-61B Configuration Management Guidance,[27] 7 April 2020
• MIL-STD-3046 Configuration Management,[28] 6 March 2013 and canceled on June 1, 2015
• Defense Acquisition Guidebook,[29] elements of CM at 4.3.7 SE Processes, attributes of CM at 5.1.7 Lifecycle support
• Systems Engineering Fundamentals, Chapter 10 Configuration Management[30]
• Configuration Management Plan United States Dept. of Defense Acquisition document[31]

More recently configuration management has been applied to large construction projects which can often be very complex and have a huge number of details and changes that need to be documented. Construction agencies such as the Federal Highway Administration have used configuration management for their infrastructure projects.[32] There are construction-based configuration management tools that aim to document change orders and RFIs in order to ensure a project stays on schedule and on budget. These programs can also store information to aid in the maintenance and modification of the infrastructure when it is completed. One such application, CCSNet, was tested in a case study funded by the Federal Transportation Administration (FTA) in which the efficacy of configuration management was measured through comparing the approximately 80% complete construction of the Los Angeles County Metropolitan Transit Agency (LACMTA) first and second segments of the Red Line, a $5.3 billion rail construction project. This study yielded results indicating a benefit to using configuration management on projects of this nature.[33]

Wikimedia Commons has media related to Configuration management.

• Change detection
• Granular Configuration Automation
• Comparison of open source configuration management software
• Dependency
• List of software engineering topics
• Interchangeable parts
• Continuous configuration automation
• System configuration
• Systems management