Pump-jet

This image illustrates the workings of a reversing bucket. 1: Forward thrust, reversing bucket disengaged 2: Reverse thrust, reversing bucket pushes the thrust flow backwards

Forward, back, side and turn by pump-jet

A pump-jet works by having an intake (usually at the bottom of the hull) that allows water to pass underneath the vessel into the engines. Water enters the pump through this inlet. The pump can be of a centrifugal design for high speeds, or an axial flow pump for low to medium speeds. The water pressure inside the inlet is increased by the pump and forced backwards through a nozzle. With the use of a reversing bucket, reverse thrust can also be achieved for faring backwards, quickly and without the need to change gear or adjust engine thrust. The reversing bucket can also be used to help slow the ship down when braking. This feature is the main reason pump jets are so maneuverable.

The nozzle also provides the steering of the pump-jets. Plates, similar to rudders, can be attached to the nozzle in order to redirect the water flow port and starboard. In a way, this is similar to the principles of air thrust vectoring, a technique which has long been used in launch vehicles (rockets and missiles) then later in military jet-powered aircraft. This provides pumpjet-powered ships with superior agility at sea. Another advantage is that when faring backwards by using the reversing bucket, steering is not inverted, as opposed to propeller-powered ships.

Pump jets have some advantages over bare propellers for certain applications, usually related to requirements for high-speed or shallow-draft operations. These include:

• Higher speed before the onset of cavitation, because of the raised internal dynamic pressure
• High power density (with respect to volume) of both the propulsor and the prime mover (because a smaller, higher-speed unit can be used)
• Protection of the rotating element, making operation safer around swimmers and aquatic life
• Improved shallow-water operations, because only the inlet needs to be submerged
• Increased maneuverability, by adding a steerable nozzle to create vectored thrust
• Noise reduction, resulting in a low sonar signature; this particular system has little in common with other pump-jet propulsors and is also known as "shrouded propeller configuration";[3] applications:
  • Warships designed for low observability, for example the Swedish Visby-class corvette.
  • Submarines, for example the Royal Navy Trafalgar class and Astute class, the US Navy Seawolf class and Virginia class, the French Navy Triomphant class and Barracuda class, and the Russian Navy Borei class.
  • Modern torpedoes, such as the Spearfish, the Mk 48 and Mk 50 weapons.

The water jet principle in shipping industry can be traced back to 1661[4] when Toogood and Hayes produced a description of a ship having a central water channel in which either a plunger or centrifugal pump was installed to provide the motive power.[5]

On December 3, 1787, inventor James Rumsey demonstrated a water-jet propelled boat using a steam-powered pump to drive a stream of water from the stern.[6] This occurred on the Potomac River at Shepherdstown, Virginia (now West Virginia) before a crowd of witnesses including General Horatio Gates. The 50-foot long boat traveled about one-half mile upriver before returning to the dock. The boat was reported to reach a speed of four mph moving upstream.[7][8][9]

In April 1932, Italian engineer Secondo Campini demonstrated a pump-jet propelled boat in Venice, Italy. The boat achieved a top speed of 28 knots (32 mph; 52 km/h), a speed comparable to a boat with a conventional engine of similar output. The Italian Navy, who had funded the development of the boat, placed no orders but did veto the sale of the design outside of Italy.[10][11] The first modern jetboat was developed by New Zealand engineer Sir William Hamilton in the mid 1950s.[12]

Pump-jets were once limited to high-speed pleasure craft (such as jet skis and jetboats) and other small vessels, but since 2000 the desire for high-speed vessels has increased and thus the pump-jet is gaining popularity on larger craft, military vessels and ferries. On these larger craft, they can be powered by diesel engines or gas turbines. Speeds of up to 40 knots (45 mph; 75 km/h) can be achieved with this configuration, even with a displacement hull.[13]

Pump-jet powered ships are very maneuverable. Examples of ships using pumpjets are the Car Nicobar-class patrol vessels, the Hamina-class missile boats, Valour-class frigates, the Stena high-speed sea service ferries, the United States Seawolf-class and Virginia-class, as well as the Russian Borei-class submarines and the United States littoral combat ships.

• Internal drive propulsion
• Personal water craft
• Wetbike
• Kitchen rudder
• Water rocket
• Chain boat - Water turbines