Time-of-flight camera

A time-of-flight camera (ToF camera), also known as time-of-flight sensor (ToF sensor), is a range imaging camera system for measuring distances between the camera and the subject for each point of the image based on time-of-flight, the round trip time of an artificial light signal, as provided by a laser or an LED. Laser-based time-of-flight cameras are part of a broader class of scannerless LIDAR, in which the entire scene is captured with each laser pulse, as opposed to point-by-point with a laser beam such as in scanning LIDAR systems.[1] Time-of-flight camera products for civil applications began to emerge around 2000,[2] as the semiconductor processes allowed the production of components fast enough for such devices. The systems cover ranges of a few centimeters up to several kilometers.

Time of flight of a light pulse reflecting off a target

Types of devices

Several different technologies for time-of-flight cameras have been developed.

RF-modulated light sources with phase detectors

Photonic Mixer Devices (PMD),[3] the Swiss Ranger, and CanestaVision[4] work by modulating the outgoing beam with an RF carrier, then measuring the phase shift of that carrier on the receiver side. This approach has a modular error challenge: measured ranges are modulo the RF carrier wavelength. The Swiss Ranger is a compact, short-range device, with ranges of 5 or 10 meters and a resolution of 176 x 144 pixels. With phase unwrapping algorithms, the maximum uniqueness range can be increased. The PMD can provide ranges up to 60 m. Illumination is pulsed LEDs rather than a laser.[5] CanestaVision developer Canesta was purchased by Microsoft in 2010. The Kinect2 for Xbox One was based on ToF technology from Canesta.

Range gated imagers

These devices have a built-in shutter in the image sensor that opens and closes at the same rate as the light pulses are sent out. Most time-of-flight 3D sensors are based on this principle invented by Medina.[6] Because part of every returning pulse is blocked by the shutter according to its time of arrival, the amount of light received relates to the distance the pulse has traveled. The distance can be calculated using the equation, z = R (S₂ − S₁) / 2(S₁ + S₂) + R / 2 for an ideal camera. R is the camera range, determined by the round trip of the light pulse, S₁ the amount of the light pulse that is received, and S₂ the amount of the light pulse that is blocked.[6][7]

The ZCam by 3DV Systems[1] is a range-gated system. Microsoft purchased 3DV in 2009. Microsoft's second-generation Kinect sensor was developed using knowledge gained from Canesta and 3DV Systems.[8]

Similar principles are used in the ToF camera line developed by the Fraunhofer Institute of Microelectronic Circuits and Systems and TriDiCam. These cameras employ photodetectors with a fast electronic shutter.

The depth resolution of ToF cameras can be improved with ultra-fast gating intensified CCD cameras. These cameras provide gating times down to 200ps and enable ToF setup with sub-millimeter depth resolution.[9]

Range gated imagers can also be used in 2D imaging to suppress anything outside a specified distance range, such as to see through fog. A pulsed laser provides illumination, and an optical gate allows light to reach the imager only during the desired time period.[10]

Direct Time-of-Flight imagers

These devices measure the direct time-of-flight required for a single laser pulse to leave the camera and reflect back onto the focal plane array. Also known as "trigger mode", the 3D images captured using this methodology image complete spatial and temporal data, recording full 3D scenes with single laser pulse. This allows rapid acquisition and rapid real-time processing of scene information. For time-sensitive autonomous operations, this approach has been demonstrated for autonomous space testing[11] and operation such as used on the OSIRIS-REx Bennu asteroid sample and return mission[12] and autonomous helicopter landing.[13][14]

Advanced Scientific Concepts, Inc. provides application specific (e.g. aerial, automotive, space) Direct TOF vision systems[15] known as 3D Flash LIDAR cameras. Their approach utilizes InGaAs Avalanche Photo Diode (APD) or PIN photodetector arrays capable of imaging laser pulse in the 980 nm to 1600 nm wavelengths.

