Mercedes-Benz M180 engine

The original M180 engine was rated at 80 PS (59 kW). It powered the W187 220 sedan, coupé, and cabriolet (Type A and B) from 1951 to 1955, the W180 220a sedan, coupé, and cabriolet from 1954 to 1956 and the W105 219 4-door sedan from 1956 to 1959.

It also powered the Unimog 404, a military version of the Unimog, which was built from 1955 until 1980.

The W180 Ponton 220S Sedan, Coupe and Cabriolet of 1956-1959 benefited from the up-rated M180.924 which delivered 124 hp (92 kW; 126 PS). In 1958 Bosch mechanical fuel injection was added to the 2.2-litre six and the engine, now giving 113–134 bhp (84–100 kW; 115–136 PS), was redesignated M127. The M127 was fitted to the last of the Pontons: the rare 1958 W128 220SE, of which fewer than 4000 were produced.

In 1959 the first series of W111 "Fintail" 220SE and 220SEb models was introduced, with the carburetted M180 in the 220b and 220Sb and the M127 used in the 220SEb. The addition of the lower case ‘b’ was added to differentiate the Fintails from the earlier Pontons.

In 1965 the W111/W112 sedans were superseded by the new W108/109 series 250 and 250S (apart from the W111 230/230S, produced from 1965 to 1968). The M180 was bored by 2 mm (0.079 in), creating an bore × stroke of 82 mm × 72.8 mm (3.23 in × 2.87 in) and displacement of 2.3 L; 140.8 cu in (2,307 cc). All models received the new 2.3 L engine.

and M108

The M180's stroke was increased to produce the 2.5 L engine for the new Mercedes-Benz W108 250S and 250SE. A 6 mm (0.24 in) increase resulted in a bore × stroke of 82 mm × 78.8 mm (3.23 in × 3.10 in) and displacement of 2.5 L; 152.3 cu in (2,496 cc), carburetted on the 250S and fuel-injected on the 250SE, designated the M129. The M129 was fitted with a mechanically controlled six-piston fuel injection pump. A change from four to seven main bearings was necessary in order smoothly to handle the resulting increase in power. A larger capacity oil pump was also specified. Connecting rods were slightly shortened, reflecting the 6 mm (0.24 in) longer stroke in a block of unchanged overall height. The redesigned cylinder heads incorporated larger ports, and the valve diameters were increased by 2 mm (0.079 in). On the fuel injected cars a six-plunger pump replaced the previous car's two plunger pump and the injectors were repositioned to give a more direct angle towards the inlet valve heads. The engine cooling fan now had six blades instead of four and incorporated a viscous coupling which activated the fan only when engine speed exceeded 3,000 rpm or the radiator water temperature reached a preset limit. The engine of the 250 S was called M108 (for W108 chassis) and only the 250 SE engine was designated M129.

In 1968 the ‘New Generation’ or /8 models were introduced, along with a change to the venerable mid-size six. The M180 engine of the 230/230S was continued in the W114 230 and 230.6, while the M180 of the 250S underwent a few changes and was renamed the M114. This was also available with Bosch D-Jetronic fuel injection, as fitted to the 250CE.

In 1968 the 2.5L M129 of the 250SE was superseded by the 2.8L M130, the ultimate variant of the mid-sized six, obtained by increasing the bore by 4.5 mm (0.18 in). The result was a bore × stroke of 86.5 mm × 78.8 mm (3.41 in × 3.10 in); 2,778 cc (2.8 L; 169.5 cu in)), the maximum practical enlargement of the engine given the limitations of the block, which required deletion of water passages between the cylinders. It was used in the W108 280S and 280SE, in the W109 300SEL from December 1967 to January 1970, and in the W113 280SL.

The final incarnation of the M180 line of engines was the 2.5L M123, fitted with the notorious Solex four-barrel carburetor in the W123 chassis 250 produced between 1975 and 1985.