Protein corona

To determine how the protein composition and concentration affects protein coronas, one study incubated silica nanoparticles in plasma medium for 1 hr and observed the formation of the corona.[3] They found that the proteins adsorbed easily to the silica surface and expressed themselves in different patterns depending on the amount of plasma present in the incubated medium.[3] The experiment was run with 3%, 20%, and 80% plasma, and it was discovered that in the case of plasma, where there is a much higher concentration of lower-affinity proteins than high-affinity proteins, the lower-affinity proteins had a tendency to replace the higher-affinity proteins on the surface of the nanoparticle because of their higher abundance within the plasma.[3] From studies like these, it is clear that a protein corona can be altered significantly, depending on the weight and affinity of the biological molecules in a particular medium.[3]

Another major factor that affects protein coronas is exposure time, or the amount of time a nanoparticle coated in proteins is exposed to fluidic media.[4] Since it is well known that instantly upon introduction of a nanoparticle to a biomolecular medium, a protein corona forms on its surface, one study exposed nanoparticles to biological fluids like human plasma and observed how the length of exposure to these mediums can affect the formation of the corona.[4] After only 30 seconds of interaction, almost 300 proteins were detected adsorbing to the nanoparticle surface, and a majority of those molecules had low affinity (pharmacology) and a large molecular weight.[4] After 1 minute or more of exposure, different protein corona patterns were observed, and of the proteins detected, most of them had a higher affinity and smaller molecular weight, consistent with the Vroman effect.[4] Thus, the length of the exposure time of the nanoparticle to biological fluid can greatly alter the composition and patterns of the protein corona.

In addition to exposure time is the factor of shearing forces. In the past, researchers studied protein-nanoparticle interactions under very static conditions so that variables could be easily controlled. However, these conditions are not very representative of the conditions of the human body where nanoparticles will generally be exposed to shearing stresses and hydrodynamic fluid conditions.[5] Thus, experiments that accounted for fluidic conditions were necessary to understand how protein coronas would endure in the human body. One study found that fluidic flow increased the biodiversity of the protein corona and altered its shape due to the shearing forces present in the environment.[5] Because both of these factors have implications in the functionalization of protein corona nanoparticles, these observations proved the importance of studying protein coronas in the presence of fluidic conditions.

Temperature can also greatly affect protein-nanoparticle interactions. A study performed on Cu nanoparticles showed that as the ambient temperature of the nanoparticles was increased from 15 °C, 27 °C, and 37 °C to 42 °C, the amount of protein adsorbed to the nanoparticle surface also increased.[6] This finding was especially interesting in the effort to utilize protein coronas to treat illnesses, because in introducing these particles into the human body, they will have to exist and function at high temperatures. In feverish individuals, their altered body temperature may potentially change the biodistribution and bio-availability of the nanoparticles.[6] Thus, it is important for researchers to account for temperature effects on protein coronas.[6]

The environmental pH can also affect protein corona formation. It is known that pH is an important factor to be considered when studying the properties and functionality of proteins. pH can alter protein binding affinity in protein-nanoparticle interactions, thus modifying the adsorbed protein pattern at the surface of the nanoparticle.[7][8] If used for drug delivery methods, the nanoparticles will have to undergo multiple different pH changes in the cellular uptake pathway like blood (neutral pH), exposure media (pH 6.9-7.4), intracellular fluid (pH 6.8), and lysosomes (pH 4.5-5) and be able to keep its corona intact and functional.[7][8] Cancer tumors especially are known to induce acidic microenvironments as well as contain certain types of proteins that are capable of modifying the protein corona around nanoparticles which can greatly alter the body’s therapeutic response to drug molecules.[7]

Lastly, the composition of the nanoparticle itself can affect the protein corona formation at its surface. Differences in the hydrophilic or hydrophobic nature of the nanoparticle material can determine the amount of proteins in the corona.[9] Usually, proteins adsorb more easily to hydrophobic materials than hydrophilic materials.[9] As a result, hydrophobic nanoparticles are more likely to induce particle aggregation and higher opsonization in the human body, which can decrease systemic circulation time in the blood.[9]

Additionally, :) to aid in formation and solubility, nanoparticles often have ligands and functional groups on their surfaces that act like “fingerprints”.[9] Protein fingerprints refer to the ability to differentiate or identify proteins using ligands and other methods.[9] These fingerprints allow for nanoparticles to be tailored compositionally to adsorb specific proteins to their surfaces.[9] Nanoparticle surface roughness may also play a role in protein corona formation, since one study found that a rough nanoparticle surface can minimize repulsive interactions between the nanoparticle and parts of the binding proteins, which increases the amount of proteins adsorbed.[10]

Protein coronas can be utilized for a number of different functions, the main one being drug delivery. The corona that forms when nanoparticles come in contact with biological fluid has long been investigated for its potential to deliver important drug molecules or proteins to sites of need within the human body.[2] Nanoparticles are known to have high drug-loading efficiency as well as the ability to easily pass through biological barriers due to their nano scalability.[11][12] Their composition tunability allows for their toxicity to be controlled, and they can be modified to contain diverse sets of functional groups that can perform specific activities.[11][12] These qualities of nanoparticles make them ideal for drug delivery capabilities.

A major area of study within the sphere of protein corona drug delivery, is the study of the circulation time of nanoparticles in the body. In order to optimize the effectiveness of a drug, specifying the location where it is delivered and how long it stays there can be extremely useful.[13] Often, macrophages within the blood will detect the presence of the nanoparticles and immediately work to eliminate them from the body.[13][14] This is not always a good thing from the perspective of drug delivery, and thus studies were performed to prolong circulation time. It was found that when opsonins, like fibrinogen, are numerous in the protein corona, the proteins tend to induce macrophage recognition and subsequent consumption of nanoparticles.[13] Conversely, when the corona is saturated with dysopsonins, like albumin, the macrophages show decreased recognition of the particles and thus, circulation time of the particles is greatly increased.[13] This technique is loosely referred to as the "stealth effect".[13] By tailoring the contents of the protein corona, the length of time a nanoparticle stays in your body can be controlled.

As mentioned previously, nanoparticles can be grown with particular functional groups on their surfaces that induce chemoselectivity. Functional biomolecules like transferrin, insulin, and folic acid are commonly used in cancer-targeting drug delivery systems.[15] Other smaller molecules like anhydride, amine, carboxyl, and thiol can be used to direct nanoparticles to high cellular association with endothelial cells, pancreatic cells, and activated human macrophages.[15] Certain apolipoproteins, such as Apo E, ApoA1, and ApoB-100, could potentially functionalize nanoparticles to target the nervous system.[16][17]

Another more pressing problem with nanoparticle drug delivery is the tendency for nanoparticles to accumulate at the target site or in various organs, which can become toxic.[14] It is known that the size of nanoparticles dictates their distribution within the body, meaning that nanoparticles with different sizes will tend to accumulate in certain organs.[18] Therefore, size is a very important control factor when considering nanoparticle distribution and accumulation at target sites during drug delivery.[18]