Components

A time-of-flight camera consists of the following components:

Illumination unit: It illuminates the scene. For RF-modulated light sources with phase detector imagers, the light has to be modulated with high speeds up to 100 MHz, only LEDs or laser diodes are feasible. For Direct TOF imagers, a single pulse per frame (e.g. 30 Hz) is used. The illumination normally uses infrared light to make the illumination unobtrusive.
Optics: A lens gathers the reflected light and images the environment onto the image sensor (focal plane array). An optical band-pass filter only passes the light with the same wavelength as the illumination unit. This helps suppress non-pertinent light and reduce noise.
Image sensor: This is the heart of the TOF camera. Each pixel measures the time the light has taken to travel from the illumination unit (laser or LED) to the object and back to the focal plane array. Several different approaches are used for timing; see Types of devices above.
Driver electronics: Both the illumination unit and the image sensor have to be controlled by high speed signals and synchronized. These signals have to be very accurate to obtain a high resolution. For example, if the signals between the illumination unit and the sensor shift by only 10 picoseconds, the distance changes by 1.5 mm. For comparison: current CPUs reach frequencies of up to 3 GHz, corresponding to clock cycles of about 300 ps - the corresponding 'resolution' is only 45 mm.
Computation/Interface: The distance is calculated directly in the camera. To obtain good performance, some calibration data is also used. The camera then provides a distance image over some interface, for example USB or Ethernet.

Principle

Principle of operation of a time-of-flight camera:

In the pulsed method (1), the distance, d = c t2 q2q1 + q2 , where c is the speed of light, t is the length of the pulse, q1 is the accumulated charge in the pixel when light is emitted and q2 is the accumulated charge when it is not.

In the continuous-wave method (2), d = c t2

π

arctan q3 - q4q1 - q2 .[16]

Diagrams illustrating the principle of a time-of-flight camera with analog timing

The simplest version of a time-of-flight camera uses light pulses or a single light pulse. The illumination is switched on for a very short time, the resulting light pulse illuminates the scene and is reflected by the objects in the field of view. The camera lens gathers the reflected light and images it onto the sensor or focal plane array. Depending upon the distance, the incoming light experiences a delay. As light has a speed of approximately c = 300,000,000 meters per second, this delay is very short: an object 2.5 m away will delay the light by:[17]

t_{D}=2\cdot {\frac {D}{c}}=2\cdot {\frac {2.5\;\mathrm {m} }{300\;000\;000\;{\frac {\mathrm {m} }{\mathrm {s} }}}}=0.000\;000\;016\;66\;\mathrm {s} =16.66\;\mathrm {ns}

For amplitude modulated arrays, the pulse width of the illumination determines the maximum range the camera can handle. With a pulse width of e.g. 50 ns, the range is limited to

D_{\mathrm {max} }={\frac {1}{2}}\cdot c\cdot t_{0}={\frac {1}{2}}\cdot 300\;000\;000\;{\frac {\mathrm {m} }{\mathrm {s} }}\cdot 0.000\;000\;05\;\mathrm {s} =\!\ 7.5\;\mathrm {m}

These short times show that the illumination unit is a critical part of the system. Only with special LEDs or lasers is it possible to generate such short pulses.

The single pixel consists of a photo sensitive element (e.g. a photo diode). It converts the incoming light into a current. In analog timing imagers, connected to the photo diode are fast switches, which direct the current to one of two (or several) memory elements (e.g. a capacitor) that act as summation elements. In digital timing imagers, a time counter, that can be running at several gigahertz, is connected to each photodetector pixel and stops counting when light is sensed.

In the diagram of an amplitude modulated array analog timer, the pixel uses two switches (G1 and G2) and two memory elements (S1 and S2). The switches are controlled by a pulse with the same length as the light pulse, where the control signal of switch G2 is delayed by exactly the pulse width. Depending on the delay, only part of the light pulse is sampled through G1 in S1, the other part is stored in S2. Depending on the distance, the ratio between S1 and S2 changes as depicted in the drawing.[4] Because only small amounts of light hit the sensor within 50 ns, not only one but several thousand pulses are sent out (repetition rate tR) and gathered, thus increasing the signal-to-noise ratio.

