Internet Control Message Protocol

The Internet Control Message Protocol (ICMP) is a supporting protocol in the Internet protocol suite. It is used by network devices, including routers, to send error messages and operational information indicating success or failure when communicating with another IP address, for example, an error is indicated when a requested service is not available or that a host or router could not be reached.[2] ICMP differs from transport protocols such as TCP and UDP in that it is not typically used to exchange data between systems, nor is it regularly employed by end-user network applications (with the exception of some diagnostic tools like ping and traceroute).

Internet Control Message Protocol
Communication protocol
A general header for ICMPv4
PurposeAuxiliary protocol for IPv4[1]
Developer(s)DARPA
Introduction1981
OSI layerNetwork layer
RFC(s)RFC 792

ICMP for IPv4 is defined in RFC 792. A separate ICMPv6, defined by RFC 4443, is used with IPv6.

Technical details

ICMP is part of the Internet protocol suite as defined in RFC 792. ICMP messages are typically used for diagnostic or control purposes or generated in response to errors in IP operations (as specified in RFC 1122). ICMP errors are directed to the source IP address of the originating packet.[2]

For example, every device (such as an intermediate router) forwarding an IP datagram first decrements the time to live (TTL) field in the IP header by one. If the resulting TTL is 0, the packet is discarded and an ICMP time exceeded in transit message is sent to the datagram's source address.

Many commonly used network utilities are based on ICMP messages. The traceroute command can be implemented by transmitting IP datagrams with specially set IP TTL header fields, and looking for ICMP time exceeded in transit and Destination unreachable messages generated in response. The related ping utility is implemented using the ICMP echo request and echo reply messages.

ICMP uses the basic support of IP as if it were a higher-level protocol, however, ICMP is actually an integral part of IP. Although ICMP messages are contained within standard IP packets, ICMP messages are usually processed as a special case, distinguished from normal IP processing. In many cases, it is necessary to inspect the contents of the ICMP message and deliver the appropriate error message to the application responsible for transmitting the IP packet that prompted the ICMP message to be sent.

ICMP is a network-layer protocol. There is no TCP or UDP port number associated with ICMP packets as these numbers are associated with the transport layer above.[3]

Datagram structure

The ICMP packet is encapsulated in an IPv4 packet.[2] The packet consists of header and data sections.

The ICMP header starts after the IPv4 header and is identified by IP protocol number '1'.[4] All ICMP packets have an 8-byte header and variable-sized data section. The first 4 bytes of the header have fixed format, while the last 4 bytes depend on the type/code of that ICMP packet.[2]

ICMP header format
Offsets Octet 0 1 2 3
Octet Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
0 0 Type Code Checksum
4 32 Rest of header
Type
ICMP type, see § Control messages.
Code
ICMP subtype, see § Control messages.
Checksum
Internet checksum (RFC 1071) for error checking, calculated from the ICMP header and data with value 0 substituted for this field.
Rest of header
Four-byte field, contents vary based on the ICMP type and code.

Data

ICMP error messages contain a data section that includes a copy of the entire IPv4 header, plus at least the first eight bytes of data from the IPv4 packet that caused the error message. The length of ICMP error messages should not exceed 576 bytes.[5] This data is used by the host to match the message to the appropriate process. If a higher level protocol uses port numbers, they are assumed to be in the first eight bytes of the original datagram's data.[6]

The variable size of the ICMP packet data section has been exploited. In the "Ping of death", large or fragmented ICMP packets are used for denial-of-service attacks. ICMP data can also be used to create covert channels for communication. These channels are known as ICMP tunnels.

Control messages

Control messages are identified by the value in the type field. The code field gives additional context information for the message. Some control messages have been deprecated since the protocol was first introduced.

