Radiation pressure

According to Maxwell's theory of electromagnetism, an electromagnetic wave carries momentum, which will be transferred to an opaque surface it strikes.

The energy flux (irradiance) of a plane wave is calculated using the Poynting vector ${\displaystyle \mathbf {S} =\mathbf {E} \times \mathbf {H} }$, whose magnitude we denote by S. S divided by the speed of light is the density of the linear momentum per unit area (pressure) of the electromagnetic field. So, dimensionally, the Poynting vector is S = power/area = rate of doing work/area = ΔF/Δt Δx/area, which is the speed of light, c = Δx / Δt, times pressure, ΔF / area. That pressure is experienced as radiation pressure on the surface:

$${\displaystyle P_{\text{incident}}={\frac {\langle S\rangle }{c}}={\frac {I_{f}}{c}}}$$

where ${\displaystyle P}$ is pressure (usually in Pascals), ${\displaystyle I_{f}}$ is the incident irradiance (usually in W/m²) and ${\displaystyle c}$ is the speed of light in vacuum. Here, 1/c ≈ 3.34 N/GW.

If the surface is planar at an angle α to the incident wave, the intensity across the surface will be geometrically reduced by the cosine of that angle and the component of the radiation force against the surface will also be reduced by the cosine of α, resulting in a pressure:

$${\displaystyle P_{\text{incident}}={\frac {I_{f}}{c}}\cos ^{2}\alpha }$$

The momentum from the incident wave is in the same direction of that wave. But only the component of that momentum normal to the surface contributes to the pressure on the surface, as given above. The component of that force tangent to the surface is not called pressure.[12]

The above treatment for an incident wave accounts for the radiation pressure experienced by a black (totally absorbing) body. If the wave is specularly reflected, then the recoil due to the reflected wave will further contribute to the radiation pressure. In the case of a perfect reflector, this pressure will be identical to the pressure caused by the incident wave:

$${\displaystyle P_{\text{emitted}}={\frac {I_{f}}{c}}}$$

thus doubling the net radiation pressure on the surface:

$${\displaystyle P_{\text{net}}=P_{\text{incident}}+P_{\text{emitted}}=2{\frac {I_{f}}{c}}}$$

For a partially reflective surface, the second term must be multiplied by the reflectivity (also known as reflection coefficient of intensity), so that the increase is less than double. For a diffusely reflective surface, the details of the reflection and geometry must be taken into account, again resulting in an increased net radiation pressure of less than double.

Just as a wave reflected from a body contributes to the net radiation pressure experienced, a body that emits radiation of its own (rather than reflected) obtains a radiation pressure again given by the irradiance of that emission in the direction normal to the surface I_e:

$${\displaystyle P_{\text{emitted}}={\frac {I_{\text{e}}}{c}}}$$

The emission can be from black-body radiation or any other radiative mechanism. Since all materials emit black-body radiation (unless they are totally reflective or at absolute zero), this source for radiation pressure is ubiquitous but usually tiny. However, because black-body radiation increases rapidly with temperature (as the fourth power of temperature, given by the Stefan–Boltzmann law), radiation pressure due to the temperature of a very hot object (or due to incoming black-body radiation from similarly hot surroundings) can become significant. This is important in stellar interiors.

Electromagnetic radiation can be viewed in terms of particles rather than waves; these particles are known as photons. Photons do not have a rest-mass; however, photons are never at rest (they move at the speed of light) and acquire a momentum nonetheless which is given by:

$${\displaystyle p={\dfrac {h}{\lambda }}={\frac {E_{p}}{c}},}$$

where p is momentum, h is Planck's constant, λ is wavelength, and c is speed of light in vacuum. And E_p is the energy of a single photon given by:

$${\displaystyle E_{p}=h\nu ={\frac {hc}{\lambda }}}$$

The radiation pressure again can be seen as the transfer of each photon's momentum to the opaque surface, plus the momentum due to a (possible) recoil photon for a (partially) reflecting surface. Since an incident wave of irradiance I_f over an area A has a power of I_fA, this implies a flux of I_f/E_p photons per second per unit area striking the surface. Combining this with the above expression for the momentum of a single photon, results in the same relationships between irradiance and radiation pressure described above using classical electromagnetics. And again, reflected or otherwise emitted photons will contribute to the net radiation pressure identically.

