RAF 1

The RAF 1 is a British air-cooled, V-8 engine developed for aircraft use during World War I. Based on a French design, it was developed at the Royal Aircraft Factory, and built by six different British companies including Daimler, Rolls-Royce and Wolseley Motors Limited.

RAF 1
RAF 1a at the National Air and Space Museum
Type Piston V8 aero engine
Manufacturer Royal Aircraft Factory
First run 1913
Major applications Royal Aircraft Factory B.E.2
Airco DH.6
Developed from Renault 70/80 hp

Design and development

The RAF 1 was based on the Renault 70/80 hp engine, being intended specifically to replace that engine in the B.E.2c. It featured larger cylinders (3.94 in × 5.5 in (100 mm × 140 mm)) for a total displacement of 540 cubic inches (8.8 L). It was rated at 92 hp (70 kW) at 1,600 rpm. The heads were cast integrally with the cylinders, with the intake and exhaust valves set one above the other in an upside-down F-head configuration.

The engines featured a large diameter lightweight flywheel at the rear, enclosed in a cast housing. Engine oil was picked up from the bottom of the crankcase and slung into a reservoir at the top. From there it was gravity fed, via a gallery high on the right side of the engine block, to the main bearing caps, and then to the connecting rod journals by the centrifugal effect of the turning crankshaft. The main bearings were ball bearings and were splash fed. Engine oil from the gallery was also supplied to the 1 : 2 reduction gearbox at the front. This drove the four-bladed propeller at one half engine speed, and the single camshaft was splined into the rear of the short propeller shaft. This arrangement meant that no mechanical oil pump was needed. Excess engine oil from the flywheel overflowed the reservoir and trickled over the large surface area of the round flywheel cover.

Two passages cast into the cover took air-fuel mixture from the carburettor mounted at the bottom to a copper U-shaped inlet manifold mounted between the banks of cylinders, and the flywheel cover acted as a heat exchanger, preheating the fuel-air mixture. In late 1915, the bore was increased to 4.1 inches (100 mm), leading to an increased displacement of 590 cubic inches (9.7 L) and power of 86 kW (115 hp) at 1,800 rpm.[1]

Supercharger

In late 1915 a supercharged experimental version of the RAF 1a was developed, the engine being flown in a B.E.2c improving the climb from taking 36 minutes to reach 8,500 ft without the supercharger, to reaching 11,500 ft in the same time.

Variants

RAF 1
RAF 1a
Standard engine for aircraft using this powerplant.
RAF 1b
Uprated version slated for installation in the B.E.2e - reliability problems precluded production.[2]
RAF 1c
RAF 1e

Applications

List from Lumsden [1]

Specifications (RAF 1a)

Data from Lumsden [1]

General characteristics

Components

  • Fuel system: Twin Claudel-Hobson carburettors
  • Cooling system: Air-cooled
  • Reduction gear: 0.5:1, Left-hand tractor

Performance

See also

Related development

Comparable engines

Related lists

References

Notes

  1. Lumsden 2003, p. 223.
  2. Hare (1990) p. 115

Bibliography

  • Gunston, Bill (1986). World Encyclopedia of Aero Engines. Wellingborough: Patrick Stephens. p. 151.
  • Hare, Paul R. The Royal Aircraft Factory. London: Putnam, 1990. ISBN 0-85177-843-7
  • Lumsden, Alec. British Piston Engines and their Aircraft. Marlborough, Wiltshire: Airlife Publishing, 2003. ISBN 1-85310-294-6.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.