Power plant efficiency

The efficiency of a plant is the percentage of the total energy content of a power plant's fuel that is converted into electricity. The remaining energy is usually lost to the environment as heat unless it is used for district heating.

See also: Waste heat, Combined heat and power, and cogeneration

Rating efficiency is complicated by the fact that there are two different ways to measure the fuel energy input:[1]

  • LCV = Lower Calorific Value (same as NCV = Net Calorific Value) neglects thermal energy gained from exhaust H2O condensation
  • HCV = Higher Calorific Value (same as GCV, Gross Calorific Value) includes exhaust H2O condensed to liquid water

Depending on which convention is used, a differences of 10% in the apparent efficiency of a gas fired plant can arise, so it is very important to know which convention, HCV or LCV (NCV or GCV) is being used.

Heat rate

Heat rate is a term commonly used in power stations to indicate the power plant efficiency. The heat rate is the inverse of the efficiency: a lower heat rate is better.

[2]

The term efficiency is a dimensionless measure (sometimes quoted in percent), and strictly heat rate is dimensionless as well, but often written as energy per energy in relevant units. In SI-units it is joule per joule, but often also expressed as joule/kilowatt hour or British thermal units/kWh.[3] This is because kilowatt hour is often used when referring to electrical energy and joule or Btu is commonly used when referring to thermal energy.

Heat rate in the context of power plants can be thought of as the input needed to produce one unit of output. It generally indicates the amount of fuel required to generate one unit of electricity. Performance parameters tracked for any thermal power plant like efficiency, fuel costs, plant load factor, emissions level, etc. are a function of the station heat rate and can be linked directly.[4]

Given that heat rate and efficiency are inversely related to each other, it is easy to convert from one to the other.

  • A 100% efficiency implies equal input and output: for 1 kWh of output, the input is 1 kWh. This thermal energy input of 1 kWh = 3.6 MJ = 3,412 Btu
  • Therefore, the heat rate of a 100% efficient plant is simply 1, or 1 kWh/kWh, or 3.6 MJ/kWh, or 3,412 Btu/kWh
  • To express the efficiency of a generator or power plant as a percentage, invert the value if dimensionless notation or same unit are used. For example:
    • A heat rate value of 5 gives an efficiency factor of 20%.
    • A heat rate value of 2 kWh/kWh gives an efficiency factor of 50%.
    • A heat rate value of 4 MJ/MJ gives an efficiency factor of 25%.
    • For other units, make sure to use a corresponding conversion factor for the units. For example if using Btu/kWh, use a conversion factor of 3,412 Btu per kWh to calculate the efficiency factor. For example, if the heat rate is 10,500 Btu/kWh, the efficiency is 32.5% (since 3,412 Btu / 10,500 Btu = 32.5%).
  • The higher the heat rate (i.e. the more energy input that is required to produce one unit of electric output), the lower the efficiency of the power plant.
  • The U.S. Energy Information Administration gives a general explanation for how to translate a heat rate value into a power plant's efficiency value.[4]

Most power plants have a target or design heat rate. If the actual heat rate does not match the target, the difference between the actual and target heat rate is the heat rate deviation.

See also

References
  1. "Fuels - Higher and Lower Calorific Values". www.engineeringtoolbox.com. Retrieved 2022-02-14.
  2. "Heat Rate Formula". VEDANTU. Retrieved 2022-02-14.
  3. "U.S. Energy Information Administration (EIA)". U.S. Energy Information Administration. Retrieved 2 September 2017.
  4. "What is the efficiency of different types of power plants?". U.S. Energy Information Administration. Retrieved 15 December 2015.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.