Holden straight-six motor

Grey engine
Overview
Production	1948-1963
Layout
Configuration	Straight-six
Displacement	132 cubic inches (2,160 cc) 138 cubic inches (2,262 cc)
Cylinder bore	3.000 in (76.2 mm) 3.062 in (77.8 mm)
Piston stroke	3.125 in (79.4 mm)
Cylinder block material	Cast iron
Cylinder head material	Cast iron
Valvetrain	OHV 2 valves per cyl.
Valvetrain drive system	Timing gears
Compression ratio	6.8:1–7.5:1
Combustion
Fuel system	Carburetor
Fuel type	Gasoline
Oil system	Wet sump
Cooling system	Water-cooled
Output
Power output	60–76 hp (45–57 kW)
Torque output	100–119 lb⋅ft (136–161 N⋅m)
Chronology
Successor	Holden Red engine

The Grey motor, built between 1948 and 1962, earned its name as the engine block was painted grey. This overhead valve engine was first fitted to the Holden 48-215 (and variants) and mated to a three-speed column change gearbox. A three-speed GM Roto-Hydramatic 240 automatic transmission was an option fitted in the latter EK and EJ series. The engine was based on the pre-World War II Buick Straight-6 engine design, and saw only minor changes throughout its 15-year life.

It displaced 132 cubic inches (2,160 cc) in its original form as used by the 48-215 (1948). It developed 60 brake horsepower (45 kW). This engine remained in production for eight years - until the release of the FE series in 1956. At that point, power was increased to 72hp (53kW) by an increase in the compression ratio to 6.8:1. Holden replaced the FC in 1960 with the FB series, and its engine was bored out to 138 cubic inches (2,260 cc). The compression ratio was increased to 7.8:1. It developed 76 brake horsepower (57 kW) at 4200 rpm and 120lb.ft (162N.m) at 1400rpm, providing superior performance to the competing four-cylinder Austin, Morris, Vauxhall and Ford of Britain vehicles. The grey motor was a low stress design for high reliability and featured a low compression ratio. Due to sheer ubiquity, they were popular for racing, and were fitted to many open-wheelers, as well as racing Holdens. With the engines' low-end torque, they also found their way into boats and machinery such as forklift trucks.

This engine ran a seven-port non-crossflow cast-iron cylinder head. There were three Siamese (shared) inlet ports for cylinders 1–2, 3–4 and 5–6, two individual exhaust ports for cylinders 1 and 6, and two siamese exhaust ports for cylinders 2–3 and 4–5 in a layout on one side of the head casting. The inlets were fed by a single-barrel Stromberg carburettor in common and fitted with a traditional Kettering ignition by coil and distributor. The electric system was six volts in the 48-215 and FJ. The earliest grey motors (approximately 100,000) were fitted with Delco-Remy accessories, although Lucas and Bosch equivalents throughout the motor's lifetime replaced these.

The very first production grey motor (1948) was number 1001, and they continued in a single sequence until July 1956, when the prefix "L" was introduced.[1] The change affected all engines numbered L283373 and above, signifying the 12-volt negative-earth engines as fitted to the all new FE model. The prefix "U" was introduced for motors with the original electricals as fitted to the FJ utility and panel van models, which ended in February and May 1957 respectively. The change was effective from engine U283384.[1] The prefix "B" was introduced and the number sequence reset with the introduction of the 138 cubic inches (2.3 L) displacement engine, and ultimately this was replaced by a "J" prefix for motors fitted to EJ vehicles in 1962.

Red engine
Overview
Production	1963–1980
Layout
Configuration	Straight-six
Displacement	130 cubic inches (2,130 cc) 138 cubic inches (2,262 cc) 149 cubic inches (2,447 cc) 161 cubic inches (2,639 cc) 173 cubic inches (2,835 cc) 179 cubic inches (2,940 cc) 186 cubic inches (3,049 cc) 202 cubic inches (3,298cc)
Cylinder bore	3.125 in (79.4 mm) 3.375 in (85.7 mm) 3.500 in (88.9 mm) 3.563 in (90.5 mm) 3.625 in (92.1 mm)
Piston stroke	3.000 in (76.2 mm) 3.250 in (82.6 mm)
Cylinder block material	Cast iron
Cylinder head material	Cast iron
Valvetrain	OHV 2 valves per cyl.
Valvetrain drive system	Timing gears
Compression ratio	8.8:1-9.4:1
Combustion
Fuel system	Carburetor
Fuel type	Gasoline
Oil system	Wet sump
Cooling system	Water-cooled
Output
Power output	77–147 PS (76–145 hp; 57–108 kW)
Torque output	183–263 N⋅m (19–27 kg⋅m; 135–194 lb⋅ft)
Chronology
Predecessor	Holden Grey engine
Successor	Holden Blue engine