In general, the pressure of electromagnetic waves can be obtained from the vanishing of the trace of the electromagnetic stress tensor: since this trace equals 3P − u, we get

$${\displaystyle P={\frac {u}{3}},}$$

where u is the radiation energy per unit volume.

This can also be shown in the specific case of the pressure exerted on surfaces of a body in thermal equilibrium with its surroundings, at a temperature T: the body will be surrounded by a uniform radiation field described by the Planck black-body radiation law and will experience a compressive pressure due to that impinging radiation, its reflection, and its own black-body emission. From that it can be shown that the resulting pressure is equal to one third of the total radiant energy per unit volume in the surrounding space.[13][14][15][16]

By using Stefan–Boltzmann law, this can be expressed as

$${\displaystyle P_{\text{compress}}={\frac {u}{3}}={\frac {4\sigma }{3c}}T^{4},}$$

where ${\displaystyle \sigma }$ is the Stefan–Boltzmann constant.

Solar radiation pressure at the Earth's distance from the Sun, may be calculated by dividing the solar constant G_SC (above) by the speed of light c. For an absorbing sheet facing the Sun, this is simply:[18]

$${\displaystyle P={\frac {G_{\text{SC}}}{c}}\approx 4.5\cdot 10^{-6}~{\text{Pa}}=4.5~\mu {\text{Pa}}.}$$

This result is in pascals, equivalent to N/m² (newtons per square meter). For a sheet at an angle α to the Sun, the effective area A of a sheet is reduced by a geometrical factor resulting in a force in the direction of the sunlight of:

$${\displaystyle F={\frac {G_{\text{SC}}}{c}}(A\cos \alpha ).}$$

To find the component of this force normal to the surface, another cosine factor must be applied resulting in a pressure P on the surface of:

$${\displaystyle P={\frac {F}{A}}={\frac {G_{\text{SC}}}{c}}\cos ^{2}\alpha .}$$

Note, however, that in order to account for the net effect of solar radiation on a spacecraft for instance, one would need to consider the total force (in the direction away from the Sun) given by the preceding equation, rather than just the component normal to the surface that we identify as "pressure".

The solar constant is defined for the Sun's radiation at the distance to the Earth, also known as one astronomical unit (au). Consequently, at a distance of R astronomical units (R thus being dimensionless), applying the inverse-square law, we would find:

$${\displaystyle P={\frac {G_{\text{SC}}}{cR^{2}}}\cos ^{2}\alpha .}$$

Finally, considering not an absorbing but a perfectly reflecting surface, the pressure is doubled due to the reflected wave, resulting in:

$${\displaystyle P=2{\frac {G_{\text{SC}}}{cR^{2}}}\cos ^{2}\alpha .}$$

Note that unlike the case of an absorbing material, the resulting force on a reflecting body is given exactly by this pressure acting normal to the surface, with the tangential forces from the incident and reflecting waves canceling each other. In practice, materials are neither totally reflecting nor totally absorbing, so the resulting force will be a weighted average of the forces calculated using these formulas.

Solar radiation pressure is a source of orbital perturbations. It significantly affects the orbits and trajectories of small bodies including all spacecraft.

Solar radiation pressure affects bodies throughout much of the Solar System. Small bodies are more affected than large ones because of their lower mass relative to their surface area. Spacecraft are affected along with natural bodies (comets, asteroids, dust grains, gas molecules).

The radiation pressure results in forces and torques on the bodies that can change their translational and rotational motions. Translational changes affect the orbits of the bodies. Rotational rates may increase or decrease. Loosely aggregated bodies may break apart under high rotation rates. Dust grains can either leave the Solar System or spiral into the Sun.[19]

A whole body is typically composed of numerous surfaces that have different orientations on the body. The facets may be flat or curved. They will have different areas. They may have optical properties differing from other aspects.

At any particular time, some facets are exposed to the Sun, and some are in shadow. Each surface exposed to the Sun is reflecting, absorbing, and emitting radiation. Facets in shadow are emitting radiation. The summation of pressures across all of the facets defines the net force and torque on the body. These can be calculated using the equations in the preceding sections.[12][18]

The Yarkovsky effect affects the translation of a small body. It results from a face leaving solar exposure being at a higher temperature than a face approaching solar exposure. The radiation emitted from the warmer face is more intense than that of the opposite face, resulting in a net force on the body that affects its motion.[20]

The YORP effect is a collection of effects expanding upon the earlier concept of the Yarkovsky effect, but of a similar nature. It affects the spin properties of bodies.

