pmset

The pmset utility recognizes the following arguments. Arguments can be passed in serial form in any order. Any bad syntax or unrecognized argument will cause the entire command to fail, resulting in an error message and brief help screen. Power management settings can only be changed by a privileged user.

• displaysleep – display sleep timer in minutes, 0 to disable display sleep
• disksleep – disk spin-down timer in minutes, 0 to disable disk sleep
• sleep – system sleep timer in minutes, 0 to disable sleep
• womp - wake on "magic" Ethernet packet, 1 to enable or 0 to disable. Note this setting only appears when running "pmset -g" if the device is plugged into a power source. Otherwise, the womp setting will NOT appear when running "pmset -g".
• hibernatemode change hibernation mode, 0 for RAM powered while sleeping; 1 for RAM contents written to disk and system totally unpowered; 3 for RAM both powered and written to disk; 5 is the same as mode 1, but for use with secure virtual memory; 7 is the same as mode 3, but for use with secure virtual memory; 25 for hibernation in Mac OS X 10.7, with RAM contents written to disk and system totally unpowered
• hibernatefile change hibernation image file location; image may only be located on the root volume
• ring wake on modem ring, 1 to enable or 0 to disable
• autorestart automatic restart after loss of power, 1 to enable or 0 to disable
• dps dynamically change processor speed based on load, 1 to enable or 0 to disable
• reduce permanently reduce processor speed, 1 to enable or 0 to disable
• powerbutton put the machine to sleep when the power button pressed instead of shutting it down, 1 to enable or 0 to disable
• powernap lets machine stay up to date even while they're sleeping, 1 to enable or 0 to disable
• lidwake (laptop only) wake the machine when the laptop lid is opened, 1 to enable or 0 to disable
• acwake (laptop only) wake the machine when the power source is changed, such as when AC power is removed and the machine switches to battery power, 1 to enable or 0 to disable
• lessbright (laptop only) slightly turn down display brightness when switching to a specified power source, 1 to enable or 0 to disable
• halfdim display sleep will use an intermediate half-brightness state between full brightness and fully off, 1 to enable or 0 to disable
• sms (supported laptops only) use Sudden Motion Sensor to park disk heads on sudden changes in G force, 1 to enable or 0 to disable
• haltlevel (UPS only) UPS charge in percentage, shut down the machine when UPS reaches a specified charge level
• haltafter (UPS only) UPS charge in minutes, shut down machine after drawing on UPS for specified number of minutes
• haltremain (UPS only) UPS charge in minutes, shut down machine when specified time remains on UPS
• ttyskeepawake prevent idle system sleep when any tty (such as a remote login session) is active; a tty is inactive only when its idle time exceeds the system sleep timer, 1 to enable or 0 to disable
• autopoweroff (AC power) Where supported, enabled per default as an implementation of Lot 6 to the European Energy-related Products Directive. After sleeping for autopoweroffdelay minutes, the system will write a hibernation image and go into a lower power chipset sleep. Wakeups from this state will take longer than wakeups from regular sleep. The system will not auto power off if any external devices are connected, if the system is on battery power, or if the system is bound to a network and wake for network access is enabled.
• autopoweroffdelay (AC power) delay before entering autopoweroff mode. (Value = integer, in seconds)
• standbydelaylow Delay before writing the hibernation image to disk and powering off memory for Standby. standbydelaylow is used when the remaining battery capacity is low. (Value = integer, in seconds)
• standbydelayhigh Delay before writing the hibernation image to disk and powering off memory for Standby. standbydelayhigh is used when the remaining battery capacity is high. (Value = integer, in seconds)
• networkoversleep This setting affects how macOS networking presents shared network services during system sleep. This setting is not used by all platforms; changing its value is unsupported.
• destroyfvkeyonstandby Destroy File Vault Key when going to standby mode. By default File vault keys are retained even when system goes to standby. If the keys are destroyed, user will be prompted to enter the password while coming out of standby mode. (value: 1 - Destroy, 0 - Retain). Since it is essential that the system fully powered down, you also need to set `hibernatemode` to 25 (suspend to disk).

Settings may be adjusted independently for circumstances where the machine is attached to a charger, when running off a battery (in the case of a laptop), or when running off a UPS (if available). Settings can also be adjusted for all four scenarios simultaneously; this is the default option, for when no usage flag is specified. Power management options can be specified for different profiles by appending -c (charger), -b (battery), -u (UPS) or -a (all) flags. The following example will set the machine to sleep after 10 minutes and sleep the display after five minutes, but only when powered by the battery.

pmset -b sleep 10 displaysleep 5

The following command will assign slightly different power management settings for circumstances where the machine is powered by the charger. Here, the machine is set to sleep after 30 minutes and the display is set to never sleep, but only when set by the charger. Issuing both commands will not interfere with each other.

pmset -c sleep 30 displaysleep 0

Arguments can be entered in serial form to set or modify several power management parameters with one command. The following command will set the machine to never sleep (sleep 0), enable the Sudden Motion Sensor (sms 1), set the display to sleep after 20 minutes (displaysleep 20), disable processor speed reduction (reduce 0), enable intermediate display dimness (halfdim 1), enable the machine to wake when the lid is opened (lidwake 1), prevent the system from sleeping when a tty session (such as SSH) is active (ttyskeepawake 1), disable waking the machine when the AC adapter is inserted (acwake 0), disable an automatic restart after power is removed and restored (autorestart 0), enable dynamic change of processor speed based on system load (dps 1), enable wake on modem ring (ring 1), enable wake on receipt of "magic" Ethernet packet (womp 1), and disable hard disk sleep (disksleep 0):

pmset sleep 0 sms 1 displaysleep 20 reduce 0 halfdim 1 lidwake 1 ttyskeepawake 1 acwake 0 autorestart 0 dps 1 ring 1 womp 1 disksleep 0

