Rotor ship

The German engineer Anton Flettner was the first to build a ship which attempted to use the Magnus effect for propulsion.[4][5]

Assisted by Albert Betz, Jakob Ackeret, and Ludwig Prandtl, Flettner constructed an experimental rotor vessel; October 1924 the Germaniawerft finished construction of a large two-rotor ship named Buckau.[6] The vessel was a refitted schooner which carried two cylinders (or rotors) approximately 15 metres (50 ft) high, and 3 metres (10 ft) in diameter, driven by an electric propulsion system of 50 hp (37 kW) power.

The Buckau sailed from Danzig to Scotland across the North Sea in February 1925.[7] The ship could tack (sail into the wind) at 20–30 degrees,[6] hence the rotors did not give cause for concern in stormy weather. The ship was renamed Baden Baden after the German spa town and on 31 March 1926 was sailed to New York via South America, arriving in New York Harbor on 9 May.[8]

Some sources claim that the ship had proved inefficient on these voyages, that the power consumed by spinning 15m tall drums was disproportionate to the propulsive effect when compared with conventional propellers.[9]

That view stands in contrast to others that claim "Due to the impressive performance, the Buckau was put into service to carry bulk cargo across the North Atlantic and the Baltic sea (Seufert & Seufert, 1983). On 31 March 1926, the Buckau, now renamed Baden-Baden sailed to New York via South America, the 6,200 nautical mile voyage across the Atlantic used only 12 tons of fuel oil, compared with 45 tons for a motor ship of the same size without rotors (Nuttall & John, 2016), arriving in New York harbor on 9 May (History of Flettner Rotor, n.d.)." [10]

The latter assessment seems to be more accurate, as the outcome of the Buckau experiment, resulted in the development of the next rotor ship, the Barbara.

In 1926, a larger ship with three rotors, the Barbara was built by the shipyard A.G. Weser in Bremen.[11] It proved to perform reliably as " as a normal freighter in the Mediterranean between 1926 and 1929. By 1928, Flettner had secured orders for six new ships of the Barbara class. However ... there was a global economic crash causing a decrease in consumer buying confidence. In addition to this, Marine Diesel Oil (MDO) and the related engine technology required to utilize it became readily and cheaply available (Nuttall & John, 2016). Fuel prices at that point meant that any savings achieved by the rotor were too small for shipping companies to consider the investment due to the lengthy payback period."[10]

Flensburg catamaran at the Kiel Week 2007

Maersk Pelican's are the largest Flettner rotors in the world, as of 2019

Interest in rotor sails revived in the 1980s, as a way of increasing the fuel efficiency of a conventionally powered ship.

Enercon launched the hybrid rotor ship E-Ship 1 on 2 August 2008. From 2010, it has been used to transport the company's turbine products and other equipment.[12][13] Enercon claim "operational fuel savings of up to 25% compared to same-sized conventional freight vessels."[14]

The University of Flensburg is developing the Flensburg catamaran or Uni-Cat Flensburg, a rotor-driven catamaran.[15]

In 2007, Stephen H. Salter and John Latham proposed the building of 1,500 robotic rotor ships to mitigate global warming. The ships would spray seawater into the air to enhance cloud reflectivity.[16][17] A prototype rotor ship was tested on Discovery Project Earth. The rotors were made of carbon fibre and were attached to a retrofitted trimaran and propelled the vessel stably through the water at a speed of six knots.

In 2009, Wärtsilä proposed a cruiseferry that would utilise Flettner rotors as a means of reducing fuel consumption. The Finnish ferry operator Viking Line adopted the idea, with MS Viking Grace built in 2011–2012, initially without rotors.[18] A rotor system was retrofitted in 2018.[19]

In 2014 and 2015, Norsepower installed twin rotor sails on Finnish shipping company Bore's RoRo vessel M/V Estraden.[20][21][22] In May 2018, the 1996 built cargo ship Fehn Pollux of the German-based Fehn Shipmanagement (Leer) was fitted with an 18m long Flettner rotor of the EcoFlettner type at the front.[23]

In 2018, Norsepower deployed rotor sails with the world's biggest shipping company, Maersk. The Maersk Pelican, an LR2 class tanker, has been fitted with two Norsepower Rotor Sails.[24][25]

The MV Afros (IMO 9746803) bulk carrier has operated four movable rotors over a year with positive results.[26][27][28][29]

In 2021, Norsepower installed five tilting rotor sails onto a Vale-operated iron ore carrier; the tilting design intended to allow maneuvering below bridges.[3][30]

Scandlines operates two hybrid ferries with rotorsail, M/F Copenhagen and M/F Berlin.[31]

In October 2023 Airbus announced that it had commissioned six ships with Flettner rotors for entry into service in 2026 to transport aircraft sections to its US assembly line. [32]