The Poynting–Robertson effect applies to grain-size particles. From the perspective of a grain of dust circling the Sun, the Sun's radiation appears to be coming from a slightly forward direction (aberration of light). Therefore, the absorption of this radiation leads to a force with a component against the direction of movement. (The angle of aberration is tiny, since the radiation is moving at the speed of light, while the dust grain is moving many orders of magnitude slower than that.) The result is a gradual spiral of dust grains into the Sun. Over long periods of time, this effect cleans out much of the dust in the Solar System.

While rather small in comparison to other forces, the radiation pressure force is inexorable. Over long periods of time, the net effect of the force is substantial. Such feeble pressures can produce marked effects upon minute particles like gas ions and electrons, and are essential in the theory of electron emission from the Sun, of cometary material, and so on.

Because the ratio of surface area to volume (and thus mass) increases with decreasing particle size, dusty (micrometre-size) particles are susceptible to radiation pressure even in the outer Solar System. For example, the evolution of the outer rings of Saturn is significantly influenced by radiation pressure.

As a consequence of light pressure, Einstein[21] in 1909 predicted the existence of "radiation friction", which would oppose the movement of matter. He wrote: "radiation will exert pressure on both sides of the plate. The forces of pressure exerted on the two sides are equal if the plate is at rest. However, if it is in motion, more radiation will be reflected on the surface that is ahead during the motion (front surface) than on the back surface. The backward acting force of pressure exerted on the front surface is thus larger than the force of pressure acting on the back. Hence, as the resultant of the two forces, there remains a force that counteracts the motion of the plate and that increases with the velocity of the plate. We will call this resultant 'radiation friction' in brief."

Solar sailing, an experimental method of spacecraft propulsion, uses radiation pressure from the Sun as a motive force. The idea of interplanetary travel by light was mentioned by Jules Verne in his 1865 novel From the Earth to the Moon.

A sail reflects about 90% of the incident radiation. The 10% that is absorbed is radiated away from both surfaces, with the proportion emitted from the unlit surface depending on the thermal conductivity of the sail. A sail has curvature, surface irregularities, and other minor factors that affect its performance.

The Japan Aerospace Exploration Agency (JAXA) has successfully unfurled a solar sail in space, which has already succeeded in propelling its payload with the IKAROS project.

The photon epoch is a phase when the energy of the universe was dominated by photons, between 10 seconds and 380,000 years after the Big Bang.[23]

The Pillars of Creation clouds within the Eagle Nebula shaped by radiation pressure and stellar winds.

The process of galaxy formation and evolution began early in the history of the cosmos. Observations of the early universe strongly suggest that objects grew from bottom-up (i.e., smaller objects merging to form larger ones). As stars are thereby formed and become sources of electromagnetic radiation, radiation pressure from the stars becomes a factor in the dynamics of remaining circumstellar material.[24]

The gravitational compression of clouds of dust and gases is strongly influenced by radiation pressure, especially when the condensations lead to star births. The larger young stars forming within the compressed clouds emit intense levels of radiation that shift the clouds, causing either dispersion or condensations in nearby regions, which influences birth rates in those nearby regions.

Stars predominantly form in regions of large clouds of dust and gases, giving rise to star clusters. Radiation pressure from the member stars eventually disperses the clouds, which can have a profound effect on the evolution of the cluster.

Many open clusters are inherently unstable, with a small enough mass that the escape velocity of the system is lower than the average velocity of the constituent stars. These clusters will rapidly disperse within a few million years. In many cases, the stripping away of the gas from which the cluster formed by the radiation pressure of the hot young stars reduces the cluster mass enough to allow rapid dispersal.

A protoplanetary disk with a cleared central region (artist's conception).

Star formation is the process by which dense regions within molecular clouds in interstellar space collapse to form stars. As a branch of astronomy, star formation includes the study of the interstellar medium and giant molecular clouds (GMC) as precursors to the star formation process, and the study of protostars and young stellar objects as its immediate products. Star formation theory, as well as accounting for the formation of a single star, must also account for the statistics of binary stars and the initial mass function.