Superseding the Grey motor, the Red motor was manufactured between 1963 and 1980. This was a completely new engine and in no way a further development of the grey motor. It featured a seven-bearing crankshaft, full flow oil filter and hydraulic valve lifters. Denoted by the cylinder block painted red, the engine made its debut in the Holden EH in capacities of 149 cubic inches (2,447 cc) and 179 cubic inches (2,930 cc) (or HP) producing 100 and 115 brake horsepower (75 and 86 kW) respectively. This was a power increase of 33 per cent and 53 per cent over the grey motor.[2]

Red six-cylinder engines manufactured after October 1964 had the cubic inch capacity of the engine cast in raised numbers on the side of the block behind the generator/alternator location. Red engines manufactured prior to October 1964 had either no numbers cast (meaning that it was a 149-cubic-inch engine) or the letters "HP" cast (meaning that it was a 179-cubic-inch engine). All Red engines manufactured prior to April 1967 had forged steel crankshafts. This includes all 149 and 179 ci engines, and 161 and 186 ci engines manufactured before that date.

Capacities

• 130 – South Africa, et al. HQ export
• 138 – LC & LJ Torana
• 149
• 161
• 173
• 179
• 186
• 202

Blue engine
Overview
Production	1980-1984
Layout
Configuration	Straight-six
Displacement	173 cubic inches (2,835 cc) 202 cubic inches (3,298cc)
Cylinder bore	3.500 in (88.9 mm) 3.625 in (92.1 mm)
Piston stroke	3.000 in (76.2 mm) 3.250 in (82.6 mm)
Cylinder block material	Cast iron
Cylinder head material	Cast iron
Valvetrain	OHV 2 valves per cyl.
Valvetrain drive system	Timing gears
Compression ratio	8.8:1-9.0:1
Combustion
Fuel system	Carburetor
Fuel type	Gasoline
Oil system	Wet sump
Cooling system	Water-cooled
Output
Power output	103–114 PS (102–112 hp; 76–84 kW)
Torque output	192–231 N⋅m (20–24 kg⋅m; 142–170 lb⋅ft)
Chronology
Predecessor	Holden Red engine
Successor	Holden Black engine

The Blue specification debuted in the 1980 VC Commodore.[4]

The blue motor was a development of the earlier red engine, and incorporated several improvements. The biggest of these changes was the complete redesign of the cylinder head; this was now a 12 port design with individual ports for each cylinder. New revised T5 camshaft. The crankshaft for the 3.3-litre engine now had counterweights on each throw, and stronger connecting rods were used. A two-barrel Varajet carburettor was standard, as was a dual outlet exhaust manifold and a Bosch HEI distributor. It was made in 3.3- and 2.85-litre versions.

Black engine
Overview
Production	1984-1986
Layout
Configuration	Straight-six
Displacement	202 cubic inches (3,298cc)
Cylinder bore	3.625 in (92.1 mm)
Piston stroke	3.250 in (82.6 mm)
Cylinder block material	Cast iron
Cylinder head material	Cast iron
Valvetrain	OHV 2 valves per cyl.
Valvetrain drive system	Timing gears
Compression ratio	8.8:1
Combustion
Fuel system	Carburetor Multi-port fuel injection
Management	Jetronic for EFI variant
Fuel type	Gasoline
Oil system	Wet sump
Cooling system	Water-cooled
Output
Power output	117–144 PS (115–142 hp; 86–106 kW)
Torque output	232–266 N⋅m (24–27 kg⋅m; 171–196 lb⋅ft)
Chronology
Predecessor	Holden Blue engine
Successor	Nissan RB engine (RB30E)

