Envelope detector

The capacitor in the circuit above stores charge on the rising edge and releases it slowly through the resistor when the input signal amplitude falls. The diode in series rectifies the incoming signal, allowing current flow only when the positive input terminal is at a higher potential than the negative input terminal.

Most practical envelope detectors use either half-wave or full-wave rectification of the signal to convert the AC audio input into a pulsed DC signal. Filtering is then used to smooth the final result. This filtering is rarely perfect and some "ripple" is likely to remain on the envelope follower output, particularly for low frequency inputs such as notes from a bass instrument. Reducing the filter cutoff frequency gives a smoother output, but decreases the high frequency response. Therefore, practical designs must reach a compromise.

Any AM or FM signal ${\displaystyle x(t)}$ can be written in the following form

${\displaystyle x(t)=R(t)\cos(\omega t+\varphi (t))\,}$

In the case of AM, φ(t) (the phase component of the signal) is constant and can be ignored. In AM, the carrier frequency ${\displaystyle \omega }$ is also constant. Thus, all the information in the AM signal is in R(t). R(t) is called the envelope of the signal. Hence an AM signal is given by the function

${\displaystyle x(t)=(C+m(t))\cos(\omega t)\,}$

with m(t) representing the original audio frequency message, C the carrier amplitude and R(t) equal to C + m(t). So, if the envelope of the AM signal can be extracted, the original message can be recovered.

In the case of FM, the transmitted ${\displaystyle x(t)}$ has a constant envelope R(t) = R and can be ignored. However, many FM receivers measure the envelope anyway for received signal strength indication.

The simplest form of envelope detector is the diode detector which is shown above. A diode detector is simply a diode between the input and output of a circuit, connected to a resistor and capacitor in parallel from the output of the circuit to the ground. If the resistor and capacitor are correctly chosen, the output of this circuit should approximate a voltage-shifted version of the original (baseband) signal. A simple filter can then be applied to filter out the DC component.

An envelope detector can also be constructed using a precision rectifier feeding into a low-pass filter.

The envelope detector has several drawbacks:

• The input to the detector must be band-pass filtered around the desired signal, or else the detector will simultaneously demodulate several signals. The filtering can be done with a tunable filter or, more practically, a superheterodyne receiver
• It is more susceptible to noise than a product detector
• If the signal is overmodulated(i.e. modulation index > 1), distortion will occur

Most of these drawbacks are relatively minor and are usually acceptable tradeoffs for the simplicity and low cost of using an envelope detector.

An envelope detector can be used to demodulate a previously modulated signal by removing all high frequency components of the signal. The capacitor and resistor form a low-pass filter to filter out the carrier frequency. Such a device is often used to demodulate AM radio signals because the envelope of the modulated signal is equivalent to the baseband signal.

An envelope detector is sometimes referred to as an envelope follower in musical environments. It is still used to detect the amplitude variations of an incoming signal to produce a control signal that resembles those variations. However, in this case the input signal is made up of audible frequencies.

Envelope detectors are often a component of other circuits, such as a compressor or an auto-wah or envelope-followed filter. In these circuits, the envelope follower is part of what is known as the "side chain", a circuit which describes some characteristic of the input, in this case its volume.

Both expanders and compressors use the envelope's output voltage to control the gain of an amplifier. Auto-wah uses the voltage to control the cutoff frequency of a filter. The voltage-controlled filter of an analog synthesizer is a similar circuit.

Modern envelope followers can be implemented:

1. directly as electronic hardware,
2. or as software using either a digital signal processor (DSP) or
3. on a general purpose CPU.

• Analytic signal
• Attack-decay-sustain-release envelope

• Envelope detector
• Envelope and envelope recovery