Notable control messages[7][8]
TypeCodeStatusDescription
0 – Echo Reply[6]:14 0Echo reply (used to ping)
1 and 2 unassignedReserved
3 – Destination Unreachable[6]:4 0Destination network unreachable
1Destination host unreachable
2Destination protocol unreachable
3Destination port unreachable
4Fragmentation required, and DF flag set
5Source route failed
6Destination network unknown
7Destination host unknown
8Source host isolated
9Network administratively prohibited
10Host administratively prohibited
11Network unreachable for ToS
12Host unreachable for ToS
13Communication administratively prohibited
14Host Precedence Violation
15Precedence cutoff in effect
4 – Source Quench 0deprecatedSource quench (congestion control)
5 – Redirect Message 0Redirect Datagram for the Network
1Redirect Datagram for the Host
2Redirect Datagram for the ToS & network
3Redirect Datagram for the ToS & host
6deprecatedAlternate Host Address
7unassignedReserved
8 – Echo Request 0Echo request (used to ping)
9 – Router Advertisement 0Router Advertisement
10 – Router Solicitation 0Router discovery/selection/solicitation
11 – Time Exceeded[6]:6 0TTL expired in transit
1Fragment reassembly time exceeded
12 – Parameter Problem: Bad IP header 0Pointer indicates the error
1Missing a required option
2Bad length
13 – Timestamp 0Timestamp
14 – Timestamp Reply 0Timestamp reply
15 – Information Request 0deprecatedInformation Request
16 – Information Reply 0deprecatedInformation Reply
17 – Address Mask Request 0deprecatedAddress Mask Request
18 – Address Mask Reply 0deprecatedAddress Mask Reply
19reservedReserved for security
20 through 29reservedReserved for robustness experiment
30 – Traceroute 0deprecatedInformation Request
31deprecatedDatagram Conversion Error
32deprecatedMobile Host Redirect
33deprecatedWhere-Are-You (originally meant for IPv6)
34deprecatedHere-I-Am (originally meant for IPv6)
35deprecatedMobile Registration Request
36deprecatedMobile Registration Reply
37deprecatedDomain Name Request
38deprecatedDomain Name Reply
39deprecatedSKIP Algorithm Discovery Protocol, Simple Key-Management for Internet Protocol
40Photuris, Security failures
41ExperimentalICMP for experimental mobility protocols such as Seamoby [RFC4065]
42 – Extended Echo Request[9] 0Request Extended Echo (XPing - see Extended Ping (Xping))
43 – Extended Echo Reply[9] 0No Error
1Malformed Query
2No Such Interface
3No Such Table Entry
4Multiple Interfaces Satisfy Query
44 through 252unassignedReserved
253ExperimentalRFC3692-style Experiment 1 (RFC 4727)
254ExperimentalRFC3692-style Experiment 2 (RFC 4727)
255reservedReserved

Source quench

Source Quench requests that the sender decrease the rate of messages sent to a router or host. This message may be generated if a router or host does not have sufficient buffer space to process the request, or may occur if the router or host buffer is approaching its limit.

Data is sent at a very high speed from a host or from several hosts at the same time to a particular router on a network. Although a router has buffering capabilities, the buffering is limited to within a specified range. The router cannot queue any more data than the capacity of the limited buffering space. Thus if the queue gets filled up, incoming data is discarded until the queue is no longer full. But as no acknowledgement mechanism is present in the network layer, the client does not know whether the data has reached the destination successfully. Hence some remedial measures should be taken by the network layer to avoid these kind of situations. These measures are referred to as source quench. In a source quench mechanism, the router sees that the incoming data rate is much faster than the outgoing data rate, and sends an ICMP message to the clients, informing them that they should slow down their data transfer speeds or wait for a certain amount of time before attempting to send more data. When a client receives this message, it will automatically slow down the outgoing data rate or wait for a sufficient amount of time, which enables the router to empty the queue. Thus the source quench ICMP message acts as flow control in the network layer.

Since research suggested that "ICMP Source Quench [was] an ineffective (and unfair) antidote for congestion",[10] routers' creation of source quench messages was deprecated in 1995 by RFC 1812. Furthermore, forwarding of and any kind of reaction to (flow control actions) source quench messages was deprecated from 2012 by RFC 6633.

Source quench message[6]:9
0001020304050607 0809101112131415 1617181920212223 2425262728293031
Type = 4 Code = 0 Checksum
unused
IP header and first 8 bytes of original datagram's data

Where:

Type must be set to 4
Code must be set to 0
IP header and additional data is used by the sender to match the reply with the associated request

Redirect

An example of how an ICMPv4 redirect message works

Redirect requests data packets be sent on an alternative route. ICMP Redirect is a mechanism for routers to convey routing information to hosts. The message informs a host to update its routing information (to send packets on an alternative route). If a host tries to send data through a router (R1) and R1 sends the data on another router (R2) and a direct path from the host to R2 is available (that is, the host and R2 are on the same subnetwork), then R1 will send a redirect message to inform the host that the best route for the destination is via R2. The host should then change its route information and send packets for that destination directly to R2. The router will still send the original datagram to the intended destination.[11] However, if the datagram contains routing information, this message will not be sent even if a better route is available. RFC 1122 states that redirects should only be sent by gateways and should not be sent by Internet hosts.

