Prothrombin time

Vacutainer tube used for PT and PTT blood tests

Prothrombin time is typically analyzed by a laboratory technologist on an automated instrument at 37 °C (as a nominal approximation of normal human body temperature).

• Blood is drawn into a test tube containing liquid sodium citrate, which acts as an anticoagulant by binding the calcium in a sample. The blood is mixed, then centrifuged to separate blood cells from plasma (as prothrombin time is most commonly measured using blood plasma). In newborns, a capillary whole blood specimen is used.[2]
• A sample of the plasma is extracted from the test tube and placed into a measuring test tube (Note: for an accurate measurement, the ratio of blood to citrate needs to be fixed and should be labeled on the side of the measuring test tube by the manufacturing company; many laboratories will not perform the assay if the tube is underfilled and contains a relatively high concentration of citrate—the standardized dilution of 1 part anticoagulant to 9 parts whole blood is no longer valid).
• Next an excess of calcium (in a phospholipid suspension) is added to the test tube, thereby reversing the effects of citrate and enabling the blood to clot again.
• Finally, in order to activate the extrinsic / tissue factor clotting cascade pathway, tissue factor (also known as factor III) is added and the time the sample takes to clot is measured optically. Some laboratories use a mechanical measurement, which eliminates interferences from lipemic and icteric samples.

The prothrombin time ratio is the ratio of a subject's measured prothrombin time (in seconds) to the normal laboratory reference PT. The PT ratio varies depending on the specific reagents used, and has been replaced by the INR.[3] Elevated INR may be useful as a rapid and inexpensive diagnostic of infection in people with COVID-19.[4]

The result (in seconds) for a prothrombin time performed on a normal individual will vary according to the type of analytical system employed. This is due to the variations between different types and batches of manufacturer's tissue factor used in the reagent to perform the test. The INR was devised to standardize the results. Each manufacturer assigns an ISI value (International Sensitivity Index) for any tissue factor they manufacture. The ISI value indicates how a particular batch of tissue factor compares to an international reference tissue factor. The ISI is usually between 0.94 and 1.4 for more sensitive and 2.0–3.0 for less sensitive thromboplastins.[5][6][7]

The INR is the ratio of a patient's prothrombin time to a normal (control) sample, raised to the power of the ISI value for the analytical system being used.

${\displaystyle {\text{INR}}=\left({\frac {{\text{PT}}_{\text{test}}}{{\text{PT}}_{\text{normal}}}}\right)^{\text{ISI}}}$

PT_normal is established as the geometric mean of the prothrombin times (PT) of a reference sample group.[8]

The prothrombin time is the time it takes plasma to clot after addition of tissue factor (obtained from animals such as rabbits, or recombinant tissue factor, or from brains of autopsy patients). This measures the quality of the extrinsic pathway (as well as the common pathway) of coagulation. The speed of the extrinsic pathway is greatly affected by levels of functional factor VII in the body. Factor VII has a short half-life and the carboxylation of its glutamate residues requires vitamin K. The prothrombin time can be prolonged as a result of deficiencies in vitamin K, warfarin therapy, malabsorption, or lack of intestinal colonization by bacteria (such as in newborns). In addition, poor factor VII synthesis (due to liver disease) or increased consumption (in disseminated intravascular coagulation) may prolong the PT.

The INR is typically used to monitor patients on warfarin or related oral anticoagulant therapy. The normal range for a healthy person not using warfarin is 0.8–1.2, and for people on warfarin therapy an INR of 2.0–3.0 is usually targeted, although the target INR may be higher in particular situations, such as for those with a mechanical heart valve. If the INR is outside the target range, a high INR indicates a higher risk of bleeding, while a low INR suggests a higher risk of developing a clot. In patients on a vitamin K antagonist such as warfarin with supratherapeutic INR but INR less than 10 and no bleeding, it is enough to lower the dose or omit a dose, monitor the INR and resume the vitamin K antagonist at an adjusted lower dose when the target INR is reached.[9] For people who need rapid reversal of the vitamin K antagonist – such as due to serious bleeding – or who need emergency surgery, the effects of warfarin can be reversed with vitamin K, prothrombin complex concentrate (PCC), or fresh frozen plasma (FFP).[10]

Lupus anticoagulant, a circulating inhibitor predisposing for thrombosis, may skew PT results, depending on the assay used.[11] Variations between various thromboplastin preparations have in the past led to decreased accuracy of INR readings, and a 2005 study suggested that despite international calibration efforts (by INR) there were still statistically significant differences between various kits,[12] casting doubt on the long-term tenability of PT/INR as a measure for anticoagulant therapy.[13] Indeed, a new prothrombin time variant, the Fiix prothrombin time, intended solely for monitoring warfarin and other vitamin K antagonists has been invented[14] and recently become available as a manufactured test. The Fiix prothrombin time is only affected by reductions in factor II and/or factor X and this stabilizes the anticoagulant effect and appears to improve clinical outcome according to an investigator initiated randomized blinded clinical trial, The Fiix-trial.[15] In this trial thromboembolism was reduced by 50% during long-term treatment and despite that bleeding was not increased.

International guidelines were published in 2005 to govern home monitoring of oral anticoagulation by the International Self-Monitoring Association for Oral Anticoagulation.[20] The international guidelines study stated, "The consensus agrees that patient self-testing and patient self-management are effective methods of monitoring oral anticoagulation therapy, providing outcomes at least as good as, and possibly better than, those achieved with an anticoagulation clinic. All patients must be appropriately selected and trained. Currently, available self-testing/self-management devices give INR results which are comparable with those obtained in laboratory testing."

Medicare coverage for home testing of INR has been expanded in order to allow more people access to home testing of INR in the US. The release on 19 March 2008 said, "[t]he Centers for Medicare & Medicaid Services (CMS) expanded Medicare coverage for home blood testing of prothrombin time (PT) International Normalized Ratio (INR) to include beneficiaries who are using the drug warfarin, an anticoagulant (blood thinner) medication, for chronic atrial fibrillation or venous thromboembolism." In addition, "those Medicare beneficiaries and their physicians managing conditions related to chronic atrial fibrillation or venous thromboembolism will benefit greatly through the use of the home test."[21]