DDR2 SDRAM

PC2-5300 DDR2 SO-DIMM (for notebooks)

Comparison of memory modules for desktop PCs (DIMM)

Comparison of memory modules for portable/mobile PCs (SO-DIMM)

The key difference between DDR2 and DDR SDRAM is the increase in prefetch length. In DDR SDRAM, the prefetch length was two bits for every bit in a word; whereas it is four bits in DDR2 SDRAM. During an access, four bits were read or written to or from a four-bit-deep prefetch queue. This queue received or transmitted its data over the data bus in two data bus clock cycles (each clock cycle transferred two bits of data). Increasing the prefetch length allowed DDR2 SDRAM to double the rate at which data could be transferred over the data bus without a corresponding doubling in the rate at which the DRAM array could be accessed. DDR2 SDRAM was designed with such a scheme to avoid an excessive increase in power consumption.

DDR2's bus frequency is boosted by electrical interface improvements, on-die termination, prefetch buffers and off-chip drivers. However, latency is greatly increased as a trade-off. The DDR2 prefetch buffer is four bits deep, whereas it is two bits deep for DDR. While DDR SDRAM has typical read latencies of between two and three bus cycles, DDR2 may have read latencies between three and nine cycles, although the typical range is between four and six. Thus, DDR2 memory must be operated at twice the data rate to achieve the same latency.

Another cost of the increased bandwidth is the requirement that the chips are packaged in a more expensive and difficult to assemble BGA package as compared to the TSSOP package of the previous memory generations such as DDR SDRAM and SDR SDRAM. This packaging change was necessary to maintain signal integrity at higher bus speeds.

Power savings are achieved primarily due to an improved manufacturing process through die shrinkage, resulting in a drop in operating voltage (1.8 V compared to DDR's 2.5 V). The lower memory clock frequency may also enable power reductions in applications that do not require the highest available data rates.

According to JEDEC[4] the maximum recommended voltage is 1.9 volts and should be considered the absolute maximum when memory stability is an issue (such as in servers or other mission critical devices). In addition, JEDEC states that memory modules must withstand up to 2.3 volts before incurring permanent damage (although they may not actually function correctly at that level).

For use in computers, DDR2 SDRAM is supplied in DIMMs with 240 pins and a single locating notch. Laptop DDR2 SO-DIMMs have 200 pins and often come identified by an additional S in their designation. DIMMs are identified by their peak transfer capacity (often called bandwidth).

* Some manufacturers label their DDR2 modules as PC2-4300, PC2-5400 or PC2-8600 instead of the respective names suggested by JEDEC. At least one manufacturer has reported this reflects successful testing at a higher-than-standard data rate[8] whilst others simply round up for the name.

Note: DDR2-xxx denotes data transfer rate, and describes raw DDR chips, whereas PC2-xxxx denotes theoretical bandwidth (with the last two digits truncated), and is used to describe assembled DIMMs. Bandwidth is calculated by taking transfers per second and multiplying by eight. This is because DDR2 memory modules transfer data on a bus that is 64 data bits wide, and since a byte comprises 8 bits, this equates to 8 bytes of data per transfer.

DDR2 P vs F Server DIMM's Notch Positions compared

In addition to bandwidth and capacity variants, modules can:

1. Optionally implement ECC, which is an extra data byte lane used for correcting minor errors and detecting major errors for better reliability. Modules with ECC are identified by an additional ECC in their designation. PC2-4200 ECC is a PC2-4200 module with ECC. An additional P can be added at the end of the designation, P standing for parity (ex : PC2-5300P).
2. 

   Intel ® 6402 Advanced Memory Buffer
   Be "registered" ("buffered"), which improves signal integrity (and hence potentially clock rates and physical slot capacity) by electrically buffering the signals at a cost of an extra clock of increased latency. Those modules are identified by an additional R in their designation, whereas non-registered (a.k.a. "unbuffered") RAM may be identified by an additional U in the designation. PC2-4200R is a registered PC2-4200 module, PC2-4200R ECC is the same module but with additional ECC.
3. Be aware fully buffered modules, which are designated by F or FB do not have the same notch position as other classes. Fully buffered modules cannot be used with motherboards that are made for registered modules, and the different notch position physically prevents their insertion.

Note:

• Registered and un-buffered SDRAM generally cannot be mixed on the same channel.
• The highest-rated DDR2 modules in 2009 operate at 533 MHz (1066 MT/s), compared to the highest-rated DDR modules operating at 200 MHz (400 MT/s). At the same time, the CAS latency of 11.2 ns = 6 / (bus clock rate) for the best PC2-8500 modules is comparable to that of 10 ns = 4 / (bus clock rate) for the best PC-3200 modules.

DDR2 DIMMs are not backward compatible with DDR DIMMs. The notch on DDR2 DIMMs is in a different position from DDR DIMMs, and the pin density is higher than DDR DIMMs in desktops. DDR2 is a 240-pin module, DDR is a 184-pin module. Notebooks have 200-pin SO-DIMMs for DDR and DDR2; however, the notch on DDR2 modules is in a slightly different position than on DDR modules.

Higher-speed DDR2 DIMMs can be mixed with lower-speed DDR2 DIMMs, although the memory controller will operate all DIMMs at same speed as the lowest-speed DIMM present.