Redirect message[6]:11
0001020304050607 0809101112131415 1617181920212223 2425262728293031
Type = 5 Code Checksum
IP address
IP header and first 8 bytes of original datagram's data

Where:

Type must be set to 5.
Code specifies the reason for the redirection, and may be one of the following:
Code Description
0 Redirect for Network
1 Redirect for Host
2 Redirect for Type of Service and Network
3 Redirect for Type of Service and Host
IP address is the 32-bit address of the gateway to which the redirection should be sent.
IP header and additional data is included to allow the host to match the reply with the request that caused the redirection reply.

Time exceeded

Time Exceeded is generated by a gateway to inform the source of a discarded datagram due to the time to live field reaching zero. A time exceeded message may also be sent by a host if it fails to reassemble a fragmented datagram within its time limit.

Time exceeded messages are used by the traceroute utility to identify gateways on the path between two hosts.

Time exceeded message[6]:5
0001020304050607 0809101112131415 1617181920212223 2425262728293031
Type = 11 Code Checksum
unused
IP header and first 8 bytes of original datagram's data

Where:

Type must be set to 11
Code specifies the reason for the time exceeded message, include the following:
CodeDescription
0 Time-to-live exceeded in transit.
1 Fragment reassembly time exceeded.
IP header and first 64 bits of the original payload are used by the source host to match the time exceeded message to the discarded datagram. For higher-level protocols such as UDP and TCP the 64-bit payload will include the source and destination ports of the discarded packet.

Timestamp

Timestamp is used for time synchronization. The originating timestamp is set to the time (in milliseconds since midnight) the sender last touched the packet. The receive and transmit timestamps are not used.

Timestamp message[6]:15
0001020304050607 0809101112131415 1617181920212223 2425262728293031
Type = 13 Code = 0 Checksum
Identifier Sequence number
Originate timestamp
Receive timestamp
Transmit timestamp

Where:

Type must be set to 13
Code must be set to 0
Identifier and Sequence Number can be used by the client to match the timestamp reply with the timestamp request.
Originate timestamp is the number of milliseconds since midnight Universal Time (UT). If a UT reference is not available the most-significant bit can be set to indicate a non-standard time value.

Timestamp reply

Timestamp Reply replies to a Timestamp message. It consists of the originating timestamp sent by the sender of the Timestamp as well as a receive timestamp indicating when the Timestamp was received and a transmit timestamp indicating when the Timestamp reply was sent.

Timestamp reply message[6]:15
0001020304050607 0809101112131415 1617181920212223 2425262728293031
Type = 14 Code = 0 Checksum
Identifier Sequence number
Originate timestamp
Receive timestamp
Transmit timestamp

Where:

Type must be set to 14
Code must be set to 0
Identifier and Sequence number can be used by the client to match the reply with the request that caused the reply.
Originate timestamp is the time the sender last touched the message before sending it.
Receive timestamp is the time the echoer first touched it on receipt.
Transmit timestamp is the time the echoer last touched the message on sending it.
All timestamps are in units of milliseconds since midnight UT. If the time is not available in milliseconds or cannot be provided with respect to midnight UT then any time can be inserted in a timestamp provided the high order bit of the timestamp is also set to indicate this non-standard value.

The use of Timestamp and Timestamp Reply messages to synchronize the clocks of Internet nodes has largely been replaced by the UDP-based Network Time Protocol and the Precision Time Protocol.[12]

Address mask request

Address mask request is normally sent by a host to a router in order to obtain an appropriate subnet mask.

Recipients should reply to this message with an Address mask reply message.

Address mask request
0001020304050607 0809101112131415 1617181920212223 2425262728293031
Type = 17 Code = 0 Checksum
Identifier Sequence number
Address mask

Where:

Type must be set to 17
Code must be set to 0
Address mask can be set to 0

ICMP Address Mask Request may be used as a part of reconnaissance attack to gather information on the target network, therefore ICMP Address Mask Reply is disabled by default on Cisco IOS.[13]

Address mask reply

Address mask reply is used to reply to an address mask request message with an appropriate subnet mask.