After the exposure, the pixel is read out and the following stages measure the signals S1 and S2. As the length of the light pulse is defined, the distance can be calculated with the formula:

D={\frac {1}{2}}\cdot c\cdot t_{0}\cdot {\frac {S2}{S1+S2}}

In the example, the signals have the following values: S1 = 0.66 and S2 = 0.33. The distance is therefore:

D=7.5\;\mathrm {m} \cdot {\frac {0.33}{0.33+0.66}}=2.5\;\mathrm {m}

In the presence of background light, the memory elements receive an additional part of the signal. This would disturb the distance measurement. To eliminate the background part of the signal, the whole measurement can be performed a second time with the illumination switched off. If the objects are further away than the distance range, the result is also wrong. Here, a second measurement with the control signals delayed by an additional pulse width helps to suppress such objects. Other systems work with a sinusoidally modulated light source instead of the pulse source.

For direct TOF imagers, such as 3D Flash LIDAR, a single short pulse from 5 to 10 ns is emitted by the laser. The T-zero event (the time the pulse leaves the camera) is established by capturing the pulse directly and routing this timing onto the focal plane array. T-zero is used to compare the return time of the returning reflected pulse on the various pixels of the focal plane array. By comparing T-zero and the captured returned pulse and comparing the time difference, each pixel accurately outputs a direct time-of-flight measurement. The round trip of a single pulse for 100 meters is 660 ns. With a 10 ns pulse, the scene is illuminated and the range and intensity captured in less than 1 microsecond.

Advantages

Simplicity

In contrast to stereo vision or triangulation systems, the whole system is very compact: the illumination is placed just next to the lens, whereas the other systems need a certain minimum base line. In contrast to laser scanning systems, no mechanical moving parts are needed.

Efficient distance algorithm

It is a direct process to extract the distance information out of the output signals of the TOF sensor. As a result, this task uses only a small amount of processing power, again in contrast to stereo vision, where complex correlation algorithms are implemented. After the distance data has been extracted, object detection, for example, is also a straightforward process to carry out because the algorithms are not disturbed by patterns on the object. The accuracy is usually estimated at 1 % of the measured distance.[18][19]

Speed

Time-of-flight cameras are able to measure the distances within a complete scene with a single shot. As the cameras reach up to 160 frames per second, they are ideally suited to be used in real-time applications.

Disadvantages

Background light

When using CMOS or other integrating detectors or sensors that use visible or near infra-red light (400 nm - 700 nm), although most of the background light coming from artificial lighting or the sun is suppressed, the pixel still has to provide a high dynamic range. The background light also generates electrons, which have to be stored. For example, the illumination units in many of today's TOF cameras can provide an illumination level of about 1 watt. The Sun has an illumination power of about 1050 watts per square meter, and 50 watts after the optical band-pass filter. Therefore, if the illuminated scene has a size of 1 square meter, the light from the sun is 50 times stronger than the modulated signal. For non-integrating TOF sensors that do not integrate light over time and are using near-infrared detectors (InGaAs) to capture the short laser pulse, direct viewing of the sun is a non-issue because the image is not integrated over time, rather captured within a short acquisition cycle typically less than 1 microsecond. Such TOF sensors are used in space applications[12] and in consideration for automotive applications.[20]

Interference

In certain types of TOF devices (but not all of them), if several time-of-flight cameras are running at the same time, the TOF cameras may disturb each other's measurements. There exist several possibilities for dealing with this problem:

Time multiplexing: A control system starts the measurement of the individual cameras consecutively, so that only one illumination unit is active at a time.
Different modulation frequencies: If the cameras modulate their light with different modulation frequencies, their light is collected in the other systems only as background illumination but does not disturb the distance measurement.

For Direct TOF type cameras that use a single laser pulse for illumination, because the single laser pulse is short (e.g. 10 nanoseconds), the round trip TOF to and from the objects in the field of view is correspondingly short (e.g. 100 meters = 660 ns TOF round trip). For an imager capturing at 30 Hz, the probability of an interfering interaction is the time that the camera acquisition gate is open divided by the time between laser pulses or approximately 1 in 50,000 (0.66 μs divided by 33 ms).

