Rapp Rp III

The engine had its cylinders arranged in pairs, with two separate steel cylinder liners screwed into the pairwise cast cylinder heads. The cylinder heads had integral cooling jackets and were cast from steel in pairs and then machined.[7][8] The valve seats, with the exhaust valve seats being water-cooled, were separately built parts which were screwed into the cylinder heads and could be easily removed for maintenance work. Both inlet valves of the cylinder pair, and likewise so both exhaust valves on the other side, were pressed into their seat by a single pivoted leaf spring each. The exhaust and inlet valves were actuated successively from a single cam on the overhead camshaft via roller tappets and rocker arms.[8]

First model of the Rapp 150 hp six-cylinder engine, carburettors on the rear end

The camshaft was driven via a vertical timing shaft and bevel gears between the last two cylinder pairs. Two magnetos provided sparks for the two spark plugs per cylinder and likewise were located between the last two cylinder pairs, also driven from the vertical timing shaft. This arrangement had already been used on Karl Rapp's earlier four-cylinder engine, but contrary to the four-cylinder design, on the six-cylinder engine the additional spacing between the last two cylinder pairs led to an asymmetry in the crankshaft and cylinder arrangement. This asymmetry is believed to have been the major contributor to the severe vibration and longevity problems that the engine had been plagued with.

It appears that this position of the vertical timing shaft had been chosen deliberately in order to keep the pairwise cylinder design while at the same time positioning the magnetos away from the rear end of the engine, complying army administration considerations for avoiding interference on the compass.[9][8][7]

The engine case was cast from aluminum in two pieces, parted at the center line in an upper and a lower part. The crankshaft was supported after every two cylinders by the four main journals in the upper part of the crankcase.[10] Lubrication was done by a gear pump which was mounted on the lowest point of the engine. The gear pump fed the oil from a heat permeable cylindrical brass oil reservoir below the engine crankcase to the main journals of the crankshaft, from where it passed on to the rod journals and gudgeon pins through drilled ducts.[9] The proper oil level in the oil reservoir was maintained by an eccentric pump through augmentation of fresh oil and an additional eccentric pump removed excessive oil from the crankcase in case of an inclined engine position.[9][8][10] A gear water pump for circulating the engine coolant was also located below the crankcase.[10]

The first engines had two Zenith-type[10] carburettors located at the rear end of the cylinder row, from where they fed the cylinders via two separate pipes, which were conjoined approximately at cylinder three. On later models this arrangement had been given up and the two Zenith carburettors were the relocated to the more conventional position on the left side of the cylinder block, with each of them feeding three cylinders. An in-flight adjustable amount of pre-heated air could be provided to the carburettors via admission pipes routed through the exhaust.

While the Prussian Army Administration rejected the first delivery of these engines as unsuitable, the Bavarian Army Administration and the German Imperial Navy administration continued to order Rapp engines in limited amounts.[1] Also the Austro-Hungarian Armed Forces and especially the Austro-Hungarian Navy administration, being in dire need for engines for their flying boats, ordered Rapp engines.[1] Engine troubles however prevented a greater success of the engine, with the most severe problems being engine roughness and vibrations, frequently damaged bearings and problems with the carburetion.[1]

In response to a commission for 40 Rapp Rp III engines from the German military authorities, for which the military authorities demanded a power output of at least 175 hp at the acceptance test,[1] Karl Rapp increased the output of his engine accordingly, with further strengthening of the engine resulting in additional weight and increasing vibration problems. It appears that some authors refer to this engine as 175 hp (130 kW) Rapp Rp IIIa,[11] while others still refer to it as Rapp Rp III.[6][12]

The acceptance test in January 1916 turned out to be a failure, with the engines crankshaft breaking after several test runs with a total duration of 32 hours.[1] As a result, also the Bavarian Army Administration a well as the Austrian Army Administration withdrew from ordering further Rapp engines, with the Austro-Hungarian Navy administration remaining the only customer.[1]

• Type: six-cylinder, water-cooled in-line piston engine
• Bore: 140 mm (5.51 in)
• Stroke: 160 mm (6.30 in)
• Displacement: 14.78 L (902 cu in)
• Designer: Karl Rapp

• Valvetrain: two single overhead camshaft-actuated valves per cylinder
• Cooling system: Water-cooled
• Reduction gear: Direct-drive

• Power output: 174 hp (130 kW) at 1,382 rpm
• Compression ratio: 4.65

• Angle, Glenn Dale (1921). Airplane Engine Encyclopedia: An Alphabetically Arranged Compilation Of All Available Data On The World's Airplane Engines. Otterbein Press. pp. 402-404. OL 23525261M.

• Pletschacher, Peter (1992). Die Königlich Bayerischen Fliegertruppen 1912-1919 (in German) (2 ed.). Planegg: Aviatic Verlag. ISBN 3-925505-20-2.

• Huth, Fritz (1914). Motoren für Flugzeuge und Luftschiffe (in German). Berlin: R. C. Schmidt & co. OCLC 11492610.

• Huth, Fritz (1920). Motoren für Flugzeuge und Luftschiffe. Bibliothek für Luftschiffahrt und Flugtechnik,Bd. 14 (in German) (3rd ed.). Berlin: R. C. Schmidt & co. OCLC 2116726.

• Vogelsang, C. Walther (1918). Der Flugmotor und seine Bestandteile. Volckmann's Bibliothek fur Flugwesen,Bd. 2 (in German) (3rd ed.). Berlin-Charlottenburg: C. J. E. Volckmann Nachf. G.m.b.H. OCLC 62113315.

• "Der 150 PS Rapp-Flugmotor". Flugsport (in German). Frankfurt am Main: Redaktion und Verlag Flugsport. Jahrgang 1914 (13): 543–545. June 24, 1914.

• Schwager, Otto (1918). Motorenkunde für Flugzeugführer, Beobachter und Werkmeister, Teil II (in German). Berlin-Charlottenburg: C. J. E. Volckmann Nachf. G.m.b.H. OCLC 49459610.

• Eyb, Robert (1918). Fliegerhandbuch. Bibliothek fur Luftschiffahrt und Flugtechnik ;Bd. 13 (in German) (3rd ed.). Berlin: R.C. Schmidt & Co. OCLC 9500053.

• Schuster, Paul (17 July 1917). "Entwicklung und Stand des Flugzeugwesens". Glasers Annalen (in German). Berlin: F.C. Glaser. 81 (2): 14–19.

• Klamroth, Gerhard (1916). Schiffsmaschinenkunde mit besonderer Berücksichtigung der Dampfturbinen und Ölmotoren (in German). Berlin: E.S. Mittler und Sohn.

• Grosz, P M (2000). Rumpler C.I. Albatros Productions. ISBN 1-902207-21-1.

• Grosz, P M (1996). Albatros C.I. Albatros Productions. ISBN 0-948414-76-6.

• von Gersdorff, Kyrill; Grasmann, Kurt (1981). Flugmotoren und Strahltriebwerke (in German). München: Bernard & Graefe Verlag. ISBN 3-7637-5272-2.

• Ciglić, Boris (2014). Seaplanes of Bocche. Beograd: Jeroplan Books. ISBN 978-86-909727-1-5.

• Herris, Jack (2017). DFW Aircraft of WWI. Aeronaut Books. ISBN 978-1-935881-54-4.

• "Der neue Otto-Doppeldecker". Flugsport (in German). Frankfurt am Main: Redaktion und Verlag Flugsport. Jahrgang 1914 (16): 688–689. August 5, 1914.

• "A new Otto biplane". Flight. London: 248. April 9, 1915.