Holderness Drain

In 1763, landowners decided that the carrs to the east of the River Hull could be turned into profitable land, and obtained an Act of Parliament to exclude this area from the jurisdiction of the Court of Sewers. It created Holderness Drainage, a legal entity with powers to construct new banks and drains.[7] Plans for the drainage of Holderness were then put together. John Grundy, Jr. was approached to produce plans for the drainage of some 17.19 square miles (44.5 km²) of low-lying land to the east of the River Hull. He worked with John Smeaton on the initial assessment, and the two men visited the area in November.[8] There was significant opposition to his plans for the main outlet to be at Marfleet, since the shipping owners felt that the scouring action of the fresh water on the mud banks near the lower end of the Hull was vital to maintain the Old Harbour, as this part of the river was known. With limited financial resources, Holderness Drainage were unable to resist the pressure, and the plans were altered to have an outlet at Stoneferry on the Hull, and reduced dimensions for the drains.[9] Grundy wrote the final report, completing it on 30 December. Smeaton then reviewed it, and suggested only minor modifications, as he was happy with all the major points. The land surveyor Charles Tate produced an engraved plan, and Grundy went to London to steer the bill for the scheme through Parliament. The bill became an Act of Parliament on 5 April 1764.[8]

Grundy's life was marked by tragedy shortly afterwards, when his wife of 21 years died, and remarkably personal letters between the two engineers have survived. Although busy with the Calder Navigation by then, Smeaton made the time to visit the area with Grundy on 4 July, in response to a request from the Trustees of the scheme to view the low grounds and carrs. Grundy produced a report on 14 July, and then designed the outfall sluice, which had two 10-foot (3.0 m) arches with sluices. Smeaton again reviewed the plans in September, suggesting improvements to the foundations, and this was his last involvement with the scheme. Grundy submitted his report on the sluice in December 1764, which included a detailed bill of quantities, with an estimated cost of £1,800.[10]

It appears that Grundy had been acting as Chief Engineer since July 1764. In addition to the main drain, the scheme involved the construction of 17 miles (27 km) of barrier bank, on the east bank of the River Hull, to prevent inundation of the low-lying land from that source. Construction of the bank had begun in July 1764, with John Hoggard acting as Superintendent of the works. In March 1765, work on the main sluice began, and bricklayers, carpenters and masons were employed. The resident engineer or 'Surveyor' for this part of the work and for the construction of the main drain was Joseph Page, who was paid £80 per year. Throughout the contract, Charles Tate, who had produced the original engraved plan, worked as the land surveyor. Grundy in his capacity as Chief Engineer, visited the sites on four occasions in 1765, and continued to do so until October 1767, when the main drains and sluice were finished. Both he and Page then moved on, but work on the banks and drains continued under the supervision of Hoggard. By the time this first phase was completed in 1772, the cost had been around £24,000.[10]

Some work continued until 1775, consisting largely of raising river banks, making drains deeper, and extending the drains that had been created. However, the system was inadequate, as there were large areas that remained under water near Leven, in the north of the area, and at Weel, to the east of Beverley. Flooding during the winter months was still a regular problem, because the drains could not cope with rain from the low-lying carrs, when they were full with water from higher ground to the north of Holderness. The engineer William Jessop spent a month investigating the problems, studying some 40 square miles (100 km²), and presented a report in July 1786. Further survey work was then carried out by George Plummer, and formed the basis for Jessop's detailed plan, which was agreed in 1787. He produced specifications for drains, embankments, dams and tunnels, with the overriding principle that the water from the uplands to the north should be kept entirely separate from the internal drains of the area.[11] Once the project got under way, Jessop visited from time to time to check on progress. He made a total of seven visits between 1789 and 1792,[12] when his involvement and that of George Plummer, who had acted as resident engineer, ceased. Anthony Bower then took over as resident engineer, overseeing the work until 1795. This phase of the scheme was finally completed in 1805, at a cost of £16,000.[13]