The Black specification was introduced in the 1984 VK Commodore.[5] The black engine was produced in 3.3-litre displacement only in carbureted and fuel-injected versions. The carbureted engine was almost identical to the previous blue engine, the main difference being in the use of computer controlled spark timing (EST) taking its timing pick-up from the flywheel area. The ports were slightly wider spaced, meaning the manifolds will not simply interchange. The fuel-injected version used Bosch LE2-Jetronic multipoint fuel injection and featured a long-runner intake manifold, 6-3-1 tubular exhaust manifold and a conventional HEI ignition.[6] It also had slightly different cylinder head intake ports for improved breathing (along with location notches for the fuel injectors) and revised camshaft specifications, and delivered superior performance and fuel economy over the carbureted version.[7] This engine was painted red, slightly redder than the earlier "red" motors which looked orange compared to the VK EFI motor.

In the 1986 VL Commodore, Holden replaced the Australian-made and designed six-cylinder engines with the Nissan RB30E and RB20E engines. Pending emission standards and the requirement for unleaded fuel made it difficult to re-engineer the Australian engine.[8]

Starfire engine
Overview
Also called	Misfire, Backfire (colloquial)
Production	1978-1986
Layout
Configuration	Straight-four
Displacement	115 cubic inches (1,892 cc)
Cylinder bore	3.500 in (88.9 mm)
Piston stroke	3.000 in (76.2 mm)
Cylinder block material	Cast iron
Cylinder head material	Cast iron
Valvetrain	OHV 2 valves per cyl.
Valvetrain drive system	Timing gears
Compression ratio	8.7:1
Combustion
Fuel system	Carburetor
Fuel type	Gasoline
Oil system	Wet sump
Cooling system	Water-cooled
Output
Power output	79 PS (78 hp; 58 kW)
Torque output	136 N⋅m (14 kg⋅m; 100 lb⋅ft)
Chronology
Predecessor	Opel cam-in-head engine 1.9L
Successor	GM Family II engine 1.6L-2.0L

This 1.9-litre (1,892 cc) powerplant, known as the Starfire engine, was effectively Holden's existing 2.85-litre 173 cu in straight-six with two cylinders removed.[4] Designed and built in Australia to satisfy local content rules, it first appeared in 1978 during the UC Sunbird's production run, replacing the Opel 1.9-litre cam-in-head unit used in LH, LX and earlier UC Torana/Sunbird 4-cylinder models.

Peak power output for the Starfire was 58 kW (78 hp), with a 17.5 second acceleration time from 0–100 kilometres (0–62 mi) in the VC Commodore.[9] This variant's performance meant the need to push the engine hard leading to fuel consumption similar to the straight-sixes. Due to this, it was often nicknamed as Misfire or Backfire. This engine was replaced in the Australian market by the Camira's OHC Camtech unit, however, it continued to be used until 1986 in New Zealand, where it was used to power four-cylinder versions of the VK Commodore.

This engine was also used by Toyota Australia to meet local parts content regulations for the Corona XT130.[10] Engines installed in Toyotas received some slight differences in the form of a unique camshaft, manifold, and carburettor. Toyota called the engine the "1X" and it had a slightly different power curve: 58 kW (78 hp) at 4800 rpm and 136 N⋅m (100 lb⋅ft) at 2400 rpm.[10]

ADR27A was an Australian Design Rule specifying regulations for fuel evaporative and exhaust emissions for Australian passenger motor vehicles effective from 1 July 1976 in order to reduce air pollution. The following engines were ADR27A compliant:

• Red (post 1 July 1976 only)
• Blue
• Black
• Starfire

These engines were fitted with emission control systems which generally resulted in reduced engine output. The following table compares the output of the 202ci Red engine in pre- and ADR27A-compliant versions:

• Holden V8 engine
• Nissan RB engine (Straight six used in the Holden Commodore VL)
• List of GM engines

• Loffler, Don (2006) [1998]. She's a Beauty!: The Story of the First Holdens (New Enlarged ed.). Kent Town: Wakefield Press. p. 310. ISBN 1-86254-734-3.
• Robinson, Peter (2006). AutoBiography: The inside story of Holden's all-new VE Commodore. Woolloomooloo: Focus Publishing. p. 224. ISBN 1-921156-10-4.