Booster engine

Invented in 1918 by Howard L. Ingersoll, assistant to the President of the New York Central Railroad,[1] the locomotive booster for steam locomotives is a small two-cylinder steam engine back-gear-connected to the trailing truck axle on the locomotive or one of the trucks on the tender. A rocking idler gear permits it to be put into operation by the driver (engineer). A geared booster engine drives one axle only and can be non-reversible, with one idler gear, or reversible, with two idler gears. There were variations built by the Franklin company which utilized side rods to transmit tractive force to all axles of the booster truck. These rod boosters were predominately used on the leading truck of the tender, though there is an example of a Lehigh Valley 4-8-4 using it as a trailing tender truck.[2]

Booster engine with the cover removed to show the mechanism. The driven axle is on the right; the booster normally hung behind it.
Diagram showing how a booster is installed and connected.

A booster engine is used to start a heavy train or maintain low speed under demanding conditions. Rated at about 300–500 horsepower (220–370 kW) at speeds of from 10 to 35 mph (16 to 56 km/h), it can be cut in while moving at speeds under 12–22 miles per hour (19–35 km/h) and is semi-automatically cut out via the engineer notching back the reverse gear or manually through knocking down the control latch up to a speed of between 21 and 35 mph (34 and 56 km/h), depending on the model and gearing of the booster. A tractive effort rating of 10,000–12,000 pounds-force (44–53 kN) was common, although ratings of up to around 15,000 lbf (67 kN) were possible.[3][4]

Tender boosters are equipped with side-rods connecting axles on the lead truck. Such small side-rods restrict speed and are therefore confined mostly to switching locomotives, often used in transfer services between yards. Tender boosters were far less common than engine boosters; the inherent weight of the tenders would decrease as coal and water were consumed during operation, effectively lowering the adhesion of the booster-powered truck.

Reasons for use

The booster was intended to make up for fundamental flaws in the design of the standard steam locomotive. To start off, most steam locomotives do not provide power to all wheels. The amount of force that can be applied to the rail depends on the weight on the driven wheels and the factor of adhesion of the wheels against the track. Unpowered wheels are generally needed to provide stability at speed, but at low speed they are not required, so they effectively 'waste' weight which could be used for traction. Therefore, the application of a booster engine to the previously unpowered axle meant that overall starting tractive effort was increased with zero penalty to the adhesion levels of the main engine.

Additionally, the "gearing" of a steam locomotive is fixed, because the pistons are linked directly to the wheels via rods and cranks. Therefore, a compromise must be struck between ability to exert high tractive effort at low speed and the ability to run fast without inducing excessive piston speeds (which would cause failure), or the exhaustion of steam. That compromise means that, at low speeds, a steam locomotive is not able to use all the power the boiler is capable of producing; it simply cannot use steam that quickly, so there is a substantial difference between the amount of steam the boiler can produce and the amount that can be used. The booster engine enabled that wasted potential to be put to use.

The increased starting tractive effort provided by the booster meant that, in some instances, railroads were able to reduce the number of, or eliminate entirely the use of additional helper locomotives on heavier trains. This resulted in lower operating and maintenance costs, higher locomotive availability and productivity (ton-miles), and ultimately, greater profitability.

Disadvantages

Boosters were costly to maintain, with their flexible steam and exhaust pipes, idler gear, etc. Improper operation could also result in undesirable drops in boiler pressure and/or damage to the booster. The booster and its associated componentry also added several tons of weight to the locomotive which would be considered "dead weight" at speeds above which the booster could not be used. Additionally, if the booster suffered a failure where the idler gear could not be disengaged, the entire locomotive would be speed restricted to 20 mph or less, until it could be taken out of service to facilitate repairs, decreasing locomotive availability.

Calculating tractive effort and operating speeds

A rough calculation of booster tractive effort could be made with the following formula:[5]

where

  • t is tractive effort in pound-force
  • c is the coefficient representing mean effective pressure, normally set to 0.80
  • d is the piston diameter in inches (bore)
  • s is the piston stroke in inches
  • p is the working pressure in pounds per square inch
  • r is the booster gear ratio
  • w is the diameter of the trailing wheels to which the booster is geared in inches

The typical locomotive booster employed a pair of 10-inch-bore (250 mm) by 12-inch-stroke (300 mm) cylinders. Available gear ratios and associated operating speeds for both the Franklin type C and type E booster models are detailed in the table below.

Locomotive booster gear ratios and associated operating speeds[3][4]
Gear ratio Maximum cut-in speed Maximum operating speed
Franklin Type C-1 & C-2 2.571 12 mph (19 km/h) 21 mph (34 km/h)
Franklin Type E & E-1 2.71 15 mph (24 km/h) 25 mph (40 km/h)
2.25 18.5 mph (29.8 km/h) 30 mph (48 km/h)
2.00 22 mph (35 km/h) 35 mph (56 km/h)

Usage

North America

The booster saw most use in North America. Railway systems elsewhere often considered the expense and complexity unjustified.

Even in the North American region, booster engines were applied to only a fraction of all locomotives built. Some railroads used boosters extensively while others did not. The New York Central was the first railroad to use a booster in 1919 and remained a proponent of the device, applying them to all of its high-drivered 4-6-4 Hudson locomotives to increase their acceleration out of stations with crack passenger trains. The rival Pennsylvania Railroad, however, used few booster-equipped locomotives. Similarly, the Chesapeake & Ohio specified boosters on all of its Superpower locomotives aside from the Allegheny to increase tonnage ratings over some of the hilly terrain found on their main lines, while rival Norfolk & Western experimented with boosters briefly and found their cost unjustified, instead choosing to increase engine tractive effort through the raising of boiler pressure.

