Recoil operation

Key for recoil operation diagrams. Gun fires to the right.

Block diagram of long recoil operation cycle.

Long recoil operation is found primarily in shotguns, particularly ones based on John Browning's Auto-5 action. In 1885 a locked breech, long recoil action was patented by the Britons Schlund and Arthur.[9] In a long recoil action, the barrel and bolt remain locked together during recoil, compressing the recoil springs. Following this rearward movement, the bolt locks to the rear and the barrel is forced forward by its spring. The bolt is held in position until the barrel returns completely forward during which time the spent cartridge has been extracted and ejected, and a new shell has been positioned from the magazine. The bolt is released and forced closed by its recoil spring, chambering a fresh round.

The long recoil system was invented in the late 19th century and dominated the automatic shotgun market for more than half that century before it was supplanted by new gas-operated designs. While Browning halted production of the Auto-5 design in 1999, Franchi still makes a long-recoil–operated shotgun line, the AL-48, which shares both the original Browning action design, and the "humpbacked" appearance of the original Auto-5. Other weapons based on the Browning system were the Remington Model 8 semi-automatic rifle (1906), the Remington Model 11 & "The Sportsman" model (a model 11 with only a two-shell magazine) shotguns, the Frommer Stop line of pistols (1907), and the Chauchat automatic rifle (1915).

Cycle diagram explanation

1. Ready to fire position. Bolt is locked to barrel, both are fully forward.
2. Recoil of firing forces bolt and barrel fully to the rear, compressing the return springs for both.
3. Bolt is held to rear, while barrel unlocks and returns to battery under spring force. Fired round is ejected.
4. Bolt returns under spring force, loads new round. Barrel locks in place as it returns to battery.

The barrel from a Para Ordnance P12.45, an M1911-derived design which uses short recoil operation. Under recoil, the barrel moves back in the frame, rotating the link (shown in the unlocked position), which causes the rear of the barrel to tip down and disengage from the slide.

The short recoil action dominates the world of centerfire semi-automatic pistols, being found in nearly all weapons chambered for high-pressure pistol cartridges of 9×19mm Parabellum and larger, while low-pressure pistol cartridges of .380 ACP and smaller generally use the blowback method of operation. Short recoil operation differs from long recoil operation in that the barrel and bolt recoil together only a short distance before they unlock and separate. The barrel stops quickly, and the bolt continues rearward, compressing the recoil spring and performing the automated extraction and feeding process. During the last portion of its forward travel, the bolt locks into the barrel and pushes the barrel back into battery.

The method of locking and unlocking the barrel differentiates the wide array of short recoil designs. Most common are the John Browning tilting barrel designs based on either the swinging link and locking lugs as used in the M1911 pistol or the linkless cam design used in the Hi Power and CZ 75. Other designs are the locking block design found in the Walther P38 and Beretta 92, rollers in the MG42, or a rotating barrel used in the Beretta 8000 and others. An unusual variant is the toggle bolt design of the Borchardt C-93 and its descendant, the Luger pistol.

While the short recoil design is most common in pistols, the very first short-recoil–operated firearm was also the first machine gun, the Maxim gun. It used a toggle bolt similar to the one Borchardt later adapted to pistols. Vladimirov also used the short recoil principle in the Soviet KPV-14.5 heavy machine gun which has been in service with the Russian military and Middle Eastern armed forces since 1949. Melvin Johnson also used the short recoil principle in his M1941 rifle and M1941 Johnson machine gun.

Cycle diagram explanation

Block diagram of short recoil operation cycle. See diagram key above.

1. Ready to fire position. Bolt is locked to barrel, both are fully forward.
2. Upon firing, bolt and barrel recoil backwards a short distance while locked together. Near the end of the barrel travel, the bolt and barrel unlock.
3. The barrel stops, but the unlocked bolt continues to move to the rear, ejecting the empty shell and compressing the recoil spring.
4. The bolt returns forward under spring force, loading a new round into the barrel.
5. Bolt locks into barrel, and forces barrel to return to battery.