Because the above example did not include a usage flag, the settings specified will apply to all usage scenarios. Subsequent commands that do specify a usage flag will only affect settings for that usage scenario. For instance, pmset -b sleep 10 will cause the machine to sleep after 10 minutes, but only when the battery is attached. All other settings will apply when the battery is attached, and all settings in the above example will apply when a charger or UPS is attached.

At least as of Darwin 9.4 and OS X 10.5.4 "Leopard", all changes made through pmset are saved in a persistent preferences file at /Library/Preferences/SystemConfiguration/com.apple.PowerManagement.plist. This file can be modified manually using the defaults command, but those changes will not be taken up immediately by the power management system. Manual edits of com.apple.PowerManagement.plist also stand the risk of being overwritten. The command pmset touch will reread existing settings from disk and apply them to the system.

With autopoweroff enabled the machine will go into hibernate mode even if hibernatemode is 0. The value of autopoweroffdelay may be in seconds despite the man page (for Mavericks, Nov 9, 2012) documenting it as minutes.

The pmset command is able to schedule system sleep, shutdown, wakeup or power on events. The schedule argument is for setting up one-time power events, and repeat is for setting up daily or weekly events. Scheduling of events can only be done by a privileged user.

The schedule argument recognizes the following additional arguments:

• type; one of sleep, wake, poweron, shutdown or wakeorpoweron
• date and time (schedule only); in the format "MM/dd/yy HH:mm:ss"; must be in 24-hour format, must be in quotes
• time (repeat only); in the format HH:mm:ss; must be in 24 format, but does not have to be in quotes
• weekdays; a subset of MTWRFSU such as M or MTWRF are valid, as are strings weekdays, weekends, and everyday
• owner; a string describing the person or program who is scheduling the power event (optional)

The utility can be very unforgiving of improper syntax. Any errors in syntax will cause the command to fail and will display a brief help message. The syntax for a scheduled event is as follows:

pmset schedule [sleep, wake, poweron, shutdown, wakeorpoweron] "MM/dd/yy HH:mm:ss"

Only one type of event (sleep, wake, et cetera) can be specified, and the date chosen must be in the future. The utility expects to be able to store this information in the PMU, and so may not work reliably on non-Apple hardware. The date and time string must be enclosed in quotation marks.

The syntax for a repeating event is as follows:

pmset repeat [sleep, wake, poweron, shutdown, wakeorpoweron] [MTWRFSU, weekdays, weekends, everyday] HH:mm:ss

Scheduled wake, sleep and power events are stored in a persistent preferences file in /Library/Preferences/SystemConfiguration/com.apple.AutoWake.plist. This file can be manually edited using the defaults command, but any changes so made stand a serious risk of being overwritten. Also, such edits will not be immediately taken up by the system.

The list flag, -g, displays information about the current power configuration. The flag alone, with no additional arguments, will display current power management settings. Additional arguments will display more specific information. The get functions of pmset do not require privileged access. The utility recognizes the following arguments (an up-to-date list can be retrieved with the undocumented pmset -g getters command, though it does not show all *log variants):

• live like -g with no option, displays the settings currently in use
• custom will display custom settings for all power sources, although these settings may not currently be in use
• cap capabilities, display which power management features the machine supports
• sched schedule, display scheduled startup, wake, shutdown and sleep events
• ups will display UPS emergency thresholds
• ac or adapter will display details about an attached AC power adapter. Only supported for MacBook and MacBook Pro.
• ps or batt power source, display status of connected batteries and UPSs
• accps will display details of power sources for accessories
• pslog display an ongoing log of power source state
• rawlog display an ongoing log of power source state as read directly from battery
• rawbatt display battery state
• therm shows thermal conditions (not on all platforms)
• thermlog show an ongoing log of thermal notifications (not on all platforms)
• assertions displays the summary of current power assertions (10.6 and later)
• assertionslog displays an ongoing log of power assertions (10.6 and later)
• sysload displays the system load advisory (10.6 and later)
• useractivity show current user activity status
• useractivitylog show an ongoing log of user activity events
• log show a history log of events
• history show a timeline of events for debugging
• historydetailed show driver-level timings for the UUID of a history event
• hidnull show status of
• userclients display a list of processes accepting/sending events
• uuid display the currently active sleep/wake UUID
• rtc display raw RTC data
• getters display a list of valid options for -g
• powerstate display the current power state of all device drivers
• stats display the sleep/wake statistics
• systemstate display the current power state and the system's power capabilities
• everything display everything

Only one get argument can be passed to pmset -g. For instance, to display scheduled events, type pmset -g sched. The utility will not return an error if more than one get argument is provided, but all other than the first will be ignored.

The sleep and displaysleep can show an imposed value of 0 (disabled) together with a list of process IDs that impose this value. These are processes such as backup programs which need the machine to stay awake, for example until the backup is finished.