Pin weaving

The equipment needed is minimal, consisting of pins, a pinnable board, and a bodkin needle.[4] It can also be done on some types of knitting frame.[5] There are also commercial looms made for pin weaving. Smooth, rounded pin tops are desirable; they don't snag the yarn or fingers.[1] Pins are usually spaced ¼ to ⅛ of an inch apart (3-7 millimeters apart).[2] The pins may be numbered (with numbers written beside the pins), and the lower-left corner may be marked, for ease of reference when working patterns.[6] Ideally, the background should contrast with the threads.[7]

• 
  Weaving by wrapping the warp and weft threads between pins stuck into a pinnable surface (in this case, cork; foamcore is also used.[8]).
• 
  Pin weaving on a mass-produced pin loom

For plain tabby weaves, only every other thread in one direction (a quarter of the yarns) is inserted over-and-under with a needle. The others are wrapped in layers; first the odd warps, then the odd counterwarps (at 90 degrees to the warp threads), then the even warp threads. The counterwarps thus pass alternately over and under the warps, but they do it in parallel, passing over and under in unison. A weft thread is woven between each pair of counterwarps, passing under where the flanking counterwarps pass over, and vice-versa.

This timesaving method cannot be used for more complex weaves, such as twills. For these, the odd warps are warped, then the even warps are warped (giving the edge loops), and then the weft is woven with the needle. There is no counterwarp.

• 
  1. Odd warps are warped
  2. Odd counterwarps are warped, at right angles to the warps
  3. Even warps are warped
  4. Weft is woven, filling in the spaces between the counterwarps
• 
  Partway through stage four of a tabby weave, on a commercial loom.
• 
  Weaving a twill; no counter-warp.
• 
  Weaving a patterned twill. Note that an even pin spacing gives an uneven yarn spacing; pins clustered in threes produce an even yarn spacing.
• 
  Cotton-and-silk weft-faced tapestry on pins in cork sheet; the complexity of the weft means it has to be woven manually

Pin-woven textiles are small, and are often stitched together into larger textiles; the finished product has visible seams. Joining methods including whip stitch, cross stitch, running stitch, back stitch; overcast stitch is fast but tends to pucker. In crochet, crocheted slip stitch and single crochet are used, as are knitted 3-needle bind-offs.[9]

• 
  Two joining methods, termed "lacy stitch" and "cross stitch"
• 
  Decorative joining methods: overcast stitch, featherstitches, and an overcast stitch with an extra turn
• 
  An overcast-stitch join tends to pucker
• 
  A manual lockstich to create a smoother seam
• 
  Squares with crochet borders
• 
  Sweater pattern with waist and cuffs of ribbed knitting, and crochet-edged collar.

• 
  Woven patterns on the cover of a 1937 pattern-book
• 
  Coat from a 1938 patternbook. Seams between squares can be seen. Note rectangular garment construction, with underarm gussets made from squares folded on the diagonal, and tarikubi collar.
• 
  Textured-weave baby blanket from the same pattern book. Seams between squares are used decoratively.
• 
  A shoulder-buttoned sweater, made with full-sized and quartered-sized squares (1936 pattern). Knit waist and cuffs.
• 
  Pattern for the sweater in the previous image, showing rectangular construction.
• 
  Some commercial looms have bars used to make fractional-sized squares.
• 
  Eased horizontal seams in a pattern for an evening cape, 1937.
• 
  Cutting curved pattern-pieces

Many sewing patterns designed for pinweaving use rectangular construction, with all seams lying on selvage edges. This eliminates waste. Others use non-rectangular construction, cutting curve-edged pattern pieces out of a piece of cloth formed by sewing together the squares. Garments can be cut on the bias or on the grain with similar amounts of waste.

Seams joing the squares may be eased; that is, there are more squares on one side of the join than on the other. The extra length is distributed evenly along the seam, creating fullness without discrete pleats.

Darning loom with a shedding mechanism.

Darning looms are similar to pin weaving, but instead of being wrapped around pins, three of the selvages are stitched into the cloth being repaired. The fourth is wrapped around a revolving-hood mechanism which, when rotated, forms a shed and countershed, making plain tabby weaves much faster. When finished, the hooks are removed, and the fourth selvage is usually stitched to the cloth.

Wikimedia Commons has media related to Pin weaving.