Holderness Drain
Start of Holderness Drain Burshill Park drain Baswick Steer drain Heighholme drain Leven North Carr drain Leven Canal (aqueduct missing) Leven Town drain Cross drain Eske Carrs drain Turf Gutter A1035 Monk Bridge Tickton pumping station A1035 Tickton Bridge Monk Dike Turf Gutter & Eske River Side drain Routh & Meaux drain Arnold West Carr drain New Holland drain Monkbridge Stream Old Main drain Meaux Bridge Arnold & Riston drain Foredyke Stream + Great Culvert Foredyke Stream Great Culvert pumping station Foredyke Stream Hornsea Rail Trail Suttoncross drain Ganstead drain B1237 Salthouse Road Bridge A165 bridge Marfleet Lane bridge Maybury Road bridge Preston Road bridge A63 Hedon Road bridge East Hull Pumping Station Outlet sluice Alexandra / King George Docks Entrance locks Humber

Despite the large amounts of money spent on the schemes, they were not particularly effective, because of the failure to provide an outfall at Marfleet. Ship owners continued to oppose such a plan until at least 1810, and there was an agricultural depression from 1815 to 1830. During this period, the port of Hull developed, with the opening of Humber Dock in 1809 and Junction Dock (later Princes Dock) in 1829. By the time the agricultural industry began to recover, the carrs were in a bad state, but so was the Old Harbour at Hull. Holderness Drainage acted quickly, obtaining an Act of Parliament in 1832, which authorised the construction of a drain to Marfleet, where the outlet sluice (known locally as a clow) could be built at a lower level than previous outlets, thus providing a better gradient for the flow of the water. The old Main Drain was embanked where it crossed the carrs, and was used to carry runoff from the streams of Holderness to the Hull. The new lowland drain carried water from the carrs to Marfleet, passing under the upland drain in the Great Culvert. Where possible, old drains were made straighter, wider and deeper, and the meres in the Leven and Tickton area soon disappeared. By 1854, around one sixth of the land was still subject to occasional winter flooding, but most of the carrs were by then used for crops, rather than for pasture.[14]

Flooding in the Holderness Level increased between 1840 and 1880, as farmers used tile drains to keep their land free of standing water. These carried the water away more quickly to the main drains, increasing the peak flow. Where this drained into the upland drain, this was not a problem, but where it entered the lowland drain, it caused difficulties, particularly when Marfleet was tide locked. Following the successful introduction of steam pumping on the Beverley and Barmston drain, to the west of the River Hull, the Trustees looked at the possibility of installing pumps as Marfleet. However, help came from another source.[15]

The Alexandra Dock was built to the west of the final section of the drain in the early 1880s.[16] Research on the original Hull Dock had shown that around 1.25 million tons of mud were deposited in the dock each year, as a result of the muddy water of the Humber entering the dock for 2 to 3 hours at each high tide. In order to mitigate the high cost of dredging to remove this material, the water levels in the 46.5-acre (18.8 ha) dock were maintained by pumping fresh water from the Holderness Drain. Pumps capable of pumping 14.5 million cubic feet (410 Ml) per day were installed, resulting in significant savings in the cost of operating the dock.[17] Pumping from the drain increased again in 1913, when the newly constructed King George V Dock opened, and again required clean water. For Holderness Drainage, this provided the benefits of pumping without the cost.[18]