Canadian Pacific Railway rostered 3,257 steam locomotives acquired between 1881 and 1949, yet only 55 were equipped with boosters. 17 H1 class 4-6-4s, 2 K1 class 4-8-4s and all 36 Selkirk 2-10-4s.

Australia

In Australia, Victorian Railways equipped all but one of its X class 2-8-2 locomotives (built between 1929 and 1947) with a 'Franklin' two-cylinder booster engine, following a successful trial of the device on a smaller N class 2-8-2 in 1927. From 1929 onwards, South Australian Railways 500 class 4-8-2 heavy passenger locomotives were rebuilt into 4-8-4s with the addition of a booster truck .

New Zealand

NZR's KB class of 1939 were built with a booster truck to enable the locomotives to handle the steeper grades of some South Island lines (particularly the Cass Bank of the Midland Line). Some boosters were later removed because of the gear jamming.

Great Britain

In Great Britain, eight locomotives of four different classes on the London and North Eastern Railway were equipped with booster units by Nigel Gresley. Four were existing locomotives rebuilt with boosters between 1923 and 1932: one of class C1 (in 1923);[6] both of the conversions from class C7 to class C9 (in 1931);[7] and one of class S1 (in 1932).[8] The remaining four were all fitted to new locomotives: the two P1 2-8-2 locomotives, built in 1925;[9] and two class S1 locomotives built in 1932.[8] The boosters were removed between 1935 and 1938,[10][11] apart from those on class S1 which were retained until 1943.[8]

An early type of booster used in Great Britain was the steam tender, which was tried in 1859 by Benjamin Connor of the Caledonian Railway on four 2-4-0 locomotives. Archibald Sturrock of the Great Northern Railway (GNR) patented a similar system on 6 May 1863 (patent no. 1135). It was used on fifty GNR 0-6-0 locomotives: thirty converted from existing locomotives between 1863 and 1866, and twenty built new in 1865 (nos. 400–419). The equipment was removed from all fifty during 1867–68.[12][13]

References

  1. "Locomotive Boosters". Railway Mechanical Engineer. Vol. 98, no. 10. Simmons-Boardman Publishing Corporation. October 1924. p. 590-591 via Internet Archive.
  2. Van Nort, Darryl E (28 March 2023). "Class T-2a 5210". Retrieved 28 March 2023.
  3. "Dynamometer Tests of the Locomotive Booster". Railway Mechanical Engineer. Vol. 96, no. 10. Simmons-Boardman Publishing Corporation. October 1922. p. 562-565 via Internet Archive.
  4. "Dynamometer Tests of Type E Booster". Railway Mechanical Engineer. Vol. 118, no. 9. Simmons-Boardman Publishing Corporation. September 1944. p. 399-401, 408 via Internet Archive.
  5. "Exhibit "G'—Formula for Computing Tractive Effort of Locomotive Booster". Railway Mechanical Engineer. Vol. 103, no. 7. Simmons-Boardman Publishing Corporation. July 1929. p. 443 via Internet Archive.
  6. Boddy, M.G.; Brown, W.A.; Fry, E.V.; Hennigan, W.; Hoole, Ken; Manners, F.; Neve, E.; Platt, E.N.T.; Russell, O.; Yeadon, W.B. (November 1979). Fry, E.V. (ed.). Locomotives of the L.N.E.R., part 3A: Tender Engines - Classes C1 to C11. Kenilworth: RCTS. p. 26. ISBN 0-901115-45-2.
  7. Boddy et al. 1979, p. 122
  8. Boddy, M.G.; Brown, W.A.; Fry, E.V.; Hennigan, W.; Hoole, Ken; Manners, F.; Neve, E.; Platt, E.N.T.; Proud, P.; Yeadon, W.B. (June 1977). Fry, E.V. (ed.). Locomotives of the L.N.E.R., part 9B: Tank Engines - Classes Q1 to Z5. Kenilworth: RCTS. p. 24. ISBN 0-901115-41-X.
  9. Boddy, M.G.; Brown, W.A.; Neve, E.; Yeadon, W.B. (November 1983). Fry, E.V. (ed.). Locomotives of the L.N.E.R., part 6B: Tender Engines - Classes O1 to P2. Kenilworth: RCTS. p. 153. ISBN 0-901115-54-1.
  10. Boddy et al. 1979, pp. 29, 126
  11. Boddy et al. 1983, p. 157
  12. "Great Northern Railway locomotives: Bury, Sturrock & Stirling designs". Steamindex.com. Retrieved 2012-06-16.
  13. Groves, Norman (1986). Great Northern Locomotive History: Volume 1 1847-66. RCTS. pp. 73–74, 83, 105, 109, 111. ISBN 0-901115-61-4.

Further reading

  • Bruce, Alfred W. (1952). The Steam Locomotive in America. Bonanza Books, New York.
  • Railway Master Mechanics' Association (1922). Locomotive Cyclopedia of American Practice, Sixth Edition1922. Simmons-Boardman.
  • Franklin Type C2 Booster Engine
  • Talbot, Fred. A (1923), "The locomotive "booster"", Railways of the World, pp. 84–91 illustrated description of the booster engine
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.