Multiple reflections

In contrast to laser scanning systems where a single point is illuminated, the time-of-flight cameras illuminate a whole scene. For a phase difference device (amplitude modulated array), due to multiple reflections, the light may reach the objects along several paths. Therefore, the measured distance may be greater than the true distance. Direct TOF imagers are vulnerable if the light is reflecting from a specular surface. There are published papers available that outline the strengths and weaknesses of the various TOF devices and approaches.[21]

Applications

Range image of a human face captured with a time-of-flight camera (artist’s depiction)

Automotive applications

Time-of-flight cameras are used in assistance and safety functions for advanced automotive applications such as active pedestrian safety, precrash detection and indoor applications like out-of-position (OOP) detection.[22][23]

Human-machine interfaces and gaming

As time-of-flight cameras provide distance images in real time, it is easy to track movements of humans. This allows new interactions with consumer devices such as televisions. Another topic is to use this type of cameras to interact with games on video game consoles.[24] The second-generation Kinect sensor originally included with the Xbox One console used a time-of-flight camera for its range imaging,[25] enabling natural user interfaces and gaming applications using computer vision and gesture recognition techniques. Creative and Intel also provide a similar type of interactive gesture time-of-flight camera for gaming, the Senz3D based on the DepthSense 325 camera of Softkinetic.[26] Infineon and PMD Technologies enable tiny integrated 3D depth cameras for close-range gesture control of consumer devices like all-in-one PCs and laptops (Picco flexx and Picco monstar cameras).[27]

Smartphone cameras

The Samsung Galaxy S20 Ultra features three rear-facing camera lenses and a ToF camera.

Several smartphones include time-of-flight cameras. These are mainly used to improve the quality of photos by providing the camera software with information about foreground and background.[28]

The first mobile phone released with such technology was the LG G3, from early 2014.[29] The BlackBerry Passport and the LG G Flex 2 were also launched with a ToF sensor.[30]

Measurement and machine vision

Range image with height measurements

Other applications are measurement tasks, e.g. for the fill height in silos. In industrial machine vision, the time-of-flight camera helps to classify and locate objects for use by robots, such as items passing by on a conveyor. Door controls can distinguish easily between animals and humans reaching the door.

Robotics

Another use of these cameras is the field of robotics: Mobile robots can build up a map of their surroundings very quickly, enabling them to avoid obstacles or follow a leading person. As the distance calculation is simple, only little computational power is used. Since these cameras can also be used to measure distance, teams for FIRST Robotics Competition have been known to use the devices for autonomous routines.

Earth topography

ToF cameras have been used to obtain digital elevation models of the Earth's surface topography,[31] for studies in geomorphology.

Brands

Active brands (as of 2011)

ESPROS - 3D TOF imager chips, TOF camera and module for automotive, robotics, industrial and IoT applications
3D Flash LIDAR Cameras and Vision Systems by Advanced Scientific Concepts, Inc. for aerial, automotive and space applications
DepthSense - TOF cameras and modules, including RGB sensor and microphones by SoftKinetic
IRMA MATRIX - TOF camera, used for automatic passenger counting on mobile and stationary applications by iris-GmbH
Kinect - hands-free user interface platform by Microsoft for video game consoles and PCs, using time-of-flight cameras in its second generation of sensor devices.[25]
pmd - camera reference designs and software (pmd[vision], including TOF modules [CamBoard]) and TOF imagers (PhotonICs) by PMD Technologies
real.IZ 2+3D - High-resolution SXGA (1280×1024) TOF camera developed by startup company odos imaging, integrating conventional image capture with TOF ranging in the same sensor. Based on technology developed at Siemens.
Senz3D - TOF camera by Creative and Intel based on DepthSense 325 camera of Softkinetic, used for gaming.[26]
SICK - 3D industrial TOF cameras (Visionary-T) for industrial applications and software[32]
3D MLI Sensor - TOF imager, modules, cameras, and software by IEE (International Electronics & Engineering), based on modulated light intensity (MLI)
TOFCam Stanley - TOF camera by Stanley Electric
TriDiCam - TOF modules and software, the TOF imager originally developed by Fraunhofer Institute of Microelectronic Circuits and Systems, now developed by the spin out company TriDiCam
Hakvision - TOF stereo camera
Cube eye - ToF Camera and Modules, VGA Resolution, website : www.cube-eye.co.kr

