Simple machine

The idea of a simple machine originated with the Greek philosopher Archimedes around the 3rd century BC, who studied the Archimedean simple machines: lever, pulley, and screw.[2][13] He discovered the principle of mechanical advantage in the lever.[14] Archimedes' famous remark with regard to the lever: "Give me a place to stand on, and I will move the Earth," (Greek: δῶς μοι πᾶ στῶ καὶ τὰν γᾶν κινάσω)[15] expresses his realization that there was no limit to the amount of force amplification that could be achieved by using mechanical advantage. Later Greek philosophers defined the classic five simple machines (excluding the inclined plane) and were able to calculate their (ideal) mechanical advantage.[7] For example, Heron of Alexandria (c. 10–75 AD) in his work Mechanics lists five mechanisms that can "set a load in motion"; lever, windlass, pulley, wedge, and screw,[13] and describes their fabrication and uses.[16] However the Greeks' understanding was limited to the statics of simple machines (the balance of forces), and did not include dynamics, the tradeoff between force and distance, or the concept of work.

During the Renaissance the dynamics of the mechanical powers, as the simple machines were called, began to be studied from the standpoint of how far they could lift a load, in addition to the force they could apply, leading eventually to the new concept of mechanical work. In 1586 Flemish engineer Simon Stevin derived the mechanical advantage of the inclined plane, and it was included with the other simple machines. The complete dynamic theory of simple machines was worked out by Italian scientist Galileo Galilei in 1600 in Le Meccaniche (On Mechanics), in which he showed the underlying mathematical similarity of the machines as force amplifiers.[17][18] He was the first to explain that simple machines do not create energy, only transform it.[17]

The classic rules of sliding friction in machines were discovered by Leonardo da Vinci (1452–1519), but were unpublished and merely documented in his notebooks, and were based on pre-Newtonian science such as believing friction was an ethereal fluid. They were rediscovered by Guillaume Amontons (1699) and were further developed by Charles-Augustin de Coulomb (1785).[19]

If a simple machine does not dissipate energy through friction, wear or deformation, then energy is conserved and it is called an ideal simple machine. In this case, the power into the machine equals the power out, and the mechanical advantage can be calculated from its geometric dimensions.

Although each machine works differently mechanically, the way they function is similar mathematically.[20] In each machine, a force ${\displaystyle F_{\text{in}}\,}$ is applied to the device at one point, and it does work moving a load, ${\displaystyle F_{\text{out}}\,}$ at another point.[21] Although some machines only change the direction of the force, such as a stationary pulley, most machines multiply the magnitude of the force by a factor, the mechanical advantage

${\displaystyle \mathrm {MA} =F_{\text{out}}/F_{\text{in}}\,}$

that can be calculated from the machine's geometry and friction.

Simple machines do not contain a source of energy,[22] so they cannot do more work than they receive from the input force.[21] A simple machine with no friction or elasticity is called an ideal machine.[23][24][25] Due to conservation of energy, in an ideal simple machine, the power output (rate of energy output) at any time ${\displaystyle P_{\text{out}}\,}$ is equal to the power input ${\displaystyle P_{\text{in}}\,}$

${\displaystyle P_{\text{out}}=P_{\text{in}}\!}$

The power output equals the velocity of the load ${\displaystyle v_{\text{out}}\,}$ multiplied by the load force ${\displaystyle P_{\text{out}}=F_{\text{out}}v_{\text{out}}\!}$. Similarly the power input from the applied force is equal to the velocity of the input point ${\displaystyle v_{\text{in}}\,}$ multiplied by the applied force ${\displaystyle P_{\text{in}}=F_{\text{in}}v_{\text{in}}\!}$. Therefore,

${\displaystyle F_{\text{out}}v_{\text{out}}=F_{\text{in}}v_{\text{in}}\,}$

So the mechanical advantage of an ideal machine ${\displaystyle \mathrm {MA} _{\text{ideal}}\,}$ is equal to the velocity ratio, the ratio of input velocity to output velocity

${\displaystyle \mathrm {MA} _{\text{ideal}}={F_{\text{out}} \over F_{\text{in}}}={v_{\text{in}} \over v_{\text{out}}}\,}$

The velocity ratio is also equal to the ratio of the distances covered in any given period of time[26][27][28]

${\displaystyle {v_{\text{out}} \over v_{\text{in}}}={d_{\text{out}} \over d_{\text{in}}}\,}$

Therefore the mechanical advantage of an ideal machine is also equal to the distance ratio, the ratio of input distance moved to output distance moved

This can be calculated from the geometry of the machine. For example, the mechanical advantage and distance ratio of the lever is equal to the ratio of its lever arms.

The mechanical advantage can be greater or less than one:

• If ${\displaystyle \mathrm {MA} >1\,}$ the output force is greater than the input, the machine acts as a force amplifier, but the distance moved by the load ${\displaystyle d_{\text{out}}\,}$ is less than the distance moved by the input force ${\displaystyle d_{\text{in}}\,}$.
• If ${\displaystyle \mathrm {MA} <1\,}$ the output force is less than the input, but the distance moved by the load is greater than the distance moved by the input force.

In the screw, which uses rotational motion, the input force should be replaced by the torque, and the velocity by the angular velocity the shaft is turned.

