Portal axle

Portal axles (or portal gear lifts) are an off-road vehicle suspension and drive technology where the axle tube or the half-shaft is off-set from – usually above – the center of the wheel hub and where driving power is transferred to each wheel via a simple gearbox, built onto each hub.[1] This gives two advantages: ground clearance is increased, particularly beneath the low-slung differential housing of the main axles — and secondly, any hub reduction gearing allows the axle halfshafts to drive the same power but at reduced torque (by using higher shaft speed). This reduces load on the axle crownwheel and differential.

Comparison between normal and portal axles
Pinzgauer portal axle

The portal gear configuration is also sometimes called a drop gear or drop gearset configuration[2][3] (which, despite its similarity to the term dropped axle, produces the opposite effect).

Description

Simple portal gearbox from a WW2 Volkswagen Type 82 Kübelwagen

Compared to normal layout, portal axles enable the vehicle to gain a higher ground clearance, as both the axle tube and differential casing are tucked up higher under the vehicle.

Due to the gear reduction at the wheel which lessens the torque on all the other drivetrain components, the size of the differential casing can be reduced to gain even more ground clearance. Additionally, all drivetrain elements, in particular the transfer gearbox and driveshafts, can be built lighter. This can be of use in lowering the center of gravity for a given ground clearance. Where a vehicle also requires a reduced top speed, in at least one gear, the gear ratio can be chosen to reduce this. The military Kübelwagen of WWII used a ratio of 1.4:1 to provide a 2.5 mph walking speed in first gear,[4] as well as a useful lift of 50 mm.

As they require a heavier and more complex hub assembly, however, these systems can result in an increased unsprung weight and require robust axle-control elements to give predictable handling. In addition, at higher speeds the hub assembly can overheat.[5]

1930 Farmall tractor with rear portal axle
1961 Porsche F 108 tractor with rear portal axle

They are also used in railways and low floor buses[6][7] although, in the case of buses, the device is engineered in the opposite way to those fitted to off-road vehicles - the axle is below the center of the wheel. Thus, the inverted portal axle allows the floor of the bus to be lowered, easing access to the bus and increasing the available cabin height.

A Land Rover Defender fitted with bolt-on portal axles

Bolt-on portals (or drop boxes) are a housing with a set of gears which bolts onto the final flange of the axle tube. This approach allows existing vehicles to be converted to use portal gear lifts without modifying the axles (Volvo C303 or Unimog 404).

Examples

Vehicles fitted with portal axles include:

In-line gearboxes

A related development is the use of an epicyclic hub gearbox. This is mounted in-line with the halfshaft, so that there is no change in ride height. They are often used for large and heavy vehicles, where the wheel diameter already gives adequate ground clearance. The reduction gearbox allows the halfshafts to turn faster than the wheels, thus requiring less torque for the same power. This permits a smaller and lighter halfshaft and internal drivetrain.

Hub gearboxes were an iconic feature of the Alvis FV600 chassis vehicles, such as the Stalwart and Saracen. The FV600 used a version of the DAF H-drive, with a single differential between sides and all wheels on each side linked by an internal driveshaft and bevel gearboxes to the halfshafts. This has no differential axle between wheel stations on each side and so 'wind-up' was a regular problem for these vehicles when driven on roads. If individual wheels were out of phase with their neighbours, possibly caused by cornering or slightly varying tyre diameter, this could place a considerable force on the gearbox, leading to breakages. For this reason, it was regular practice when driving on tarmac to bump the vehicle over a kerb or other object at times, to allow this wind-up to be released. On slippery surfaces like sand or mud there is enough slippage between the tyres and ground to dissipate the tension.

They are now found on many large quarrying dump trucks and heavy plant.

Manufacturing

Today, portal gear lifts are manufactured for use in utility task vehicles (UTV).

See also

References

  1. "New Spicer portal axles for compact utility tractors - introduced by Off-Highway Systems Group of Dana Corp". Diesel Progress North American Edition.
  2. U.S. Patent 20,130,240,282
  3. U.S. Patent 6,095,005
  4. Ludvigsen, Karl (2014). Professor Porsche's Wars. Pen & Sword Military. pp. 134–135. ISBN 978-1-52672-679-7.
  5. Exaxt 4WD Archived 2008-12-19 at the Wayback Machine
  6. Railway Technology - Portal axle with SAB V60 rubber-sprung wheels and sound absorbers
  7. ArvinMeritor Reveals New Second Generation Inverted Portal Axle Archived 2007-11-01 at the Wayback Machine
  8. 4WD Glossary & FAQ Archived 2007-12-11 at the Wayback Machine
  9. "Archived copy" (PDF). www.internationaldelivers.com. Archived from the original (PDF) on 9 July 2006. Retrieved 22 May 2022.{{cite web}}: CS1 maint: archived copy as title (link)
  10. An Expedition Truck on Portals
  11. "Mercedes releases 6x6 G63 AMG specs and pics [w/Video]". Archived from the original on 2013-04-10. Retrieved 2013-03-15.
  12. "The Unimog Principle". Archived from the original on 2008-07-18. Retrieved 2007-12-04.
  13. Michael Trzesniowski: Rennwagentechnik: Grundlagen, Konstruktion, Komponenten, Systeme, Vieweg+Teubner Verlag, Wiesbaden, 2012, page 782–783 ISBN 978-3-8348-2209-3
  14. "portal-compare.htm". Archived from the original on 2007-10-08. Retrieved 2007-12-04.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.