Electromagnetic pulse

EMP energy may be transferred in any of four forms:

• Electric field
• Magnetic field
• Electromagnetic radiation
• Electrical conduction

According to Maxwell's equations, a pulse of electric energy will always be accompanied by a pulse of magnetic energy. In a typical pulse, either the electric or the magnetic form will dominate.

In general, only radiation acts over long distances, with the magnetic and electric fields acting over short distances. There are a few exceptions, such as a solar magnetic flare.

A pulse of electromagnetic energy typically comprises many frequencies from very low to some upper limit depending on the source. The range defined as EMP, sometimes referred to as "DC to daylight", excludes the highest frequencies comprising the optical (infrared, visible, ultraviolet) and ionizing (X and gamma rays) ranges.

Some types of EMP events can leave an optical trail, such as lightning and sparks, but these are side effects of the current flow through the air and are not part of the EMP itself.

The waveform of a pulse describes how its instantaneous amplitude (field strength or current) changes over time. Real pulses tend to be quite complicated, so simplified models are often used. Such a model is typically described either in a diagram or as a mathematical equation.

Rectangular pulse

Double exponential pulse

Damped sinewave pulse

Most electromagnetic pulses have a very sharp leading edge, building up quickly to their maximum level. The classic model is a double-exponential curve which climbs steeply, quickly reaches a peak and then decays more slowly. However, pulses from a controlled switching circuit often approximate the form of a rectangular or "square" pulse.

EMP events usually induce a corresponding signal in the surrounding environment or material. Coupling usually occurs most strongly over a relatively narrow frequency band, leading to a characteristic damped sine wave. Visually it is shown as a high frequency sine wave growing and decaying within the longer-lived envelope of the double-exponential curve. A damped sinewave typically has much lower energy and a narrower frequency spread than the original pulse, due to the transfer characteristic of the coupling mode. In practice, EMP test equipment often injects these damped sinewaves directly rather than attempting to recreate the high-energy threat pulses.

In a pulse train, such as from a digital clock circuit, the waveform is repeated at regular intervals. A single complete pulse cycle is sufficient to characterise such a regular, repetitive train.

Lightning is unusual in that it typically has a preliminary "leader" discharge of low energy building up to the main pulse, which in turn may be followed at intervals by several smaller bursts.[7][8]

ESD events are characterized by high voltages of many kV, but small currents sometimes cause visible sparks. ESD is treated as a small, localized phenomenon, although technically a lightning flash is a very large ESD event. ESD can also be man-made, as in the shock received from a Van de Graaff generator.

An ESD event can damage electronic circuitry by injecting a high-voltage pulse, besides giving people an unpleasant shock. Such an ESD event can also create sparks, which may in turn ignite fires or fuel-vapour explosions. For this reason, before refueling an aircraft or exposing any fuel vapor to the air, the fuel nozzle is first connected to the aircraft to safely discharge any static.

The switching action of an electrical circuit creates a sharp change in the flow of electricity. This sharp change is a form of EMP.

Simple electrical sources include inductive loads such as relays, solenoids, and brush contacts in electric motors. These typically send a pulse down any electrical connections present, as well as radiating a pulse of energy. The amplitude is usually small and the signal may be treated as "noise" or "interference". The switching off or "opening" of a circuit causes an abrupt change in the current flowing. This can in turn cause a large pulse in the electric field across the open contacts, causing arcing and damage. It is often necessary to incorporate design features to limit such effects.

Electronic devices such as vacuum tubes or valves, transistors, Electric Car Motors and diodes can also switch on and off very quickly, causing similar issues. One-off pulses may be caused by solid-state switches and other devices used only occasionally. However, the many millions of transistors in a modern computer may switch repeatedly at frequencies above 1  GHz, causing interference that appears to be continuous.