All real machines have friction, which causes some of the input power to be dissipated as heat. If ${\displaystyle P_{\text{fric}}\,}$ is the power lost to friction, from conservation of energy

${\displaystyle P_{\text{in}}=P_{\text{out}}+P_{\text{fric}}\,}$

The mechanical efficiency ${\displaystyle \eta \,}$ of a machine (where ${\displaystyle 0<\eta \ <1}$) is defined as the ratio of power out to the power in, and is a measure of the frictional energy losses

${\displaystyle \eta \equiv {P_{\text{out}} \over P_{\text{in}}}\,}$

${\displaystyle P_{\text{out}}=\eta P_{\text{in}}\,}$

As above, the power is equal to the product of force and velocity, so

${\displaystyle F_{\text{out}}v_{\text{out}}=\eta F_{\text{in}}v_{\text{in}}\,}$

Therefore,

So in non-ideal machines, the mechanical advantage is always less than the velocity ratio by the product with the efficiency η. So a machine that includes friction will not be able to move as large a load as a corresponding ideal machine using the same input force.

A compound machine is a machine formed from a set of simple machines connected in series with the output force of one providing the input force to the next. For example, a bench vise consists of a lever (the vise's handle) in series with a screw, and a simple gear train consists of a number of gears (wheels and axles) connected in series.

The mechanical advantage of a compound machine is the ratio of the output force exerted by the last machine in the series divided by the input force applied to the first machine, that is

${\displaystyle \mathrm {MA} _{\text{compound}}={F_{{\text{out}}N} \over F_{\text{in1}}}\,}$

Because the output force of each machine is the input of the next, ${\displaystyle F_{\text{out1}}=F_{\text{in2}},\;F_{\text{out2}}=F_{\text{in3}},\ldots \;F_{{\text{out}}K}=F_{{\text{in}}K+1}}$, this mechanical advantage is also given by

${\displaystyle \mathrm {MA} _{\text{compound}}={F_{\text{out1}} \over F_{\text{in1}}}{F_{\text{out2}} \over F_{\text{in2}}}{F_{\text{out3}} \over F_{\text{in3}}}\ldots {F_{{\text{out}}N} \over F_{{\text{in}}N}}\,}$

Thus, the mechanical advantage of the compound machine is equal to the product of the mechanical advantages of the series of simple machines that form it

${\displaystyle \mathrm {MA} _{\text{compound}}=\mathrm {MA} _{1}\mathrm {MA} _{2}\ldots \mathrm {MA} _{N}\,}$

Similarly, the efficiency of a compound machine is also the product of the efficiencies of the series of simple machines that form it

${\displaystyle \eta _{\text{compound}}=\eta _{1}\eta _{2}\ldots \;\eta _{N}.\,}$

The screw's self-locking property is the reason for its wide use in threaded fasteners like bolts and wood screws

In many simple machines, if the load force F_out on the machine is high enough in relation to the input force F_in, the machine will move backwards, with the load force doing work on the input force.[29] So these machines can be used in either direction, with the driving force applied to either input point. For example, if the load force on a lever is high enough, the lever will move backwards, moving the input arm backwards against the input force. These are called "reversible", "non-locking" or "overhauling" machines, and the backward motion is called "overhauling".

However, in some machines, if the frictional forces are high enough, no amount of load force can move it backwards, even if the input force is zero. This is called a "self-locking", "nonreversible", or "non-overhauling" machine.[29] These machines can only be set in motion by a force at the input, and when the input force is removed will remain motionless, "locked" by friction at whatever position they were left.

Self-locking occurs mainly in those machines with large areas of sliding contact between moving parts: the screw, inclined plane, and wedge:

• The most common example is a screw. In most screws, applying torque to the shaft can cause it to turn, moving the shaft linearly to do work against a load, but no amount of axial load force against the shaft will cause it to turn backwards.
• In an inclined plane, a load can be pulled up the plane by a sideways input force, but if the plane is not too steep and there is enough friction between load and plane, when the input force is removed the load will remain motionless and will not slide down the plane, regardless of its weight.
• A wedge can be driven into a block of wood by force on the end, such as from hitting it with a sledge hammer, forcing the sides apart, but no amount of compression force from the wood walls will cause it to pop back out of the block.

A machine will be self-locking if and only if its efficiency η is below 50%:[29]

${\displaystyle \eta \equiv {\frac {F_{\text{out}}/F_{\text{in}}}{d_{\text{in}}/d_{\text{out}}}}<0.50\,}$

Whether a machine is self-locking depends on both the friction forces (coefficient of static friction) between its parts, and the distance ratio d_in/d_out (ideal mechanical advantage). If both the friction and ideal mechanical advantage are high enough, it will self-lock.

Machines are studied as mechanical systems consisting of actuators and mechanisms that transmit forces and movement, monitored by sensors and controllers. The components of actuators and mechanisms consist of links and joints that form kinematic chains.

Kinematic chains

Illustration of a four-bar linkage from Kinematics of Machinery, 1876

Simple machines are elementary examples of kinematic chains that are used to model mechanical systems ranging from the steam engine to robot manipulators. The bearings that form the fulcrum of a lever and that allow the wheel and axle and pulleys to rotate are examples of a kinematic pair called a hinged joint. Similarly, the flat surface of an inclined plane and wedge are examples of the kinematic pair called a sliding joint. The screw is usually identified as its own kinematic pair called a helical joint.

Two levers, or cranks, are combined into a planar four-bar linkage by attaching a link that connects the output of one crank to the input of another. Additional links can be attached to form a six-bar linkage or in series to form a robot.[24]

• Linkage (mechanical)
• Cam and follower mechanisms
• Gears and gear trains
• Mechanism (engineering)
• Rolamite, the only elementary machine discovered in the 20th century