Holden Commodore (VS)

Launched in April 1995, the VS Commodore served as a mechanical update of the second generation architecture, destined to assist sales before the all-new VT model in August 1997. The extent of exterior changes veered not much further than a redesigned Holden logo and wheel trims.[2] An updated Ecotec (Emissions and Consumption Optimisation through TEChnology) version of the Buick V6 engine coincided with the changes to the engine in the United States. The Ecotec engine packed 13 percent more power, an increase of 17 kilowatts (23 hp) over the VR, cut fuel consumption by 5 percent, and increased the compression ratio from 9.0:1 to 9.4:1. Holden mated the new engine with a modified version of the GM 4L60-E automatic transmission, bringing improved throttle response and smoother changes between gears.[2] Safety features were also improved, with a passenger airbag becoming available.

The utility version of the VS was released in April 1995. The limited edition VS wagon with manual gearbox had a production run of just 300 vehicles.

The VS Commodore was the last of which to be sold as Toyota Lexcens, as Holden and Toyota ended their model-sharing scheme.[3] The last Lexcens were built during 1997.[4]

In June 1996 the Series II of the VS was launched, featuring the new ECOTEC (Emissions and Consumption Optimisation TEChnology) 3800 V6, which compared to the previous 3800 V6, more powerful, more economic, produces less emissions, quieter and smoother. It was also fitted with a passenger-side airbag, the first Australian built car to offer this feature. Other changes included elliptical side turn signals, interior tweaks and the introduction of a L67 Supercharged V6 engine for selected trim levels.[2] The new supercharged engine slotted in between the existing engines in the lineup and was officially rated at 165 kW (221 hp), just 3 kW (4.0 hp) below the V8.[5]

From 1 January 1997 Holden's new car warranty for the VS Series II and subsequent models increased to 3 years / 100,000 km. Production of the Series II continued until August 1997, when the sedan and wagon were replaced by the new Commodore VT.

As the new VT did not feature a utility variant among its model range, the VS Series II Ute remained in production after the VS sedan and wagon were replaced by the new models. In June 1998 an upgraded version of the Utility, the Series III, was released, which was unique in the Commodore's history as it was limited to just a single variant. The new model Ute was identified by Series III badges and clear side blinker repeater lights, and featured a number of interior upgrades.

The biggest change came in the way of the engine, as the Series II's 165kW V8 was replaced by the new 179kW version from the VT, which featured sequential fuel injection. Along with these changes saw the introduction of the SS V8, the first time this model option was available in a Commodore utility. Externally, the SS was identified by an integrated body kit comprising a new front bumper and side skirts, polished alloy rear sports bar, 16-inch alloy wheels, fog lamps and SS decals. The interior featured a leather wrapped sports steering wheel, hand brake and gearshift knob, and the seats had SS identification. Power windows and air-conditioning was standard, as were the Getrag 5-speed manual transmission, limited-slip differential, sports suspension and ABS brakes.[6]

The Series III Ute remained in production until the December 2000 release of the new Holden Ute (VU).

Between 1995 and 1997 the VS was also sold in small numbers to Malaysia and Singapore as the Opel Calais.[7][8] Prior to the VS, the Opel-badged models were sold in VR specification from 1994. As of December 1994, Holden were selling approximately 40 per month of the VR series Opel Calais.[9] Both the VR and VS versions were fitted with the Opel-sourced 2.6-litre C26NE inline-six engine and four-speed 4L30-E automatic. These vehicles initially featured the front-end of the VR Statesman[9] until a circa 1997 facelift progressed to the front-end design of the VS Caprice. The final batch of Singapore-bound Opel Calais models were produced in August 1997 and featured the newer 2.5-litre X25XE V6 engine with the 4L30-E automatic transmission. However, this order was cancelled, likely due to the imminent Asian financial crisis. As the vehicles were not compliant for sale in Australia, they were instead exported to New Zealand and retailed through Ebbett Waikato dealerships, complied as 1998 models, and rebranded as the Holden Commodore Royale.[10] Some cars were also exported in small numbers to other markets (eg Brunei) but with specifications more similar to those of the Australia market ones.

• 
  Holden Commodore Acclaim sedan (Series II)
• 
  Holden Commodore Executive wagon (Series II)
• 
  Holden Berlina sedan (Series II)
• 
  Holden Calais (Series II)
• 
  Holden Commodore SS
• 
  Holden Commodore Royale (New Zealand; Series II)

• 
  Holden Commodore S utility (Series II)
• 
  Holden Commodore S utility (Series II)

Holden's performance vehicle partner Holden Special Vehicles produced the following range of Holden VS based models, which were each marketed under the HSV brand.

The United Australian Automobile Industries (UAAI) joint venture agreement with Toyota Australia first starting with the VN Commodore continued up to the VS. The VS Lexcen equivalent was known as the T4 series, updated in 1996 to T5 following Commodore’s Series II update. The Lexcen featured subtle styling differences, particularly, the front panels. The Lexcen was discontinued in August 1997 and Toyota would not enter the Australian market with another large family car under their own brand. Instead, the Lexus GS S160 was offered which had similar dimensions to the Lexcen and was available with both inline 6 and V8 engines.

• 
  Toyota Lexcen (T4) CSi sedan
• 
  Toyota Lexcen (T4) CSi sedan
• 
  Toyota Lexcen (T4) CSi wagon
• 
  Toyota Lexcen (T5) CSi sedan