Firing pin

Animation of a Dreyse needle gun firing, with its peculiar needle firing-pin.

The two main types of metallic cartridges used in modern firearms are centerfire and rimfire. In centerfire cartridges, the primer is located in the center of the base of the cartridge. Firing pins for centerfire cartridges usually have a round cross-section and their movement is usually through a hole in the breechblock along the axis of the center of the barrel's bore.

Rimfire cartridges however, must be struck on the base about the rim of the cartridge. While rimfire firearms may use a firing pin with a round cross-section, it is common for them to be flat, with a square or rectangular cross-section and a blunt chisel point. Flat firing pins can be stamped from flat metal stock and usually operate in a slot cut in the breechblock (rather than a hole) that is parallel but offset from the centerline of the barrel. These production methods are generally simpler and reduce production costs. It is generally recommended not to excessively "dry fire" rimfire firearms (ie firing without a chambered round) as it is possible for the firing pin to strike the face of the camber and deform it or damage the firing pin.

A Lefaucheux M1858 pinfire pistol. Note the pin protruding from the cartridge.

In 1808 by the Swiss gunsmith Jean Samuel Pauly in association with French gunsmith François Prélat created the first cartridges to integrate a primer and be self-contained. The paper cartridge used a metal base with a through-hole coated in a percussive priming compound. Pauly also developed a breech-loading shotgun for his cartridge, using a firing pin and external hammer.[1]

The Dreyse needle gun of 1836 uses a paper cartridge with a priming as part of a sabot which cradles the projectile and is forward of the propelling charge. The needle-like firing-pin projects from the bolt-face and pierces the cartridge when the breech is closed. On firing, the spring-loaded needle strikes the priming in the sabot. Unlike Pauly's cartridge, which was not widely accepted, Dreyse's rifle was adopted by Prussia as its infantry service rifle. It was the first military breechloader to use a self-contained cartridge and consequently, the first to employ a firing pin.[2][3]

The pinfire cartridge patented in 1835, uses a metallic cartridge with an integrated firing pin located radially near the base of the cartridge.[4] The pin needs to be aligned with a corresponding slot in the chamber; a disadvantage compared with rimfire and center fire cartridges that followed and that are also safer.[2][5]

Early rifle designs that fired metallic cartridges typically used a side-lock mechanism, with the hammer mounted to one side rather than inline with the axis of the barrel. In the trapdoor Springfield Model 1865 (and similar) the rear of the firing pin tube within the breechblock is angled away from the centerline of the barrel toward the hammer.[6] The Sharps rifle uses a firing pin block to solve this alignment problem. The block sits within a recess in the breechblock. When struck by the hammer, the whole block is propelled forward. That part of the block with the firing pin sits on the centerline of the barrel and strikes the primer.[7][8][9]

View down the barrel of a L16 81mm mortar, showing the fixed firing-pin.

Many revolvers use a firing pin that is fixed to the hammer. Simple blowback sub-machine guns that fire from the open-bolt position often have a fixed firing pin that protrudes from the face of the bolt. As the bolt fully closes on the breech the primer of the newly chambered round is struck, causing the cartridge to fire. The Owen and F1 submachine gun are examples that use bolt-face fixed firing-pins. Some mortars use a fixed firing pin mounted in the breech plug. When a mortar round is dropped down the barrel, a primer in the base of the mortar round strikes the firing pin and ignites the propelling charge.[10]

In firearms terminology, a floating firing pin is one which is unrestricted by a firing-pin return spring or similar. While it will be captive and unable to simply fall out, either forward or backward, it is otherwise free to slide within these stops. The trapdoor Springfield Model 1865 is an example of a floating firing pin.[11]

The bolt of a Mauser Gewehr 98 field stripped, showing the cock-on-open striker mechanism

Hammer-operated firing mechanisms use a relatively light firing pin and rely on a transfer of momentum received from a spring-loaded hammer, in the same fashion as a punch or chisel relays the blow from a mallet. In firearms terminology, a striker (or striker mechanism) derives the impact force to strike the primer from a spring acting directly upon the 'firing pin' - similar to a crossbow, where the striker (firing pin) is like the crossbow bolt (arrow). A striker mechanism is very common in bolt action firearms but not to the exclusion of a hammer-operated mechanisms. It will also be found in other actions where the breechblock reciprocates directly inline with the axis of the barrel.

A striker mechanism will consist of the striker spring (firing spring) and the striker. The striker spring is a relatively strong spring sufficient to initiate firing. A typical striker consists of a narrow striking point, a heavier section that acts as a spring guide for the striker spring, a shoulder to restrain the spring, and a catch piece which is engaged by the trigger sear to hold the spring under tension when "cocked" and ready to fire. The striker spring is compressed between the striker's shoulder and the rear of the breechblock. A striker may be assembled from several component; however, the stored energy in the striker spring is transferred directly to the striker and then to the primer without any intermediate transfer of energy or momentum. As striker mechanisms combine both functions of hammer and firing pin in one piece, they are generally considered to be mechanically simpler but are more robust in construction than a typical firing pin.[12]

Many small calibre rimfire bolt action rifles and some centerfire automatic weapons (e. g., vz. 58) may appear to have a striker-operated firing mechanism but are actually a type of linear hammer. The hammer can be likened to that of a pile driver and is mainly contained within the bolt. It is much like the striker already described except that the "hammer" upon which the firing spring acts and the firing pin are separate units. Confusingly, parts lists will often refer to this type of hammer as a "striker".[13]

Striker-fired (or similar) bolt action firearms may be classified as cock-on-close or cock-on-open.

When the breech is opened and retracted rearward, the striker is also carried rearward so that the striker catch passes over the trigger sear. When the bolt is pushed forward to close the breech, the striker catch is held by the trigger sear. The firer must close the bolt with sufficient force to overcome the force exerted by the cocking spring. Notably, the Lee–Enfield and Belgian Mauser cock on closing as do many small calibre rimfire bolt action rifles.

The breech of a bolt action rifle is opened by first rotating the bolt handle. In cock-on-open operation, this rotation acts on a cam (similar to the action of a screw thread) which retracts the striker, compressing the cocking spring and holding it there. When the cocking handle is rotated closed, the cocking cam disengages but the striker is retained in the cocked position by the trigger sear.

Introduced in the Mauser Model 1871, it significantly reduced the risk of accidental discharge upon closing.[14] The system of operation was widely adopted and is used almost exclusively in modern center-fire rifle designs. The Mauser Gewehr 98, the Mosin–Nagant and M1903 Springfield are examples of service rifles using this type of operation.