Ruger P series

The P85 was developed in 1985, but was not available until 1987.[1] It was only available with a DA/SA trigger, decocker, and a manual safety. The P85 was affordable, initially retailing for just $295, about $100 cheaper than its nearest competitors.

The Ruger P85 is a full-sized DA/SA alloy-framed service pistol originally designed to compete in the 1984 U.S. military pistol trials. Unfortunately the design wasn't finalized until after the trials. The P85 found popularity on the civilian and law enforcement markets but many were recalled after one incident with the firing pin, resulting in a discharge. If the firing pin broke in front of the firing pin block, applying the safety, which dropped the hammer, could transfer enough energy to the broken firing pin to cause a discharge. The P85 was recalled, and a new safety was installed that prevented contact between firing pin and hammer during a decocking operation. This modification was done free of charge. This updated P85 was christened as the P85 MK II in 1989. Other updates included larger safety levers and improved accuracy. The P85 MK II was produced for several more years, until 1992. By then the P89 was in production (having been introduced the previous year), which is essentially just a re-branded P85 MK II. After the P89 was introduced, there was no longer a need to produce the P85 and it was discontinued.[1][3]

Both variants are chambered in 9mm and have a magazine capacity of 15+1 rounds.

Blued Ruger P89

The P89 is an upgraded P85 MKII that introduced a number of new features, including a DAO model. Like the P85, all P89s came with an investment cast aluminum alloy frame. In 1992, Ruger produced a limited-run P89X convertible model, which came with a second barrel and recoil spring assembly that allowed conversion between 9 mm and .30 Luger calibers. Ruger only made 5,750 with both barrels in 1994 only. The P89 was one of the most popular and plentiful P-series models. It was discontinued in late 2009.[8]

It was chambered in 9mm, with magazine capacities of 15+1 rounds .

Ruger KP90DC (decocker)

The P90 is a scaled-up version of the P89 chambered in .45 ACP with an investment cast aluminum alloy frame. It was introduced in 1991 as the company's first attempt at a .45 ACP pistol, and was in direct competition with SIG Sauer's P220, Smith & Wesson's 4500 series, and to a lesser extent Glock's G21 that came out the same year. The P90 is considered to have above-average accuracy for its price. The P90 was produced until 2010.[1]

It has a magazine capacity of 7 rounds.

The Ruger P91 is essentially a Ruger P89 chambered in .40 Smith & Wesson. Like its precursors, it also had an investment cast aluminum alloy frame. It was only produced for two years, from 1992 to 1994. It has a magazine capacity of 11 rounds, with 10 round magazines being developed for the 1994 ban.

KP94DC, decock-only model

The P93 was developed in 1993 but not released until 1994. The P93 was designed as a compact version of the Ruger P89 and, as such, still had the investment cast aluminum alloy frame, though the frame was slimmer than that of the P89 and it omitted some unnecessary parts. It was designed for shooters interested in lighter weight or easier concealability. The P93 lacks the flared nosepiece of the P89 and also features different grips with heavier checkering. Standard capacity was either 15 or 10 rounds. The P93 has a 3.9-inch (99.1 mm) barrel that utilized a dropping link like the P89. A larger number of P93s than other variants were also double action-only without an external safety, due to its intended concealed carry market. The P93 was discontinued in 2004.

Original model KP95, without the Picatinny rail

The Ruger P94 is a mid-sized, slightly larger variant of the P93. The P94 has a 4.3-inch (109.2 mm) long barrel as opposed to a 3.9-inch (99.1 mm) barrel and still has the investment cast aluminum alloy frame. Like the P93, the P94 was introduced in 1994. The P94 features different grips with heavier checkering. The P94 has a full-length “streamlined” slide configuration and is chambered for the 9mm Parabellum (9 mm x 19) cartridge, while the P944D is chambered for the .40 S&W cartridge.[9] The P94 was discontinued in 2004, ten years after its introduction. However the P944D variant was produced until 2009.

It can be chambered in either 9mm or .40 S&W, with magazine capacities of 15+1 or 10+1, respectively.[10] There is also a Law Enforcement Use Only 11+1 magazine for the P944 in .40 S&W.

Late model P95PR with Picatinny rail and a Hogue Handall grip installed

Introduced in 1996, the P95 incorporated a number of changes from earlier P-series pistols, including a shorter 3.9-inch (99.1 mm) barrel like the P93. The big change was switching the frame construction from an investment cast aluminum alloy to a new high-impact polymer frame made of fiberglass-reinforced polyurethane, based on Dow Chemical's "Isoplast".[2] The P95 was also the first pistol in the series to omit the dropping link underneath the barrel. The first P95s came with a glossy black polymer frame with a hooked trigger guard and lacking an accessory rail and grip texture. Later model P95s featured a matte polymer frame with enhanced grip texturing, an accessory rail and a round trigger guard. The P95 was one of the last in the series to be fully discontinued. Most P95 designs were discontinued in 2004 and 2005, but certain types of the P95 were produced until 2009 and 2013.

It is chambered in 9mm with a magazine capacity of 15+1 rounds.

The P97 is essentially a P95 chambered in .45 ACP, similar to the P90. The P97 feeds from a single-stack 8+1 .45 ACP magazine, the same magazine used in the P90. It was only available in decocker only and double-action only versions. It featured an adjustable rear sight and retained the same glass-filled polymer frame of the P95. The front sight is pinned in, and the rear held in by a set screw. Unlike the P95, however, the P97 never got the improved frame with added grip texture and an accessory rail and retained the original smooth frame. The P97 was manufactured from 1999 to 2004.

The P345, released in 2004, is a transition model between the P series and the SR series. The P345 is chambered in .45 ACP and accepts the same 8+1 single stack magazines as the P90 and the P97. The P345 features a radically different design (as it was intended to usher in Ruger's new pistol designs) and incorporates an integrated keyed lock that locks the safety in the safe position, a loaded chamber indicator, and a magazine disconnect that blocks the firing pin when the magazine is removed. It also has many ergonomic improvements, such as a new polymer frame design (narrower than the double column derived P95 and P97) and low-profile safety levers. It does not feature an ambidextrous slide release or magazine release. Both controls are designed for a right-handed shooter. The model P345PR adds a Picatinny rail to the frame, for mounting lights and other accessories. It was designed to be legal for sale in states that require elaborate safety measures. The P345 was discontinued in 2013 and replaced by the new SR45.[8]