A nuclear electromagnetic pulse is the abrupt pulse of electromagnetic radiation resulting from a nuclear explosion. The resulting rapidly changing electric fields and magnetic fields may couple with electrical/electronic systems to produce damaging current and voltage surges.[9]

The intense gamma radiation emitted can also ionize the surrounding air, creating a secondary EMP as the atoms of air first lose their electrons and then regain them.

NEMP weapons are designed to maximize such EMP effects as the primary damage mechanism, and some are capable of destroying susceptible electronic equipment over a wide area.

A high-altitude electromagnetic pulse (HEMP) weapon is a NEMP warhead designed to be detonated far above the Earth's surface. The explosion releases a blast of gamma rays into the mid-stratosphere, which ionizes as a secondary effect and the resultant energetic free electrons interact with the Earth's magnetic field to produce a much stronger EMP than is normally produced in the denser air at lower altitudes.

Non-nuclear electromagnetic pulse (NNEMP) is a weapon-generated electromagnetic pulse without use of nuclear technology. Devices that can achieve this objective include a large low-inductance capacitor bank discharged into a single-loop antenna, a microwave generator, and an explosively pumped flux compression generator. To achieve the frequency characteristics of the pulse needed for optimal coupling into the target, wave-shaping circuits or microwave generators are added between the pulse source and the antenna. Vircators are vacuum tubes that are particularly suitable for microwave conversion of high-energy pulses.[10]

NNEMP generators can be carried as a payload of bombs, cruise missiles (such as the CHAMP missile) and drones, with diminished mechanical, thermal and ionizing radiation effects, but without the consequences of deploying nuclear weapons.

The range of NNEMP weapons is much less than nuclear EMP. Nearly all NNEMP devices used as weapons require chemical explosives as their initial energy source, producing only one millionth the energy of nuclear explosives of similar weight.[11] The electromagnetic pulse from NNEMP weapons must come from within the weapon, while nuclear weapons generate EMP as a secondary effect.[12] These facts limit the range of NNEMP weapons, but allow finer target discrimination. The effect of small e-bombs has proven to be sufficient for certain terrorist or military operations. Examples of such operations include the destruction of electronic control systems critical to the operation of many ground vehicles and aircraft.[13]

The concept of the explosively pumped flux compression generator for generating a non-nuclear electromagnetic pulse was conceived as early as 1951 by Andrei Sakharov in the Soviet Union,[14] but nations kept work on non-nuclear EMP classified until similar ideas emerged in other nations.

To test the effects of EMP on engineered systems and equipment, an EMP simulator may be used.

Induced pulses are of much lower energy than threat pulses and so are more practicable to create, but they are less predictable. A common test technique is to use a current clamp in reverse, to inject a range of damped sine wave signals into a cable connected to the equipment under test. The damped sine wave generator is able to reproduce the range of induced signals likely to occur.

Sometimes the threat pulse itself is simulated in a repeatable way. The pulse may be reproduced at low energy in order to characterise the subject's response prior to damped sinewave injection, or at high energy to recreate the actual threat conditions. A small-scale ESD simulator may be hand-held. Bench- or room-sized simulators come in a range of designs, depending on the type and level of threat to be generated.

At the top end of the scale, large outdoor test facilities incorporating high-energy EMP simulators have been built by several countries.[17][18] The largest facilities are able to test whole vehicles including ships and aircraft for their susceptibility to EMP. Nearly all of these large EMP simulators used a specialized version of a Marx generator.[17][18] Examples include the huge wooden-structured ATLAS-I simulator (also known as TRESTLE) at Sandia National Labs, New Mexico, which was at one time the world's largest EMP simulator.[19] Papers on this and other large EMP simulators used by the United States during the latter part of the Cold War, along with more general information about electromagnetic pulses, are now in the care of the SUMMA Foundation, which is hosted at the University of New Mexico.[20][21] The US Navy also has a large facility called the Electro Magnetic Pulse Radiation Environmental Simulator for Ships I (EMPRESS I).