Optical fiber connector

Optical fiber connectors are used to join optical fibers where a connect/disconnect capability is required. Due to the polishing and tuning procedures that may be incorporated into optical connector manufacturing, connectors are often assembled onto optical fiber in a supplier's manufacturing facility. However, the assembly and polishing operations involved can be performed in the field, for example, to terminate long runs at a patch panel.

Optical fiber connectors are used in telephone exchanges, for customer premises wiring, and in outside plant applications to connect equipment and fiber-optic cables, or to cross-connect cables.

Most optical fiber connectors are spring-loaded, so the fiber faces are pressed together when the connectors are mated. The resulting glass-to-glass or plastic-to-plastic contact eliminates signal losses that would be caused by an air gap between the joined fibers.

Performance of optical fiber connectors can be quantified by insertion loss and return loss. Measurements of these parameters are now defined in IEC standard 61753-1. The standard gives five grades for insertion loss from A (best) to D (worst), and M for multimode. The other parameter is return loss, with grades from 1 (best) to 5 (worst).

A variety of optical fiber connectors are available, but SC and LC connectors are the most common types of connectors on the market.[2] Typical connectors are rated for 500–1,000 mating cycles.[3] The main differences among types of connectors are dimensions and methods of mechanical coupling. Generally, organizations will standardize on one kind of connector, depending on what equipment they commonly use.

In many data center applications, small (e.g., LC) and multi-fiber (e.g., MTP/MPO) connectors have replaced larger, older styles (e.g., SC), allowing more fiber ports per unit of rack space.[4]

Outside plant applications may require connectors be located underground, or on outdoor walls or utility poles. In such settings, protective enclosures are often used, and fall into two broad categories: hermetic (sealed) and free-breathing. Hermetic cases prevent entry of moisture and air but, lacking ventilation, can become hot if exposed to sunlight or other sources of heat. Free-breathing enclosures, on the other hand, allow ventilation, but can also admit moisture, insects and airborne contaminants. Selection of the correct housing depends on the cable and connector type, the location, and environmental factors.

Many types of optical connector have been developed at different times, and for different purposes. Many of them are summarized in the tables below.

Fiber connector types

Short name	Long name	Coupling type	Screw thread	Ferrule diameter	Standard	Applications and notes	Image
Avio (Avim)	Aviation Intermediate Maintenance	Screw				Aerospace and avionics
ADT-UNI		Screw		2.5 mm		Measurement equipment
CS	Corning/Senko	Latch, push-pull	—	1.25 mm		Listed in SFF-8024[5]
DMI	Diamond Micro Interface[6]	Latch, separate	—	2.5 mm		Printed circuit boards
LSH or E-2000 [7]		Latch, push-pull, integral dust cap	—	2.5 mm	IEC 61754-15	Telecom, DWDM systems
EC CF08		Latch, push-pull	—		IEC 1754-8[8]	Telecom and CATV networks
ELIO		Bayonet	—	2.5 mm	ABS1379	PC or UPC
ESCON	Enterprise Systems Connection	Latch, integral shroud[1]	—	2.5 mm		IBM mainframe computers and peripherals
F07				2.5 mm	Japanese Industrial Standard (JIS)	LAN, audio systems; for 200 μm fibers, simple field termination possible, mates with ST connectors
F-3000		Latch, integral light- and dust-cap	—	1.25 mm	IEC 61754-20	Fiber To The Home (LC compatible)
FC	Ferrule Connector or Fiber Channel[9]	Screw	M8×0.75[10]	2.5 mm	IEC 61754-13[8]	Datacom, telecom, measurement equipment, single-mode lasers[11] [upper-alpha 1][upper-alpha 2]
Fibergate		Latch, integral dust-cap	—	1.25 mm		Backplane connector
FJ	Fiber-Jack[13] or Opti-Jack[9]	Latch[1]	—	2.5 mm		Building wiring, wall outlets
LC	Lucent Connector,[9] Little Connector,[14] or Local Connector[14]	Latch	—	1.25 mm	IEC 61754-20[8]	High-density connections, SFP and SFP+ transceivers, XFP transceivers.[11] Duplex LC is comparable in size to RJ-45. [upper-alpha 3]
Luxcis				1.25 mm	ARINC 801	PC (straight physical contact) or APC (angled physical contact) configurations
LX-5		Latch, integral light- and dust-cap	—		IEC 61754-23	High-density connections; rarely used
M12-FO		Screw	M16	2.5 mm	EN 61754-27, ISO/IEC 61754-27	Machine, process and plant engineering. IP-67 dust and water resistant
MIC FDDI	Media Interface Connector Fiber distributed data interface	Snap	—	2.5 mm
MPO or MTP	Multiple-fiber Push-On/Pull-off[9]	Snap, push-pull, gendered	—	2.5×6.4 mm[15]	IEC-61754-7;[8] EIA/TIA-604-5 (FOCIS 5)	SM or MM multi-fiber ribbon. Same ferrule as MT, but more easily reconnectable.[15] Used for indoor cabling and device interconnections. MTP is a brand name for an improved connector, which intermates with MPO.[16] [upper-alpha 4]
MT	Mechanical Transfer	Latch, gendered[1]	—	2.5×6.4 mm		Pre-terminated cable assemblies; outdoor applications[15]
MT-RJ	Mechanical Transfer Registered Jack or Media Termination - recommended jack[9]	Latch, gendered[1]	—	2.45×4.4 mm	IEC 61754-18	Duplex multimode connections [upper-alpha 5]
MU	Miniature unit[9]	Latch, push-pull	—	1.25 mm	IEC 61754-6	Common in Japan[1]
SC	Subscriber connector,[9] square connector[9] or standard connector	Latch, push-pull	—	2.5 mm	IEC 61754-4[8]	Datacom and telecom (most widely deployed); GPON; EPON; GBIC; MADI [upper-alpha 6][upper-alpha 3]
SC-DC SC-QC	SC-Dual Contact SC-Quattro Contact[13]	Latch, push-pull	—	2.5 mm	IEC 61754-4	Datacom and telecom; GPON; EPON; GBIC
SMA 905[upper-alpha 7] F-SMA I	Sub Miniature A	Screw, optionally keyed	1/4"-36 UNS 2B	3.17 mm[18]	IEC 60874-2	Industrial lasers, optical spectrometers, military; telecom multimode [upper-alpha 8]
SMA 906 F-SMA II	Sub Miniature A	Screw	1/4"-36 UNS 2B	Stepped; 0.118 to 0.089 in 3.0 to 2.3 mm, typ.	IEC 60874-2	Industrial lasers, military; telecom multimode [upper-alpha 8]
SMC	Sub Miniature C	Snap	—	2.5 mm
ST or BFOC	Straight Tip[upper-alpha 9][9] or Bayonet Fiber Optic Connector	Bayonet	—	2.5 mm	IEC 61754-2[8]	Datacom [upper-alpha 10]
TOSLINK	Toshiba Link	Snap-fit	—		Most commonly, JIS F05	Digital audio
VF-45 SG	Volition Fiber	Latch	—	None, V-grooves as guidance		Datacom
1053 HDTV	Broadcast connector interface	Push-pull coupling	—	1.25 mm ceramic		Audio & data (broadcasting)
V-PIN	V-System	Snap-fit, push-pull	—			Industrial and electric utility networking; multimode 200 μm, 400 μm, 1 mm, 2.2 mm fibers