Address mask reply
0001020304050607 0809101112131415 1617181920212223 2425262728293031
Type = 18 Code = 0 Checksum
Identifier Sequence number
Address mask

Where:

Type must be set to 18
Code must be set to 0
Address mask should be set to the subnet mask

Destination unreachable

Destination unreachable is generated by the host or its inbound gateway[6] to inform the client that the destination is unreachable for some reason. Reasons for this message may include: the physical connection to the host does not exist (distance is infinite); the indicated protocol or port is not active; the data must be fragmented but the 'don't fragment' flag is on. Unreachable TCP ports notably respond with TCP RST rather than a destination unreachable type 3 as might be expected. Destination unreachable is never reported for IP multicast transmissions.

Destination unreachable message[6]:3
0001020304050607 0809101112131415 1617181920212223 2425262728293031
Type = 3 Code Checksum
unused Next-hop MTU
IP header and first 8 bytes of original datagram's data

Where:

Type field (bits 0–7) must be set to 3
Code field (bits 8–15) is used to specify the type of error, and can be any of the following:
CodeDescription
0 Network unreachable error.
1 Host unreachable error.
2 Protocol unreachable error (the designated transport protocol is not supported).
3 Port unreachable error (the designated protocol is unable to inform the host of the incoming message).
4 The datagram is too big. Packet fragmentation is required but the 'don't fragment' (DF) flag is on.
5 Source route failed error.
6 Destination network unknown error.
7 Destination host unknown error.
8 Source host isolated error.
9 The destination network is administratively prohibited.
10 The destination host is administratively prohibited.
11 The network is unreachable for Type Of Service.
12 The host is unreachable for Type Of Service.
13 Communication administratively prohibited (administrative filtering prevents packet from being forwarded).
14 Host precedence violation (indicates the requested precedence is not permitted for the combination of host or network and port).
15 Precedence cutoff in effect (precedence of datagram is below the level set by the network administrators).
Next-hop MTU field (bits 48–63) contains the MTU of the next-hop network if a code 4 error occurs.[14]
IP header and additional data is included to allow the client to match the reply with the request that caused the destination unreachable reply.

See also

  • ICMP tunnel
  • ICMP hole punching
  • ICMP Router Discovery Protocol
  • Pathping
  • Path MTU Discovery
  • Smurf attack

References

  1. F. Baker (June 1995). Baker, F (ed.). Requirements for IP Version 4 Routers. p. 52. RFC 1812.
  2. Forouzan, Behrouz A. (2007). Data Communications And Networking (Fourth ed.). Boston: McGraw-Hill. pp. 621–630. ISBN 978-0-07-296775-3.
  3. "The OSI Model's Seven Layers Defined and Functions Explained". Microsoft Support. Retrieved 2014-12-28.
  4. "Protocol Numbers". Internet Assigned Numbers Authority. Retrieved 2011-06-23.
  5. Requirements for IP Version 4 Routers. doi:10.17487/RFC1812. RFC 1812.
  6. Postel, J. (September 1981). Internet Control Message Protocol. IETF. doi:10.17487/RFC0792. RFC 792.
  7. "IANA ICMP Parameters". Iana.org. 2012-09-21. Retrieved 2013-01-07.
  8. Kurose, J.F; Ross, K.W. (2006). Computer Networking: A Top-Down Approach. World student series. Addison-Wesley. ISBN 9780321418494.
  9. PROBE: A Utility for Probing Interfaces. doi:10.17487/RFC8335. RFC 8335.
  10. RFC 6633
  11. "When Are ICMP Redirects Sent?". Cisco Systems. 2008-06-28. Retrieved 2013-08-15.
  12. D.L. Mills (September 1985). Network Time Protocol (NTP). doi:10.17487/RFC0958. RFC 958. It is evolved from the Time Protocol and the ICMP Timestamp message and is a suitable replacement for both.
  13. "Cisco IOS IP Command Reference, Volume 1 of 4: Addressing and Services, Release 12.3 - IP Addressing and Services Commands: ip mask-reply through ip web-cache". Cisco Systems. Archived from the original on 2013-01-02. Retrieved 2013-01-07.
  14. Extended ICMP to Support Multi-Part Messages. doi:10.17487/RFC4884. RFC 4884.

Sources

RFCs

  • RFC 792, Internet Control Message Protocol
  • RFC 950, Internet Standard Subnetting Procedure
  • RFC 1016, Something a Host Could Do with Source Quench: The Source Quench Introduced Delay (SQuID)
  • RFC 1122, Requirements for Internet Hosts – Communication Layers
  • RFC 1716, Towards Requirements for IP Routers
  • RFC 1812, Requirements for IP Version 4 Routers
  • RFC 4884, Extended ICMP to Support Multi-Part Messages
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.