Cardinal point (optics)

The front focal point of an optical system, by definition, has the property that any ray that passes through it will emerge from the system parallel to the optical axis. The rear (or back) focal point of the system has the reverse property: rays that enter the system parallel to the optical axis are focused such that they pass through the rear focal point.

Rays that leave the object with the same angle cross at the back focal plane.

The front and rear (or back) focal planes are defined as the planes, perpendicular to the optic axis, which pass through the front and rear focal points. An object infinitely far from the optical system forms an image at the rear focal plane. For an object at a finite distance, the image is formed at a different location, but rays that leave the object parallel to one another cross at the rear focal plane.

Angle filtering with an aperture at the rear focal plane.

A diaphragm or "stop" at the rear focal plane of a lens can be used to filter rays by angle, since an aperture centred on the optical axis there will only pass rays that were emitted from the object at a sufficiently small angle from the optical axis. Using a sufficiently small aperture in the rear focal plane will make the lens object-space telecentric.

Similarly, the allowed range of angles on the output side of the lens can be filtered by putting an aperture at the front focal plane of the lens (or a lens group within the overall lens), and a sufficiently small aperture will make the lens image-space telecentric. This is important for DSLR cameras having CCD sensors. The pixels in these sensors are more sensitive to rays that hit them straight on than to those that strike at an angle. A lens that does not control the angle of incidence at the detector will produce pixel vignetting in the images.

Various lens shapes, and the location of the principal planes H and H' for each. The radii of curvature of the lens surfaces are indicated as r₁ and r₂.

The two principal planes of a lens have the property that a ray emerging from the lens appears to have crossed the rear principal plane at the same distance from the optical axis that the ray appeared to have crossed the front principal plane, as viewed from the front of the lens. This means that the lens can be treated as if all of the refraction happened at the principal planes, and rays travel parallel to the optical axis between the planes. (Linear magnification between the principal planes is +1.) The principal planes are crucial in defining the properties of an optical system, since the magnification of the system is determined by the distance from an object to the front principal plane and the distance from the rear principal plane to the object's image. The principal points are the points where the principal planes cross the optical axis.

If the medium surrounding an optical system has a refractive index of 1 (e.g., air or vacuum), then the distance from each principal plane to the corresponding focal point is just the focal length of the system. In the more general case, the distance to the foci is the focal length multiplied by the index of refraction of the medium.

For a thin lens in air, the principal planes both lie at the location of the lens. The point where they cross the optical axis is sometimes misleadingly called the optical centre of the lens. Note, however, that for a real lens the principal planes do not necessarily pass through the centre of the lens, and in general may not lie inside the lens at all.

N, N' The front and rear nodal points of a thick lens.

The front and rear nodal points of a lens have the property that a ray aimed at one of them will be refracted by the lens such that it appears to have come from the other with the same angle to the optical axis. (Angular magnification between nodal points is +1.) The nodal points therefore do for angles what the principal planes do for transverse distance. If the medium on both sides of an optical system is the same (e.g., air or vacuum), then the front and rear nodal points coincide with the front and rear principal points, respectively.

The nodal points were first described by Johann Listing in 1845 to evaluate the human eye, where the image is formed in fluid. Over time it was found that if a line was drawn through the posterior apex of the crystalline lens at the visual angle of a distant object, then it would point to the image location on the retina, even for very large angles.[4][5] This line passes approximately through the 2nd nodal point, but rather than being an actual paraxial ray, it identifies the image formed by ray bundles that pass through the centre of the pupil. This can be used to find the magnification, or to scale retinal locations. This extends the use of the nodal point for the eye, but the imaging properties come from the cornea and retina being highly curved, rather than paraxial properties, and this is rarely clear in publications.

The nodal points are widely misunderstood in photography, where it is commonly asserted that the light rays "intersect" at "the nodal point", that the iris diaphragm of the lens is located there, and that this is the correct pivot point for panoramic photography, so as to avoid parallax error.[6][7][8] These claims generally arise from confusion about the optics of camera lenses, as well as confusion between the nodal points and the other cardinal points of the system. (A better choice of the point about which to pivot a camera for panoramic photography can be shown to be the centre of the system's entrance pupil.[6][7][8] On the other hand, swing-lens cameras with fixed film position rotate the lens about the rear nodal point to stabilize the image on the film.[8][9])

In optics, surface vertices are the points where each optical surface crosses the optical axis. They are important primarily because they are physically measurable parameters for the optical element positions, and so the positions of the cardinal points of the optical system must be known with respect to the surface vertices to describe the system.

In anatomy, the surface vertices of the eye's lens are called the anterior and posterior poles of the lens.[10]

An optical system is rotationally symmetric if its imaging properties are unchanged by any rotation about some axis. This (unique) axis of rotational symmetry is the optical axis of the system. Optical systems can be folded using plane mirrors; the system is still considered to be rotationally symmetric if it possesses rotational symmetry when unfolded. Any point on the optical axis (in any space) is an axial point.

Rotational symmetry greatly simplifies the analysis of optical systems, which otherwise must be analyzed in three dimensions. Rotational symmetry allows the system to be analyzed by considering only rays confined to a single transverse plane containing the optical axis. Such a plane is called a meridional plane; it is a cross-section through the system.

An ideal, rotationally symmetric, optical imaging system must meet three criteria:

1. All rays "originating" from each object point converge to a single and unique image point (Imaging is stigmatic).
2. Object planes perpendicular to the optical axis are conjugate to image planes perpendicular to the axis.
3. The image of an object confined to a plane normal to the axis is geometrically similar to the object.

In some optical systems imaging is stigmatic for one or perhaps a few object points, but to be an ideal system imaging must be stigmatic for every object point. In an ideal system, every object point maps to a different image point.

Unlike rays in mathematics, optical rays extend to infinity in both directions. Rays are real when they are in the part of the optical system to which they apply, and are virtual elsewhere. For example, object rays are real on the object side of the optical system, while image rays are real on the image side of the system. In stigmatic imaging, an object ray intersecting any specific point in object space must be conjugate to an image ray intersecting the conjugate point in image space. A consequence is that every point on an object ray is conjugate to some point on the conjugate image ray.

Geometrical similarity implies the image is a scale model of the object. There is no restriction on the image's orientation; the image may be inverted or otherwise rotated with respect to the object.

Afocal systems have no focal points, principal points, or nodal points. In such systems an object ray parallel to the optical axis is conjugate to an image ray parallel to the optical axis. A system is focal if an object ray parallel to the axis is conjugate to an image ray that intersects the optical axis. The intersection of the image ray with the optical axis is the focal point F' in image space. Focal systems also have an axial object point F such that any ray through F is conjugate to an image ray parallel to the optical axis. F is the object space focal point of the system.

The transformation between object space and image space is completely defined by the cardinal points of the system, and these points can be used to map any point on the object to its conjugate image point.