Holderness Drainage were responsible for the management of the system until 1930, when the Land Drainage Act 1930 became law. This organised the low-lying areas of England and Wales into catchment areas, each with its own catchment board. These boards were responsible for the main rivers within a catchment basin.[19] For the Holderness region, responsibility for the River Hull and the Holderness main drain passed to the Hull Catchment Board.[20] Holderness Drainage then became an internal drainage board (IDB), with responsibility for the smaller drains. Responsibility changed again with the passing of the River Boards Act 1948,[21] which created the Hull and East Yorkshire River Board. The next change occurred as a result of the Water Resources Act 1963, when the Hull River Board was joined to the Yorkshire Ouse River Board to become the Yorkshire Ouse and Hull River Authority.[22] Further amalgamation and reorganisation took place following the passing of the Water Act 1973, when the river authority became part of the much larger Yorkshire Water Authority.[23] Yorkshire Water Authority was privatised as a result of the Water Act 1989, and responsibility for main rivers including the Holderness Drain passed to the National Rivers Authority, which subsequently became part of the Environment Agency in 1995.[24]

Similarly, the internal drainage boards have gradually amalgamated into larger units. The Holderness IDB first merged with the Beverley IDB, and subsequently with the Beverley and Barmstom IDB, to become the Beverley and North Holderness IDB in 1981. They are responsible for an area of 91.98 square miles (238.2 km²) in which they maintain 163 miles (262 km) of drains, including those that feed into the Holderness Drain. Some 70 per cent of the area is dependent upon pumping stations to prevent flooding.[25]

Holderness Drain has three pumping stations along its length, which manage changes in level. The first is at Tickton, which was built in 1972 as part of the Holderness Drain scheme. The second is the Great Culvert pumping station, which was built at the same time. This is located close to the point of the original Great Culvert, which carried the high level drain to the River Hull over the low level drain to the Humber. Water from Monkdike and the Foredyke Stream was diverted into the low level drain, with the pumping station raising water from the remainder of the low level drain to the north. The rest of the Foredyke Stream, which carried the high level waters through the city to the River Hull at Stoneferry was abandoned.[26] The East Hull pumping station, near the outlet of the Holderness Drain, has a capacity of 94,600 cubic metres per hour (3,340,000 cu ft/h), and is jointly managed by Yorkshire Water and the Environment Agency.[27] It was originally constructed in 1949, so that the outflow from the drain could be pumped into the Humber when the level of the tides prevented gravity discharge. A major upgrade by Kingston upon Hull Corporation took place in May 1972, when it was extended to pump sewage flows into the Humber as well.[26]

In 2010, the Environment Agency looked at the costs and effectiveness of the pumping stations, and concluded that only East Hull significantly reduced the risk of flooding to properties. Costs to run Tickton pumping station were about £20,000 per year, and it was decided to continue operating it for a further five years, while working with local communities to find other sources of funding for it.[28] Although deemed uneconomic, Great Culvert pumping station would continue to be used, as removing it would result in water from the high level system flowing back up the Holderness Drain, increasing the risk of flooding.[29] At the time, a £900,000 refurbishment scheme was being carried out at East Hull pumping station, and ways to increase its capacity were under investigation.[30] Of the four pumps, the two 24-inch (61 cm) ones were refurbished first, followed by the two 48-inch (120 cm) ones.[31] All of the pumps have been available for pumping water from the drain since 2006, when pumping of sewage was discontinued following the commissioning of Saltend Waste Water Treatment Works,[32] and the 6.2-mile (10.0 km) deep level sewer that connects it to Hull's sewerage system.[33]

As part of a £28.5 million flood alleviation scheme for Hull, the Environment Agency decided that the East Hull pumping station had reached the end of its life, and that constructing a new pumping station would be more economical than refurbishing it. Following a planning decision in April 2020, work started on the new structure in May, which is located to the south of the existing station, nearer to the Humber. It will be capable of pumping 350 cubic feet per second (10 m³/s) in conditions where water levels in the drain are high and the tide in the Humber is also high. The Holderness Drain Flood Alleviation Scheme is a multi-agency project, jointly funded by the Environment Agency, Hull City Council, East Riding of Yorkshire Council, the Humber Local Enterprise Partnership and Highways England. Phase 2 of the project, to create a flood relief area to the east of Bransholme and Sutton near the Castle Monument, is expected to begin later in 2020.[34]

53.7422°N 0.2867°W / 53.7422; -0.2867