Is it possible to SSH in to an RPi without a network connection?
I could imagine that you could do it using a LAN cable from the computer to the RPi or maybe using a USB cable.
I do actually have access to a network, however it doesn't allow incoming connections (even from local IP's) to any ports except 80 and 443 I would imagine.
No router + no screen + regular Ethernet cable + RPI 2 + Raspbian Lite 2018-11-13 + Ubuntu 18.10
First we must enable the SSH server on the Pi, which is disabled by default for security.
If you already have a shell on the Pi through a non-SSH method such as screen + keyboard or UART (see below), just run:
sudo systemctl enable ssh
sudo service sshd start
as explained at: SSH not working with fresh install This persists across boots.
Otherwise, insert he SD card on your host, and create a magic empty file named ssh file in the boot/ partition.
On Ubuntu hosts, it gets mounted automatically and you can do just:
sudo touch /media/$USER/boot/ssh
which you can confirm with:
lsblk
which contains:
mmcblk0 179:0 0 14.4G 0 disk
├─mmcblk0p1 179:1 0 43.9M 0 part /media/ciro/boot
└─mmcblk0p2 179:2 0 14.4G 0 part /media/ciro/rootfs
If you don't enable the SSHD daemon on the Pi then SSH connection will fail with:
ssh: connect to host 10.42.0.160 port 22: Connection refused
when we try it later on.
After enabling the SSH server
Next, boot the Pi, and link an Ethernet cable from your laptop directly to the Pi:
On Ubuntu 17.04 to work around this bug as mentioned on this answer you first need:
sudo apt-get install dnsmasq-base
On the host, open the network manager:
nm-connection-editor
And go:
+ sign (Add a new connection)
Find the IP of the Pi on host:
cat /var/lib/misc/dnsmasq.leases
outputs something like:
1532204957 b8:27:eb:0c:1f:69 10.42.0.160 raspberrypi 01:b8:27:eb:0c:1f:69
10.42.0.160 is the IP, then as usual:
ssh pi@10.42.0.160
I also have the following in my .bashrc:
piip() ( cat /var/lib/misc/dnsmasq.leases | cut -d ' ' -f 3; )
pissh() ( sshpass -p raspberry ssh "pi@$(piip)"; )
From inside the Pi, notice that it can access the internet normally through your host's other interfaces:
ping google.com
For example on my laptop, the Pi takes up the Ethernet, but the host is also connected to the internet through WiFi.
The crossover cable is not required if the host network card supports Auto MDI-X. This is the case for most recent hardware, including for example the 2012 Lenovo T430 I tested with, which has an "Intel® 82579LM Gigabit Network Connection" which documents support for Auto MDI-X.
Now you can also:
UART serial USB converter
This is an alternative to SSH if you just want to get a shell on the Pi: https://en.wikipedia.org/wiki/Serial_port
This does not use SSH or networking itself, but rather the older, simpler, more direct, more reliable, lower bandwidth, lower distance serial interface. The Pi won't have access to the Internet with this method.
Desktop computers still have a serial port which you can connect directly wire to wire with the Pi, but these are hidden in most laptops, and so we need to buy a cheap USB adapter. Here I've used: https://www.amazon.co.uk/gp/product/B072K3Z3TL See also: https://unix.stackexchange.com/questions/307390/what-is-the-difference-between-ttys0-ttyusb0-and-ttyama0-in-linux/367882#367882
First plug the SD card on the host, and edit the config.txt file present in the first partition to add:
enable_uart=1
as explained at: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=141195
This first partition contains the bootloader, its configuration files and the (Linux / your) kernel, config.txt being one of them. The second partition contains the actual Linux root filesystem.
Now connect your computer to the Pi as:
You only need to attach 3 cables:
This is also documented at: https://www.raspberrypi.org/documentation/usage/gpio/README.md
Be careful not to link the Ground to the 5V, I've already burned 2 UART to USB chips by doing that!
You don't need to connect the 5V to the 5V at all. I think you can power your Pi like that, but I've read that this is a bad idea, just use the usual USB power source.
Finally, plug the USB side of the connector to your host computer, and get a shell with:
sudo apt install screen
sudo usermod -a -G dialout $USER
screen /dev/ttyUSB0 115200
Exit with Ctrl-A \.
Here is a video by Adafruit showing it: https://www.youtube.com/watch?v=zUBPeoLW16Q
See also
Similar question on Stack Overflow: https://stackoverflow.com/questions/16040128/hook-up-raspberry-pi-via-ethernet-to-laptop-without-router
For me, the most convenient way is to use USB Tethering on my Android device, connect it to the raspberry and then SSH from my phone to the raspberry.
see this post SSH from Android to rPI using USB?
You can easily do it by connecting your pi to laptop via LAN cable. Please make sure that (at list while you are doing it first time) you have dhcp server working on your laptop and listening on LAN interface you are using to connect with pi. You need somehow assign address to raspberry.
The problem is that you want to connect 2 devices of the same type. But it's still possible. You can use a Crossover cable for this (Method 1), or you could use a switch or hub to automatic make a crossover connection (Method 2). Or just use a simple router (Method 3).
Make a connection possible
Method1:
Use a Crossover cable and connect your PC and PI:
An Ethernet crossover cable is a type of Ethernet cable used to connect computing devices together directly. Normal straight through or patch cables were used to connect from a host network interface controller (a computer or similar device) to a network switch, hub or router. A cable with connections that "cross over" was used to connect two devices of the same type: two hosts or two switches to each other. Owing to the inclusion of Auto-MDIX capability.
You need to connect the cables in the UTP cable like this: http://www.incentre.net/wp-content/uploads/2015/02/ethcablerj45cr.gif
Source: http://en.wikipedia.org/wiki/Ethernet_crossover_cable
Method2:
You also can use a modern twisted pair Ethernet cable to connect to your PI. But you need a hub or switch for this:
connections can be made with a straight-through cable by means of an MDI-X port, also known as an "internal crossover" or "embedded crossover" connection. Hub and switch ports with such internal crossovers are usually labelled as such, with "uplink" or "X". For example, 3Com usually labels their ports 1X, 2X, and so on. In some cases a button is provided to allow a port to act as either a normal or an uplink port.
Source: http://en.wikipedia.org/wiki/Ethernet_over_twisted_pair
More information:
Introduced in 1998, this made the distinction between uplink and normal ports and manual selector switches on older hubs and switches obsolete. If one or both of two connected devices has the automatic MDI/MDI-X configuration feature there is no need for crossover cables. Although Auto-MDIX was specified as an optional feature in the 1000BASE-T standard, in practice it is implemented widely on most interfaces. Besides the eventually agreed upon Automatic MDI/MDI-X, this feature may also be referred to by various vendor-specific terms including: Auto uplink and trade, Universal Cable Recognition and Auto Sensing.
Source: http://en.wikipedia.org/wiki/Ethernet_crossover_cable
Method 3
Use a Router and connect both the PI and PC to the Router.
Make the connection
Give them both an IP in the same range, for example:
PC: 192.168.1.10 Subnet: 255.255.255.0
PI: 192.168.1.11 Subnet: 255.255.255.0
You can find here how to do this: http://www.cyberciti.biz/faq/linux-configure-a-static-ip-address-tutorial/
Enable SSH
http://steve.dynedge.co.uk/2012/05/29/enabling-ssh-on-debian-raspberry-pi/
Connect to the PI
On Windows use for example Putty.
Other method:
You also can look here: http://www.linux-usb.org/usbnet/
