Pan–Tompkins algorithm

As a first step, a band-pass filter is applied to increase the signal-to-noise ratio. A filter bandwidth of 5-15 Hz is suggested to maximize the QRS contribute and reduce muscle noise, baseline wander, powerline interference and the P wave/T wave frequency content.[1] In the original algorithm proposed in 1985, the band-pass filter was obtained with a low-pass filter and a high-pass filter in cascade to reduce the computational cost and allow a real-time detection, while ensuring a 3 dB passband in the 5–12 Hz frequency range, reasonably close to the design goal.

For a signal sampled at a frequency of 200 Hz, Pan and Tompkins suggested the filters with the following transfer functions ${\displaystyle H(z)}$ in an updated version of their article:[4]

• ${\displaystyle H(z)={(1-z^{-6})^{2} \over (1-z^{-1})^{2}}}$ for a second-order low-pass filter with a gain of 36 and a processing delay of 6 samples;
• ${\displaystyle H(z)={(-1/32+z^{-16}-z^{-17}+z^{-32}/32) \over (1-z^{-1})}}$for a high-pass filter with a unitary gain and a processing delay of 16 samples.

As a third step, a derivative filter is applied to provide information about the slope of the QRS. For a signal sampled at 200 Hz, Pan and Tompkins suggested the following transfer function:[4]

${\displaystyle H(z)=0.1(-z^{-2}-2z^{-1}+2z^{1}+z^{2})}$for a 5-point derivative filter with gain of 0.1 and a processing delay of 2 samples.

The filtered signal is squared to enhance the dominant peaks (QRSs) and reduce the possibility of erroneously recognizing a T wave as an R peak. Then, a moving average filter is applied to provide information about the duration of the QRS complex. The number of samples to average is chosen in order to average on windows of 150 ms.[1] The signal so obtained is called integrated signal.

In order to detect a QRS complex, the local peaks of the integrated signal are found. A peak is defined as the point in which the signal changes direction (from an increasing direction to a decreasing direction). After each peak, no peak can be detected in the next 200 ms (ie. the lockout time). This is a physiological constraint due to the refractory period during which ventricular depolarization cannot occur even in the presence of a stimulus.[1]

Each fiducial mark is considered as a potential QRS. To reduce the possibility of wrongly selecting a noise peak as a QRS, each peak amplitude is compared to a threshold (Threshold_I) that takes into account the available information about already detected QRS and the noise level:

${\displaystyle Threshold_{I}=NoiseLevel_{I}+0.25(SignalLevel_{I}-NoiseLevel_{I})}$

where NoiseLevel_I is the running estimate of the noise level in the integrated signal and SignalLevel_I is the running estimate of the signal level in the integrated signal.

The threshold is automatically updated after detecting a new peak, based on its classification as signal or noise peak:

${\displaystyle SignalLevel_{I}=0.125PEAK_{I}+0.875SignalLevel_{I}}$(if PEAK_I is a signal peak)

${\displaystyle NoiseLevel_{I}=0.125PEAK_{I}+0.875NoiseLevel_{I}}$(if PEAK_I is a noise peak)

where PEAK_I is the new peak found in the integrated signal.

At the beginning of the QRS detection, a 2 seconds learning phase is needed to initialize SignalLevel_I and NoiseLevel_I as a percentage of the maximum and average amplitude of the integrated signal, respectively.

If a new PEAK_I is under the Threshold_I, the noise level is updated. If PEAK_I is above the Threshold_I, the algorithm implements a further check before confirming the peak as a true QRS, taking into consideration the information provided by the bandpass filtered signal.

In the filtered signal the peak corresponding to the one evaluated on the integrated signal is searched and compared with a threshold, calculated in a similar way to the previous step:

${\displaystyle Threshold_{F}=NoiseLevel_{F}+0.25(SignalLevel_{F}-NoiseLevel_{F})}$

${\displaystyle SignalLevel_{F}=0.125PEAK_{F}+0.875SignalLevel_{F}}$(if PEAK_F is a signal peak)

${\displaystyle NoiseLevel_{F}=0.125PEAK_{F}+0.875NoiseLevel_{F}}$(if PEAK_F is a noise peak)

where the final F stands for filtered signal.

The algorithm takes into account the possibility of setting too high values of ThresholdI_I and ThresholdI_F. A check is performed to continuously assess the RR intervals (namely the temporal interval between two consecutively QRS peaks) to overcome this issue. The average RR is computed in two ways to consider both regular and irregular heart rhythm. In the first method RRaverage1 is computed as the mean of the last RR intervals. In the second method RRaverage2 is computed as the mean of the last RR intervals that fell between the limits specified as:

${\displaystyle RRlow=92\%RRaverage2}$

${\displaystyle RRhigh=116\%RRaverage2}$

If no QRS is detected in a window of 166% of the average RR (RRaverage1 or RRaverage2, if the heart rhythm is regular or irregular, respectively), the algorithm adds the maximal peak in the window as a potential QRS and classify it considering half the values of the thresholds (both ThresholdI_I and ThresholdI_F). This check is implemented because the temporal distance between two consecutive beats cannot physiologically change more quickly than this.

The algorithm takes particularly into consideration the possibility of a false detection of T waves. If a potential QRS falls up to a 160 ms window after the refractory periody from the last correctly detected QRS complex, the algorithm evaluates if it could be a T wave with particular high amplitude. In this case, its slope is compared to the one of the precedent QRS complex. If the slope is less than half the previous one, the current QRS is recognized as a T wave and discarded, and it also updates the NoiseLevel (both in the filtered signal and the integrated signal).