Defunct brands

CanestaVision[33] - TOF modules and software by Canesta (company acquired by Microsoft in 2010)
D-IMager - TOF camera by Panasonic Electric Works
OptriCam - TOF cameras and modules by Optrima (rebranded DepthSense prior to SoftKinetic merger in 2011)
ZCam - TOF camera products by 3DV Systems, integrating full-color video with depth information (assets sold to Microsoft in 2009)
SwissRanger - an industrial TOF-only camera line originally by the Centre Suisse d'Electronique et Microtechnique, S.A. (CSEM), now developed by Mesa Imaging (Mesa Imaging acquired by Heptagon in 2014)
Fotonic - TOF cameras and software powered by Panasonic CMOS chip (Fotonic acquired by Autoliv in 2018)
S.Cube - ToF Camera and Modules by Cube eye

D-IMager by Panasonic
pmd[vision] CamCube by PMD Technologies
SwissRanger 4000 by MESA Imaging
FOTONIC-B70 by Fotonic
3D MLI Sensor by IEE S.A.
ARTTS camera prototype
pmd[vision] CamBoard by PMD Technologies
Kinect for Xbox One by Microsoft

References

Iddan, Gavriel J.; Yahav, Giora (2001-01-24). "3D imaging in the studio (and elsewhere…)" (PDF). Proceedings of SPIE. Vol. 4298. San Jose, CA: SPIE (published 2003-04-29). p. 48. doi:10.1117/12.424913. Archived from the original (PDF) on 2009-06-12. Retrieved 2009-08-17. The [time-of-flight] camera belongs to a broader group of sensors known as scanner-less LIDAR (i.e. laser radar having no mechanical scanner); an early [1990] example is [Marion W.] Scott and his followers at Sandia.
"Product Evolution". 3DV Systems. Archived from the original on 2009-02-28. Retrieved 2009-02-19. Z-Cam, the first depth video camera, was released in 2000 and was targeted primarily at broadcasting organizations.
Christoph Heckenkamp: Das magische Auge - Grundlagen der Bildverarbeitung: Das PMD Prinzip. In: Inspect. Nr. 1, 2008, S. 25–28.
Gokturk, Salih Burak; Yalcin, Hakan; Bamji, Cyrus (24 January 2005). "A Time-Of-Flight Depth Sensor - System Description, Issues and Solutions" (PDF). IEEE Computer Society Conference on Computer Vision and Pattern Recognition Workshops, 2004: 35–45. doi:10.1109/CVPR.2004.291. S2CID 1203932. Archived from the original (PDF) on 2007-06-23. Retrieved 2009-07-31. The differential structure accumulates photo-generated charges in two collection nodes using two modulated gates. The gate modulation signals are synchronized with the light source, and hence depending on the phase of incoming light, one node collects more charges than the other. At the end of integration, the voltage difference between the two nodes is read out as a measure of the phase of the reflected light.
"Mesa Imaging - Products". August 17, 2009.
US patent 5081530, Medina, Antonio, "Three Dimensional Camera and Rangefinder", issued 1992-01-14, assigned to Medina, Antonio
Medina A, Gayá F, Pozo F (2006). "Compact laser radar and three-dimensional camera". J. Opt. Soc. Am. A. 23 (4): 800–805. Bibcode:2006JOSAA..23..800M. doi:10.1364/JOSAA.23.000800. PMID 16604759.
"Kinect for Windows developer's kit slated for November, adds 'green screen' technology". PCWorld. 2013-06-26.
"Submillimeter 3-D Laser Radar for Space Shuttle Tile Inspection.pdf" (PDF).
"Sea-Lynx Gated Camera - active laser camera system" (PDF). Archived from the original (PDF) on 2010-08-13.
Reisse, Robert; Amzajerdian, Farzin; Bulyshev, Alexander; Roback, Vincent (4 June 2013). Turner, Monte D; Kamerman, Gary W (eds.). "Helicopter flight test of 3D imaging flash LIDAR technology for safe, autonomous, and precise planetary landing" (PDF). Laser Radar Technology and Applications XVIII. 8731: 87310H. Bibcode:2013SPIE.8731E..0HR. doi:10.1117/12.2015961. hdl:2060/20130013472. S2CID 15432289.
