Microcode

The lowest layer in a computer's software stack is traditionally raw machine code instructions for the processor. In microcoded processors, fetching and decoding those instructions, and executing them, may be done by microcode. To avoid confusion, each microprogram-related element is differentiated by the micro prefix: microinstruction, microassembler, microprogrammer, microarchitecture, etc.

Complex digital processors may also employ more than one (possibly microcode-based) control unit in order to delegate sub-tasks that must be performed essentially asynchronously in parallel. For example, the VAX 9000 has a IBox unit to fetch and decode instructions, which it hands to a microcoded EBox unit to be executed,[5] and the VAX 8800 has both a microcoded IBox and a microcoded EBox.[6]

A high-level programmer, or even an assembly language programmer, does not normally see or change microcode. Unlike machine code, which often retains some backward compatibility among different processors in a family, microcode only runs on the exact electronic circuitry for which it is designed, as it constitutes an inherent part of the particular processor design itself.

Microcode was originally developed as a simpler method of developing the control logic for a computer. Initially, CPU instruction sets were hardwired. Each step needed to fetch, decode, and execute the machine instructions (including any operand address calculations, reads, and writes) was controlled directly by combinational logic and rather minimal sequential state machine circuitry. While such hard-wired processors were very efficient, the need for powerful instruction sets with multi-step addressing and complex operations (see below) made them difficult to design and debug; highly encoded and varied-length instructions can contribute to this as well, especially when very irregular encodings are used.

Microcode simplified the job by allowing much of the processor's behaviour and programming model to be defined via microprogram routines rather than by dedicated circuitry. Even late in the design process, microcode could easily be changed, whereas hard-wired CPU designs were very cumbersome to change. Thus, this greatly facilitated CPU design.

From the 1940s to the late 1970s, a large portion of programming was done in assembly language; higher-level instructions mean greater programmer productivity, so an important advantage of microcode was the relative ease by which powerful machine instructions can be defined. The ultimate extension of this are "Directly Executable High Level Language" designs, in which each statement of a high-level language such as PL/I is entirely and directly executed by microcode, without compilation. The IBM Future Systems project and Data General Fountainhead Processor are examples of this. During the 1970s, CPU speeds grew more quickly than memory speeds and numerous techniques such as memory block transfer, memory pre-fetch and multi-level caches were used to alleviate this. High-level machine instructions, made possible by microcode, helped further, as fewer more complex machine instructions require less memory bandwidth. For example, an operation on a character string can be done as a single machine instruction, thus avoiding multiple instruction fetches.

Architectures with instruction sets implemented by complex microprograms included the IBM System/360 and Digital Equipment Corporation VAX. The approach of increasingly complex microcode-implemented instruction sets was later called complex instruction set computer (CISC). An alternate approach, used in many microprocessors, is to use one or more programmable logic array (PLA) or read-only memory (ROM) (instead of combinational logic) mainly for instruction decoding, and let a simple state machine (without much, or any, microcode) do most of the sequencing. The MOS Technology 6502 is an example of a microprocessor using a PLA for instruction decode and sequencing. The PLA is visible in photomicrographs of the chip,[9] and its operation can be seen in the transistor-level simulation.

Microprogramming is still used in modern CPU designs. In some cases, after the microcode is debugged in simulation, logic functions are substituted for the control store. Logic functions are often faster and less expensive than the equivalent microprogram memory.

In 1947, the design of the MIT Whirlwind introduced the concept of a control store as a way to simplify computer design and move beyond ad hoc methods. The control store is a diode matrix: a two-dimensional lattice, where one dimension accepts "control time pulses" from the CPU's internal clock, and the other connects to control signals on gates and other circuits. A "pulse distributor" takes the pulses generated by the CPU clock and breaks them up into eight separate time pulses, each of which activates a different row of the lattice. When the row is activated, it activates the control signals connected to it.[11]

Described another way, the signals transmitted by the control store are being played much like a player piano roll. That is, they are controlled by a sequence of very wide words constructed of bits, and they are played sequentially. In a control store, however, the song is short and repeated continuously.

In 1951, Maurice Wilkes[12] enhanced this concept by adding conditional execution, a concept akin to a conditional in computer software. His initial implementation consisted of a pair of matrices: the first one generated signals in the manner of the Whirlwind control store, while the second matrix selected which row of signals (the microprogram instruction word, so to speak) to invoke on the next cycle. Conditionals were implemented by providing a way that a single line in the control store could choose from alternatives in the second matrix. This made the control signals conditional on the detected internal signal. Wilkes coined the term microprogramming to describe this feature and distinguish it from a simple control store.

