Cirque

Glacial cirques are found amongst mountain ranges throughout the world; 'classic' cirques are typically about one kilometer long and one kilometer wide. Situated high on a mountainside near the firn line, they are typically partially surrounded on three sides by steep cliffs. The highest cliff often is called a headwall. The fourth side forms the lip, threshold or sill,[3] the side at which the glacier flowed away from the cirque. Many glacial cirques contain tarns dammed by either till (debris) or a bedrock threshold. When enough snow accumulates it can flow out the opening of the bowl and form valley glaciers which may be several kilometers long.

Cirques form in conditions which are favorable; in the northern hemisphere the conditions include the north-east slope where they are protected from the majority of the sun's energy and from the prevailing winds. These areas are sheltered from heat, encouraging the accumulation of snow; if the accumulation of snow increases, the snow turns into glacial ice. The process of nivation follows, whereby a hollow in a slope may be enlarged by ice segregation weathering and glacial erosion. Ice segregation erodes the vertical rock face and causes it to disintegrate, which may result in an avalanche bringing down more snow and rock to add to the growing glacier.[4] Eventually, this hollow may become large enough that glacial erosion intensifies. The enlarging of this open ended concavity creates a larger leeward deposition zone, furthering the process of glaciation. Debris (or till) in the ice also may abrade the bed surface; should ice move down a slope it would have a ‘sandpaper effect’ on the bedrock beneath, on which it scrapes.

The Lower Curtis Glacier in North Cascades National Park is a well-developed cirque glacier; if the glacier continues to retreat and melt away, a lake may form in the basin

Eventually, the hollow may become a large bowl shape in the side of the mountain, with the headwall being weathered by ice segregation, and as well as being eroded by plucking. The basin will become deeper as it continues to be eroded by ice segregation and abrasion.[4][5] Should ice segregation, plucking and abrasion continue, the dimensions of the cirque will increase, but the proportion of the landform would remain roughly the same. A bergschrund forms when the movement of the glacier separates the moving ice from the stationary ice forming a crevasse. The method of erosion of the headwall lying between the surface of the glacier and the cirque's floor has been attributed to freeze-thaw mechanisms. The temperature within the bergschrund changes very little, however, studies have shown that ice segregation (frost shattering) may happen with only small changes in temperature. Water that flows into the bergschrund can be cooled to freezing temperatures by the surrounding ice allowing freeze-thaw mechanisms to occur.

Lake Seal, Mt. Field National Park, Tasmania – a cirque formed from a glacier is visible in the walls around Lake Seal[6]

If two adjacent cirques erode toward one another, an arête, or steep sided ridge, forms. When three or more cirques erode toward one another, a pyramidal peak is created. In some cases, this peak will be made accessible by one or more arêtes. The Matterhorn in the European Alps is an example of such a peak.

Where cirques form one behind the other, a cirque stairway results as at the Zastler Loch in the Black Forest.

As glaciers can only originate above the snowline, studying the location of present-day cirques provides information on past glaciation patterns and on climate change.[7]

The Cirque du Bout du Monde

Although a less common usage,[nb 1] the term cirque is also used for amphitheatre-shaped, fluvial-erosion features. For example, an approximately 200 square kilometres (77 sq mi) anticlinal erosion cirque is at 30°35′N 34°45′E on the southern boundary of the Negev highlands. This erosional cirque or makhtesh was formed by intermittent river flow in the Makhtesh Ramon cutting through layers of limestone and chalk, resulting in cirque walls with a sheer 200 metres (660 ft) drop.[8] The Cirque du Bout du Monde is another such feature, created in karst terraine in the Burgundy region of the department of Côte-d'Or in France.

Yet another type of fluvial erosion-formed cirque is found on Réunion island, which includes the tallest volcanic structure in the Indian Ocean. The island consists of an active shield-volcano (Piton de la Fournaise) and an extinct, deeply eroded volcano (Piton des Neiges). Three cirques have eroded there in a sequence of agglomerated, fragmented rock and volcanic breccia associated with pillow-lavas overlain by more coherent, solid lavas.[9]

A common feature for all fluvial-erosion cirques is a terrain which includes erosion resistant upper structures overlying materials which are more easily eroded.

The Western Cwm with the Lhotse face of Mount Everest in the background