"ASC's 3D Flash LIDAR camera selected for OSIRIS-REx asteroid mission". NASASpaceFlight.com. 2012-05-13.
http://e-vmi.com/pdf/2012_VMI_AUVSI_Report.pdf
"Autonomous Aerial Cargo/Utility System Program". Office of Naval Research. Archived from the original on 2014-04-06.
"Products". Advanced Scientific Concepts.
"Time-of-Flight Camera â€" An Introduction". Mouser Electronics.
"CCD/CMOS Lock-In Pixel for Range Imaging: Challenges, Limitations and State-of-the-Art" - CSEM
Wang, John (2022-03-04). "Time of Flight Sensor: What It Is and How it Works". PCB Assembly,PCB Manufacturing,PCB design - OURPCB. Retrieved 2023-04-14.
Hansard, Miles; Lee, Seungkyu; Choi, Ouk; Horaud, Radu (2012-10-31). Time of Flight Cameras: Principles, Methods, and Applications. Springer. p. 20.
"Automotive". Advanced Scientific Concepts.
Aue, Jan; Langer, Dirk; Muller-Bessler, Bernhard; Huhnke, Burkhard (2011-06-09). "2011 IEEE Intelligent Vehicles Symposium (IV)". 2011 IEEE Intelligent Vehicles Symposium (IV). Baden-Baden, Germany: IEEE. pp. 423–428. doi:10.1109/ivs.2011.5940442. ISBN 978-1-4577-0890-9.
Hsu, Stephen; Acharya, Sunil; Rafii, Abbas; New, Richard (25 April 2006). "Performance of a Time-of-Flight Range Camera for Intelligent Vehicle Safety Applications". Advanced Microsystems for Automotive Applications 2006 (PDF). VDI-Buch. Springer. pp. 205–219. CiteSeerX 10.1.1.112.6869. doi:10.1007/3-540-33410-6_16. ISBN 978-3-540-33410-1. Archived from the original (PDF) on 2006-12-06. Retrieved 2018-06-25.
Elkhalili, Omar; Schrey, Olaf M.; Ulfig, Wiebke; Brockherde, Werner; Hosticka, Bedrich J. (September 2006), "A 64x8 pixel 3-D CMOS time-of flight image sensor for car safety applications", European Solid State Circuits Conference 2006, pp. 568–571, doi:10.1109/ESSCIR.2006.307488, ISBN 978-1-4244-0302-8, S2CID 24652659, retrieved 2010-03-05
Captain, Sean (2008-05-01). "Out of Control Gaming". PopSci.com. Popular Science. Retrieved 2009-06-15.
Rubin, Peter (2013-05-21). "Exclusive First Look at Xbox One". Wired. Wired Magazine. Retrieved 2013-05-22.
Sterling, Bruce (2013-06-04). "Augmented Reality: SoftKinetic 3D depth camera and Creative Senz3D Peripheral Camera for Intel devices". Wired Magazine. Retrieved 2013-07-02.
Lai, Richard. "PMD and Infineon to enable tiny integrated 3D depth cameras (hands-on)". Engadget. Retrieved 2013-10-09.
Heinzman, Andrew (2019-04-04). "What Is a Time of Flight (ToF) Camera, and Why Does My Phone Have One?". How-To Geek.
James, Dick (2016-10-17). "STMicroelectronics' Time-of-Flight Sensors and the Starship Enterprise Show up in the iPhone 7 Series". TechInsights. Archived from the original on 2022-12-25. Retrieved 2023-05-21.
Frank, Randy (2014-10-17). "Time-of-flight Technology Designed into Smartphone". Sensor Tips. WTWH Media LLC. Archived from the original on 2023-04-19. Retrieved 2023-05-21.
Nitsche, M.; Turowski, J. M.; Badoux, A.; Rickenmann, D.; Kohoutek, T. K.; Pauli, M.; Kirchner, J. W. (2013). "Range imaging: A new method for high-resolution topographic measurements in small- and medium-scale field sites". Earth Surface Processes and Landforms. 38 (8): 810. Bibcode:2013ESPL...38..810N. doi:10.1002/esp.3322. S2CID 55282788.
TBA. "SICK - Visionary-T y Visionary-B: 3D de un vistazo - Handling&Storage". www.handling-storage.com (in European Spanish). Retrieved 2017-04-18.
"TowerJazz CIS Technology Selected by Canesta for Consumer 3-D Image Sensors". Business Wire. 21 June 2010. Retrieved 2013-10-29. Canesta Inc. is using TowerJazz's CMOS image sensor (CIS) technology to manufacture its innovative CanestaVision 3-D image sensors.