Features of good connector design:

• Low insertion loss - should not exceed 0.75 dB
• Typical insertion repeatability, the difference in insertion loss between one plugging and another, is 0.2 dB.
• High return loss (low amounts of reflection at the interface) - should be higher than 20 dB
• Ease of installation
• Low cost
• Reliability
• Low environmental sensitivity
• Ease of use

• On all connectors, cleaning the ceramic ferrule before each connection helps prevent scratches and extends the connector life substantially.
• Connectors on polarization-maintaining fiber are sometimes marked with a blue strain relief boot or connector body. Sometimes a blue buffer tube is used on the fiber instead.[23]
• Hardened Fiber Optic Connectors (HFOCs) and Hardened Fiber Optic Adapters (HFOAs) are passive telecommunications components used in an outside plant environment. They provide drop connections to customers from fiber distribution networks. These components may be provided in pedestal closures,[note 1][24] aerial and buried closures and terminals, or equipment located at customer premises such as a Fiber Distribution Hub (FDH) or an optical network terminal unit.

These connectors, which are field-mateable and hardened for use in the OSP, are needed to support Fiber to the Premises (FTTP) deployment and service offerings. HFOCs are designed to withstand climatic conditions existing throughout the U.S., including rain, flooding, snow, sleet, high winds, and ice and sand storms. Ambient temperatures ranging from −40 °C (−40 °F) to 70 °C (158 °F) can be encountered.

Telcordia GR-3120[25] contains the industry’s most recent generic requirements for HFOCs and HFOAs.

Glass fiber optic connector performance is affected both by the connector and by the glass fiber. Concentricity tolerances affect the fiber, fiber core, and connector body. The core optical index of refraction is also subject to variations. Stress in the polished fiber can cause excess return loss. The fiber can slide along its length in the connector. The shape of the connector tip may be incorrectly profiled during polishing. The connector manufacturer has little control over these factors, so in-service performance may well be below the manufacturer's specification.

Testing fiber optic connector assemblies falls into two general categories: factory testing and field testing.

Factory testing is sometimes statistical, for example, a process check. A profiling system may be used to ensure the overall polished shape is correct, and a good quality optical microscope to check for blemishes. Insertion loss and return loss performance is checked using specific reference conditions, against a reference-standard single-mode test lead, or using an encircled flux compliant source for multi-mode testing. Testing and rejection (yield) may represent a significant part of the overall manufacturing cost.

Field testing is usually simpler. A special hand-held optical microscope is used to check for dirt or blemishes. A power meter and light source or an optical loss test set (OLTS) is used to test end-to-end loss, and an optical time-domain reflectometer may be used to identify significant point losses or return losses.

• Gap loss – attenuation sources and causes
• Index-matching material – a liquid/gel to reduce Fresnel reflection
• Mechanical splice – a more permanent, but still mechanical connection
• Optical attenuator – fiber optic attenuator

Wikimedia Commons has media related to Optical fiber connectors.

• Fiber Optic Connector Reference