Planetary systems are generally believed to form as part of the same process that results in star formation. A protoplanetary disk forms by gravitational collapse of a molecular cloud, called a solar nebula, and then evolves into a planetary system by collisions and gravitational capture. Radiation pressure can clear a region in the immediate vicinity of the star. As the formation process continues, radiation pressure continues to play a role in affecting the distribution of matter. In particular, dust and grains can spiral into the star or escape the stellar system under the action of radiation pressure.

Comet Hale–Bopp (C/1995 O1). Radiation pressure and solar wind effects on the dust and gas tails are clearly seen.

In stellar interiors the temperatures are very high. Stellar models predict a temperature of 15 MK in the center of the Sun, and at the cores of supergiant stars the temperature may exceed 1 GK. As the radiation pressure scales as the fourth power of the temperature, it becomes important at these high temperatures. In the Sun, radiation pressure is still quite small when compared to the gas pressure. In the heaviest non-degenerate stars, radiation pressure is the dominant pressure component.[25]

Solar radiation pressure strongly affects comet tails. Solar heating causes gases to be released from the comet nucleus, which also carry away dust grains. Radiation pressure and solar wind then drive the dust and gases away from the Sun's direction. The gases form a generally straight tail, while slower moving dust particles create a broader, curving tail.

Lasers can be used as a source of monochromatic light with wavelength ${\displaystyle \lambda }$. With a set of lenses, one can focus the laser beam to a point that is ${\displaystyle \lambda }$ in diameter (or ${\displaystyle r=\lambda /2}$).

The radiation pressure of a P = 30 mW laser with λ = 1064 nm can therefore be computed as follows.

Area:

$${\displaystyle A=\pi \left({\frac {\lambda }{2}}\right)^{2}\approx 10^{-12}{\text{ m}}^{2},}$$

force:

$${\displaystyle F={\frac {P}{c}}={\frac {30{\text{ mW}}}{299792458{\text{ m/s}}}}\approx 10^{-10}{\text{ N}},}$$

pressure:

$${\displaystyle p={\frac {F}{A}}\approx {\frac {10^{-10}{\text{ N}}}{10^{-12}{\text{ m}}^{2}}}=100{\text{ Pa}}.}$$

This is used to trap or levitate particles in optical tweezers.

In this optomechanical cavity, light is trapped and enhanced between two mirrors. One of the mirrors is attached to a spring and can move. The radiation pressure force of the light circulating in the cavity can damp or amplify the oscillation of the mirror on the spring.

The reflection of a laser pulse from the surface of an elastic solid can give rise to various types of elastic waves that propagate inside the solid or liquid. In other words, the light can excite and/or amplify motion of, and in, materials. This is the subject of study in the field of optomechanics. The weakest waves are generally those that are generated by the radiation pressure acting during the reflection of the light. Such light-pressure-induced elastic waves have for example observed inside an ultrahigh-reflectivity dielectric mirror.[26] These waves are the most basic fingerprint of a light-solid matter interaction on the macroscopic scale.[27] In the field of cavity optomechanics, light is trapped and resonantly enhanced in optical cavities, for example between mirrors. This serves the purpose of gravely enhancing the power of the light, and the radiation pressure it can exert on objects and materials. Optical control (that is, manipulation of the motion) of a plethora of objects has been realized: from kilometers long beams (such as in the LIGO interferometer)[28] to clouds of atoms,[29] and from micro-engineered trampolines[30] to superfluids.[31][32]

Opposite to exciting or amplifying motion, light can also damp the motion of objects. Laser cooling is a method of cooling materials very close to absolute zero by converting some of material's motional energy into light. Kinetic energy and thermal energy of the material are synonyms here, because they represent the energy associated with Brownian motion of the material. Atoms traveling towards a laser light source perceive a doppler effect tuned to the absorption frequency of the target element. The radiation pressure on the atom slows movement in a particular direction until the Doppler effect moves out of the frequency range of the element, causing an overall cooling effect.[34]

An other active research area of laser–matter interaction is the radiation pressure acceleration of ions or protons from thin–foil targets.[35] High ion energy beams can be generated for medical applications (for example in ion beam therapy[36]) by the radiation pressure of short laser pulses on ultra-thin foils.