Macaulay's method

The starting point is the relation from Euler-Bernoulli beam theory

${\displaystyle \pm EI{\dfrac {d^{2}w}{dx^{2}}}=M}$

Where ${\displaystyle w}$ is the deflection and ${\displaystyle M}$ is the bending moment. This equation[7] is simpler than the fourth-order beam equation and can be integrated twice to find ${\displaystyle w}$ if the value of ${\displaystyle M}$ as a function of ${\displaystyle x}$ is known. For general loadings, ${\displaystyle M}$ can be expressed in the form

${\displaystyle M=M_{1}(x)+P_{1}\langle x-a_{1}\rangle +P_{2}\langle x-a_{2}\rangle +P_{3}\langle x-a_{3}\rangle +\dots }$

where the quantities ${\displaystyle P_{i}\langle x-a_{i}\rangle }$ represent the bending moments due to point loads and the quantity ${\displaystyle \langle x-a_{i}\rangle }$ is a Macaulay bracket defined as

${\displaystyle \langle x-a_{i}\rangle ={\begin{cases}0&\mathrm {if} ~x<a_{i}\\x-a_{i}&\mathrm {if} ~x>a_{i}\end{cases}}}$

Ordinarily, when integrating ${\displaystyle P(x-a)}$ we get

${\displaystyle \int P(x-a)~dx=P\left[{\cfrac {x^{2}}{2}}-ax\right]+C}$

However, when integrating expressions containing Macaulay brackets, we have

${\displaystyle \int P\langle x-a\rangle ~dx=P{\cfrac {\langle x-a\rangle ^{2}}{2}}+C_{m}}$

with the difference between the two expressions being contained in the constant ${\displaystyle C_{m}}$. Using these integration rules makes the calculation of the deflection of Euler-Bernoulli beams simple in situations where there are multiple point loads and point moments. The Macaulay method predates more sophisticated concepts such as Dirac delta functions and step functions but achieves the same outcomes for beam problems.

Simply supported beam with a single eccentric concentrated load.

An illustration of the Macaulay method considers a simply supported beam with a single eccentric concentrated load as shown in the adjacent figure. The first step is to find ${\displaystyle M}$. The reactions at the supports A and C are determined from the balance of forces and moments as

${\displaystyle R_{A}+R_{C}=P,~~LR_{C}=Pa}$

Therefore, ${\displaystyle R_{A}=Pb/L}$ and the bending moment at a point D between A and B (${\displaystyle 0<x<a}$) is given by

${\displaystyle M=R_{A}x=Pbx/L}$

Using the moment-curvature relation and the Euler-Bernoulli expression for the bending moment, we have

${\displaystyle EI{\dfrac {d^{2}w}{dx^{2}}}={\dfrac {Pbx}{L}}}$

Integrating the above equation we get, for ${\displaystyle 0<x<a}$,

${\displaystyle {\begin{aligned}EI{\dfrac {dw}{dx}}&={\dfrac {Pbx^{2}}{2L}}+C_{1}&&\quad \mathrm {(i)} \\EIw&={\dfrac {Pbx^{3}}{6L}}+C_{1}x+C_{2}&&\quad \mathrm {(ii)} \end{aligned}}}$

At ${\displaystyle x=a_{-}}$

${\displaystyle {\begin{aligned}EI{\dfrac {dw}{dx}}(a_{-})&={\dfrac {Pba^{2}}{2L}}+C_{1}&&\quad \mathrm {(iii)} \\EIw(a_{-})&={\dfrac {Pba^{3}}{6L}}+C_{1}a+C_{2}&&\quad \mathrm {(iv)} \end{aligned}}}$

For a point D in the region BC (${\displaystyle a<x<L}$), the bending moment is

${\displaystyle M=R_{A}x-P(x-a)=Pbx/L-P(x-a)}$

In Macaulay's approach we use the Macaulay bracket form of the above expression to represent the fact that a point load has been applied at location B, i.e.,

${\displaystyle M={\frac {Pbx}{L}}-P\langle x-a\rangle }$

Therefore, the Euler-Bernoulli beam equation for this region has the form

${\displaystyle EI{\dfrac {d^{2}w}{dx^{2}}}={\dfrac {Pbx}{L}}-P\langle x-a\rangle }$

Integrating the above equation, we get for ${\displaystyle a<x<L}$

${\displaystyle {\begin{aligned}EI{\dfrac {dw}{dx}}&={\dfrac {Pbx^{2}}{2L}}-P{\cfrac {\langle x-a\rangle ^{2}}{2}}+D_{1}&&\quad \mathrm {(v)} \\EIw&={\dfrac {Pbx^{3}}{6L}}-P{\cfrac {\langle x-a\rangle ^{3}}{6}}+D_{1}x+D_{2}&&\quad \mathrm {(vi)} \end{aligned}}}$

At ${\displaystyle x=a_{+}}$

${\displaystyle {\begin{aligned}EI{\dfrac {dw}{dx}}(a_{+})&={\dfrac {Pba^{2}}{2L}}+D_{1}&&\quad \mathrm {(vii)} \\EIw(a_{+})&={\dfrac {Pba^{3}}{6L}}+D_{1}a+D_{2}&&\quad \mathrm {(viii)} \end{aligned}}}$

Comparing equations (iii) & (vii) and (iv) & (viii) we notice that due to continuity at point B, ${\displaystyle C_{1}=D_{1}}$ and ${\displaystyle C_{2}=D_{2}}$. The above observation implies that for the two regions considered, though the equation for bending moment and hence for the curvature are different, the constants of integration got during successive integration of the equation for curvature for the two regions are the same.

The above argument holds true for any number/type of discontinuities in the equations for curvature, provided that in each case the equation retains the term for the subsequent region in the form ${\displaystyle \langle x-a\rangle ^{n},\langle x-b\rangle ^{n},\langle x-c\rangle ^{n}}$ etc. It should be remembered that for any x, giving the quantities within the brackets, as in the above case, -ve should be neglected, and the calculations should be made considering only the quantities which give +ve sign for the terms within the brackets.

Reverting to the problem, we have

${\displaystyle EI{\dfrac {d^{2}w}{dx^{2}}}={\dfrac {Pbx}{L}}-P\langle x-a\rangle }$

It is obvious that the first term only is to be considered for ${\displaystyle x<a}$ and both the terms for ${\displaystyle x>a}$ and the solution is

${\displaystyle {\begin{aligned}EI{\dfrac {dw}{dx}}&=\left[{\dfrac {Pbx^{2}}{2L}}+C_{1}\right]-{\cfrac {P\langle x-a\rangle ^{2}}{2}}\\EIw&=\left[{\dfrac {Pbx^{3}}{6L}}+C_{1}x+C_{2}\right]-{\cfrac {P\langle x-a\rangle ^{3}}{6}}\end{aligned}}}$

Note that the constants are placed immediately after the first term to indicate that they go with the first term when ${\displaystyle x<a}$ and with both the terms when ${\displaystyle x>a}$. The Macaulay brackets help as a reminder that the quantity on the right is zero when considering points with ${\displaystyle x<a}$.

• Beam theory
• Bending
• Bending moment
• Singularity function
• Shear and moment diagram
• Timoshenko beam theory