Holding (aeronautics)

In aviation, holding (or flying a hold) is a maneuver designed to delay an aircraft already in flight while keeping it within a specified airspace.[1]

A standard holding pattern. Shown are the entry (green), the holding fix (red) and the holding pattern itself (blue)
This article is about the flight maneuver. For a definition of the idiom "holding pattern", see the Wiktionary entry holding pattern.
For the novel, see Holding Pattern (novel).

Implementation

A holding pattern for instrument flight rules (IFR) aircraft is usually a racetrack pattern based on a holding fix. This fix can be a radio beacon such as a non-directional beacon (NDB) or VHF omnidirectional range (VOR). The fix is the start of the first turn of the racetrack pattern.[2] Aircraft will fly towards the fix, and once there will enter a predefined racetrack pattern. A standard holding pattern uses right-hand turns and takes approximately 4 minutes to complete (one minute for each 180-degree turn, and two one-minute straight ahead sections).[1] Deviations from this pattern can happen if long delays are expected; longer legs (usually two or three minutes) may be used, or aircraft with distance measuring equipment (DME)[2] may be assigned patterns with legs defined in nautical miles rather than minutes.

Usage

The primary use of a holding pattern is to delay aircraft that have arrived at their destination but cannot land yet because of traffic congestion, poor weather, or runway unavailability (for instance, during snow removal or emergencies). Several aircraft may fly the same holding pattern at the same time, separated vertically by 300 m (1,000 ft) or more. This is generally described as a stack or holding stack. As a rule, new arrivals will be added at the top. The aircraft at the bottom of the stack will be taken out and allowed to make an approach first, after which all aircraft in the stack move down one level, and so on. Air traffic control (ATC) will control the whole process, in some cases using a dedicated controller (called a stack controller) for each individual pattern.

One airport may have several holding patterns; depending on where aircraft arrive from or which runway is in use, or because of vertical airspace limitations.

Since an aircraft with an emergency has priority over all other air traffic, it will always be allowed to bypass the holding pattern and go directly to the airport (if possible). This causes more delays for other aircraft already in the stack.[3]

Entry procedures
Inbound and outbound leg

The entry to a holding pattern is often the hardest part for a novice pilot to grasp, and determining and executing the proper entry while simultaneously controlling the aircraft, navigating and communicating with ATC requires practice. There are three standard types of entries: direct, parallel, and offset (teardrop). The proper entry procedure is determined by the angle difference between the direction the aircraft flies to arrive at the beacon and the direction of the inbound leg of the holding pattern.[4]

  • A direct entry is performed just as its name would suggest: the aircraft flies directly to the holding fix, and immediately begins the first turn outbound.
  • In a parallel entry, the aircraft flies to the holding fix, parallels the inbound course for one minute outbound, and then turns back, re-intercepting the inbound track, and continues in the hold from there.
  • In an offset or teardrop entry, the aircraft flies to the holding fix, turns into the protected area, flies for one minute, and then turns back inbound, proceeding to the fix and continuing from there.
  • Standard holding entry diagrams
  • Direct entry (Sector 3)
    Direct entry (Sector 3)
  • Parallel entry (Sector 1)
    Parallel entry (Sector 1)
  • Teardrop entry (Sector 2)
    Teardrop entry (Sector 2)

The parallel and teardrop entry are mirrored in case of a left-hand holding pattern.

Speed limits

Maximum holding speeds are established to keep aircraft within the protected holding area during their one-minute (one-minute and a half above 4,300 m (14,000 ft) MSL) inbound and outbound legs. For civil aircraft (not military) in the United States and Canada, these airspeeds are:[1][5]

  • Up to 1,800 m (6,000 ft) MSL: 200 KIAS
  • From 1,829 to 4,267 m (6,001 to 14,000 ft) MSL: 230 KIAS
  • 4,268 m (14,001 ft) MSL and above: 265 KIAS

The ICAO Maximum holding speeds:[6]

  • Up to 4,300 m (14,000 ft): 430 km/h (230 kn)
  • 4,300 to 6,100 m (14,000 to 20,000 ft): 440 km/h (240 kn)
  • 6,100 to 10,400 m (20,000 to 34,000 ft): 491 km/h (265 kn)
  • Above 10,000 m (34,000 ft): M0.83

With their higher performance characteristics, military aircraft have higher holding speed limits.

See also

References
  1. "Instrument Flying Handbook (FAA-H-8083-15A), Chapter 10" (PDF). U.S. Department of Transportation. 2001. Archived from the original (PDF) on April 11, 2013. Retrieved August 15, 2014.
  2. "Holding Pattern". SKYbrary Aviation Safety skybrary.aero. Retrieved December 29, 2019.
  3. "14 CFR 91.3 – Responsibility and authority of the pilot in command". Archived from the original on March 29, 2008. See Code of Federal Regulations
  4. Instrument Flying Handbook (FAA-H-8083-15A), Standard Entry Procedures, page 10-12. "Instrument Flying Handbook". Retrieved September 19, 2019.
  5. "Aeronautical Information Manual" (PDF). Transport Canada. October 8, 2020. Retrieved November 29, 2020.
  6. ICAO Doc 8168 Vol. I, Aircraft Operations, Volume I Flight Procedures, Part I — Section 6, Chapter 1. Archived 2012-01-31 at the Wayback Machine

ATP, CFI-AI, (2016), https://www.holdingpattern.com/holding-patterns.html

Wikimedia Commons has media related to Holding pattern.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.