DNA footprinting

The DNA template labeled at the 3' or 5' end, depending on the location of the binding site(s). Labels that can be used are: radioactivity and fluorescence. Radioactivity has been traditionally used to label DNA fragments for footprinting analysis, as the method was originally developed from the Maxam-Gilbert chemical sequencing technique. Radioactive labeling is very sensitive and is optimal for visualizing small amounts of DNA. Fluorescence is a desirable advancement due to the hazards of using radio-chemicals. However, it has been more difficult to optimize because it is not always sensitive enough to detect the low concentrations of the target DNA strands used in DNA footprinting experiments. Electrophoretic sequencing gels or capillary electrophoresis have been successful in analyzing footprinting of fluorescent tagged fragments.[2]

A variety of cleavage agents can be chosen. a desirable agent is one that is sequence neutral, easy to use, and is easy to control. Unfortunately no available agents meet all of these standards, so an appropriate agent can be chosen, depending on your DNA sequence and ligand of interest. The following cleavage agents are described in detail: DNase I is a large protein that functions as a double-strand endonuclease. It binds the minor groove of DNA and cleaves the phosphodiester backbone. It is a good cleavage agent for footprinting because its size makes it easily physically hindered. Thus is more likely to have its action blocked by a bound protein on a DNA sequence. In addition, the DNase I enzyme is easily controlled by adding EDTA to stop the reaction. There are however some limitations in using DNase I. The enzyme does not cut DNA randomly; its activity is affected by local DNA structure and sequence and therefore results in an uneven ladder. This can limit the precision of predicting a protein’s binding site on the DNA molecule.[2][3] Hydroxyl radicals are created from the Fenton reaction, which involves reducing Fe²⁺ with H₂O₂ to form free hydroxyl molecules. These hydroxyl molecules react with the DNA backbone, resulting in a break. Due to their small size, the resulting DNA footprint has high resolution. Unlike DNase I they have no sequence dependence and result in a much more evenly distributed ladder. The negative aspect of using hydroxyl radicals is that they are more time consuming to use, due to a slower reaction and digestion time.[4] Ultraviolet irradiation can be used to excite nucleic acids and create photoreactions, which results in damaged bases in the DNA strand.[5] Photoreactions can include: single strand breaks, interactions between or within DNA strands, reactions with solvents, or crosslinks with proteins. The workflow for this method has an additional step, once both your protected and unprotected DNA have been treated, there is subsequent primer extension of the cleaved products.[6][7] The extension will terminate upon reaching a damaged base, and thus when the PCR products are run side-by-side on a gel; the protected sample will show an additional band where the DNA was crosslinked with a bound protein. Advantages of using UV are that it reacts very quickly and can therefore capture interactions that are only momentary. Additionally it can be applied to in vivo experiments, because UV can penetrate cell membranes. A disadvantage is that the gel can be difficult to interpret, as the bound protein does not protect the DNA, it merely alters the photoreactions in the vicinity.[8]

In vivo footprinting is a technique used to analyze the protein-DNA interactions that are occurring in a cell at a given time point.[9][10] DNase I can be used as a cleavage agent if the cellular membrane has been permeabilized. However the most common cleavage agent used is UV irradiation because it penetrates the cell membrane without disrupting cell state and can thus capture interactions that are sensitive to cellular changes. Once the DNA has been cleaved or damaged by UV, the cells can be lysed and DNA purified for analysis of a region of interest. Ligation-mediated PCR is an alternative method to footprint in vivo. Once a cleavage agent has been used on the genomic DNA, resulting in single strand breaks, and the DNA is isolated, a linker is added onto the break points. A region of interest is amplified between the linker and a gene-specific primer, and when run on a polyacrylamide gel, will have a footprint where a protein was bound.[11] In vivo footprinting combined with immunoprecipitation can be used to assess protein specificity at many locations throughout the genome. The DNA bound to a protein of interest can be immunoprecipitated with an antibody to that protein, and then specific region binding can be assessed using the DNA footprinting technique.[12]

The DNA footprinting technique can be modified to assess the binding strength of a protein to a region of DNA. Using varying concentrations of the protein for the footprinting experiment, the appearance of the footprint can be observed as the concentrations increase and the proteins binding affinity can then be estimated.[2]

To adapt the footprinting technique to updated detection methods, the labelled DNA fragments are detected by a capillary electrophoresis device instead of being run on a polyacrylamide gel. If the DNA fragment to be analyzed is produced by polymerase chain reaction (PCR), it is straightforward to couple a fluorescent molecule such as carboxyfluorescein (FAM) to the primers. This way, the fragments produced by DNaseI digestion will contain FAM, and will be detectable by the capillary electrophoresis machine. Typically, carboxytetramethyl-rhodamine (ROX)-labelled size standards are also added to the mixture of fragments to be analyzed. Binding sites of transcription factors have been successfully identified this way.[13]