An alternative design concept for recoil-operated firearms is the inertia operated system, the first practical use of it being the Sjögren shotgun, developed by Carl Axel Theodor Sjögren in the early 1900s, a Swedish engineer who was awarded a number of patents for his inertia operated design between 1900 and 1908 and sold about 5,000 automatic shotguns using the system in 1908–1909.[10][11] In a reversal of the other designs, some inertia systems use nearly the entire firearm as the recoiling component, with only the bolt remaining stationary during firing. Because of this, the inertia system is only applied to heavily recoiling firearms, particularly shotguns. A similar system using inertia operation was then developed by Paolo Benelli in the early 1980s and patented in 1986.[12] With the exception of Sjögren's shotguns and rifles in the early 1900s, all inertia-operated firearms made until 2012 were either made by Benelli or used a design licensed from Benelli, such as the Franchi Affinity. Then the Browning Arms Company introduced the inertia-operated A5 (trademarked as Kinematic Drive) as successor to the long-recoil operated Auto-5. Both the Benelli and Browning systems are based on a rotating locking bolt, similar to that used in many gas-operated firearms.

Before firing, the bolt body is separated from the locked bolt head by a stiff spring. As the shotgun recoils after firing, inertia of the bolt body is large enough for it to remain stationary while the recoiling gun and locked bolt head move rearward. This movement compresses the spring between the bolt head and bolt body, storing the energy required to cycle the action. Since the spring can only be compressed a certain amount, this limits the amount of force the spring can absorb, and provides an inherent level of self-regulation to the action, allowing a wide range of shotshells to be used, from standard to magnum loads, as long as they provide the minimum recoil level to compress the spring. Note that the shotgun must be free to recoil for this to work—the compressibility of the shooter's body is sufficient to allow this movement, but firing the shotgun from a secure position in a rest or with the stock against the ground will not allow it to recoil sufficiently to operate the mechanism. Likewise, care must be exercised when modifying weapons of this type (e.g. addition of extended magazines or ammunition storage on the stock), as any sizable increase in weapon mass can reduce the work done from recoil below that required to cycle the action.

Block diagram of inertia operation cycle, see diagram key above

As the recoil spring returns to its uncompressed state, it pushes the bolt body backward with sufficient force to cycle the action. The bolt body unlocks and retracts the bolt head, extracts and ejects the cartridge, cocks the hammer, and compresses the return spring. Once the bolt reaches the end of its travel, the return spring provides the force to chamber the next round from the magazine, and lock the bolt closed.

Cycle diagram explanation

1. Ready to fire position. Bolt is locked to barrel, both are fully forward.
2. Upon firing, the firearm recoils backwards into the shooter's body. The inertial mass remains stationary, compressing a spring. The bolt remains locked to the barrel, which in turn is rigidly attached to the frame.
3. The compressed spring forces the inertial mass rearwards until it transfers its momentum to the bolt.
4. The bolt unlocks and moves to the rear, ejecting the fired round and compressing the return spring.
5. The bolt returns to battery under spring force, loading a new round and locking into place.
6. The shooter recovers from the shot, moving the firearm forward into position for the next shot.

Some short-recoil–operated firearms, such as the German MG 42 and MG 3, use a mechanism at the muzzle to extract some energy from the escaping powder gases to push the barrel backwards, in addition to the recoil energy. This boost provides higher rates of fire and/or more reliable operation. This type of mechanism is also found in some suppressors used on short recoil firearms, under the name gas assist or Nielsen device, where it is used to compensate for the extra mass the suppressor adds to the recoiling parts both by providing a boost and decoupling some of the suppressor's mass from the firearm's recoiling parts.

Muzzle boosters are also used on some recoil-operated firearms' blank-firing attachments to normalize the recoil force of a blank round (with no projectile) with the greater force of a live round, in order to allow the mechanism to cycle properly.

Several revolvers use recoil to cock the hammer and advance the cylinder. In these designs, the barrel and cylinder are affixed to an upper frame which recoils atop a sub-frame. As the upper receiver recoils, the cylinder is advanced and hammer cocked, functions that are usually done manually. Notable examples are the Webley–Fosbery and Mateba.