• The EMIDEC 1100[13] reputedly uses a hard-wired control store consisting of wires threaded through ferrite cores, known as "the laces".
• Most models of the IBM System/360 series are microprogrammed:
  • The Model 25 is unique among System/360 models in using the top 16 K bytes of core storage to hold the control storage for the microprogram. The 2025 uses a 16-bit microarchitecture with seven control words (or microinstructions). After system maintenance or when changing operating mode, the microcode is loaded from the card reader, tape, or other device.[14] The IBM 1410 emulation for this model is loaded this way.
  • The Model 30 uses an 8-bit microarchitecture with only a few hardware registers; everything that the programmer saw is emulated by the microprogram. The microcode for this model is also held on special punched cards, which are stored inside the machine in a dedicated reader per card, called "CROS" units (Capacitor Read-Only Storage).[15]^: 2–5 Another CROS unit is added for machines ordered with 1401/1440/1460 emulation[15]^: 4–29 and for machines ordered with 1620 emulation.[15]^: 4–75
  • The Model 40 uses 56-bit control words. The 2040 box implements both the System/360 main processor and the multiplex channel (the I/O processor). This model uses TROS dedicated readers similar to CROS units, but with an inductive pickup (Transformer Read-only Store).
  • The Model 50 has two internal datapaths which operated in parallel: a 32-bit datapath used for arithmetic operations, and an 8-bit data path used in some logical operations. The control store uses 90-bit microinstructions.
  • The Model 85 has separate instruction fetch (I-unit) and execution (E-unit) to provide high performance. The I-unit is hardware controlled. The E-unit is microprogrammed; the control words are 108 bits wide on a basic 360/85 and wider if an emulator feature is installed.
• The NCR 315 is microprogrammed with hand wired ferrite cores (a ROM) pulsed by a sequencer with conditional execution. Wires routed through the cores are enabled for various data and logic elements in the processor.
• The Digital Equipment Corporation PDP-11 processors, with the exception of the PDP-11/20, are microprogrammed.[16]
• Most Data General Eclipse minicomputers are microprogrammed. The task of writing microcode for the Eclipse MV/8000 is detailed in the Pulitzer Prize-winning book titled The Soul of a New Machine.
• Many systems from Burroughs are microprogrammed:

• The B700 "microprocessor" execute application-level opcodes using sequences of 16-bit microinstructions stored in main memory; each of these is either a register-load operation or mapped to a single 56-bit "nanocode" instruction stored in read-only memory. This allows comparatively simple hardware to act either as a mainframe peripheral controller or to be packaged as a standalone computer.
• The B1700 is implemented with radically different hardware including bit-addressable main memory but has a similar multi-layer organisation. The operating system preloads the interpreter for whatever language is required. These interpreters present different virtual machines for COBOL, Fortran, etc.

• Microdata produced computers in which the microcode is accessible to the user; this allows the creation of custom assembler level instructions. Microdata's Reality operating system design makes extensive use of this capability.
• The Xerox Alto workstation used a microcoded design but, unlike many computers, the microcode engine is not hidden from the programmer in a layered design. Applications take advantage of this to accelerate performance.
• The IBM System/38 is described as having both horizontal and vertical microcode.[17] In practice, the processor implements an instruction set architecture named the Internal Microprogrammed Interface (IMPI) using a horizontal microcode format. The so-called vertical microcode layer implements the System/38's hardware-independent Machine Interface instruction set in terms of IMPI instructions. Prior to the instruction of the IBM RS64 processor line, early IBM AS/400 systems used the same architecture.[18]
• The Nintendo 64's Reality Coprocessor (RCP), which serves as the console's graphics processing unit and audio processor, utilizes microcode; it is possible to implement new effects or tweak the processor to achieve the desired output. Some notable examples of custom RCP microcode include the high-resolution graphics, particle engines, and unlimited draw distances found in Factor 5's Indiana Jones and the Infernal Machine, Star Wars: Rogue Squadron, and Star Wars: Battle for Naboo;[19][20] and the full motion video playback found in Angel Studios' Resident Evil 2.[21]

• The VU0 and VU1 vector units in the Sony PlayStation 2 are microprogrammable; in fact, VU1 is only accessible via microcode for the first several generations of the SDK.
• The MicroCore Labs MCL86 Archived 2016-11-03 at the Wayback Machine , MCL51 Archived 2017-02-02 at the Wayback Machine and MCL65 Archived 2018-12-21 at the Wayback Machine are examples of highly encoded "vertical" microsequencer implementations of the Intel 8086/8088, 8051, and MOS 6502.
• The Digital Scientific Corp. Meta 4 Series 16 computer system was a user-microprogammable system first available in 1970. The microcode had a primarily vertical style with 32-bit microinstructions.[22] The instructions were stored on replaceable program boards with a grid of bit positions. One (1) bits were represented by small metal squares that were sensed by amplifiers, zero (0) bits by the absence of the squares.[23] The system could be configured with up to 4K 16-bit words of microstore. One of Digital Scientific's products was an emulator for the IBM 1130.[24][25]
• The MCP-1600 is a microprocessor made by Western Digital in the late 1970s through the early 1980s used to implement three different computer architectures in microcode: the Pascal MicroEngine, the WD16, and the DEC LSI-11, a cost-reduced PDP-11.[26]
• Earlier x86 processors are fully microcoded; starting with the Intel 80486, less complicated instructions are implemented directly in hardware. x86 processors implemented patchable microcode (patch by BIOS or operating system) since Intel P6 microarchitecture and AMD K7 microarchitecture.
• Some video cards, wireless network interface controllers implemented patchable microcode (patch by operating system).

Each microinstruction in a microprogram provides the bits that control the functional elements that internally compose a CPU. The advantage over a hard-wired CPU is that internal CPU control becomes a specialized form of a computer program. Microcode thus transforms a complex electronic design challenge (the control of a CPU) into a less complex programming challenge. To take advantage of this, a CPU is divided into several parts:

• An I-unit may decode instructions in hardware and determine the microcode address for processing the instruction in parallel with the E-unit.
• A microsequencer picks the next word of the control store. A sequencer is mostly a counter, but usually also has some way to jump to a different part of the control store depending on some data, usually data from the instruction register and always some part of the control store. The simplest sequencer is just a register loaded from a few bits of the control store.
• A register set is a fast memory containing the data of the central processing unit. It may include the program counter and stack pointer, and may also include other registers that are not easily accessible to the application programmer. Often the register set is a triple-ported register file; that is, two registers can be read, and a third written at the same time.
• An arithmetic and logic unit performs calculations, usually addition, logical negation, a right shift, and logical AND. It often performs other functions, as well.

There may also be a memory address register and a memory data register, used to access the main computer storage. Together, these elements form an "execution unit". Most modern CPUs have several execution units. Even simple computers usually have one unit to read and write memory, and another to execute user code. These elements could often be brought together as a single chip. This chip comes in a fixed width that would form a "slice" through the execution unit. These are known as "bit slice" chips. The AMD Am2900 family is one of the best known examples of bit slice elements. The parts of the execution units and the whole execution units are interconnected by a bundle of wires called a bus.

Programmers develop microprograms, using basic software tools. A microassembler allows a programmer to define the table of bits symbolically. Because of its close relationship to the underlying architecture, "microcode has several properties that make it difficult to generate using a compiler."[2] A simulator program is intended to execute the bits in the same way as the electronics, and allows much more freedom to debug the microprogram. After the microprogram is finalized, and extensively tested, it is sometimes used as the input to a computer program that constructs logic to produce the same data. This program is similar to those used to optimize a programmable logic array. Even without fully optimal logic, heuristically optimized logic can vastly reduce the number of transistors from the number needed for a read-only memory (ROM) control store. This reduces the cost to produce, and the electricity used by, a CPU.

Microcode can be characterized as horizontal or vertical, referring primarily to whether each microinstruction controls CPU elements with little or no decoding (horizontal microcode)[lower-alpha 1] or requires extensive decoding by combinatorial logic before doing so (vertical microcode). Consequently, each horizontal microinstruction is wider (contains more bits) and occupies more storage space than a vertical microinstruction.

   # Any line starting with a number-sign is a comment
   # This is just a label, the ordinary way assemblers symbolically represent a 
   # memory address.
 InstructionJUMP:
       # To prepare for the next instruction, the instruction-decode microcode has already
       # moved the program counter to the memory address register. This instruction fetches
       # the target address of the jump instruction from the memory word following the
       # jump opcode, by copying from the memory data register to the memory address register.
       # This gives the memory system two clock ticks to fetch the next 
       # instruction to the memory data register for use by the instruction decode.
       # The sequencer instruction "next" means just add 1 to the control word address.
    MDR, NONE, MAR, COPY, NEXT, NONE
       # This places the address of the next instruction into the PC.
       # This gives the memory system a clock tick to finish the fetch started on the
       # previous microinstruction.
       # The sequencer instruction is to jump to the start of the instruction decode.
    MAR, 1, PC, ADD, JMP, InstructionDecode
       # The instruction decode is not shown, because it is usually a mess, very particular
       # to the exact processor being emulated. Even this example is simplified.
       # Many CPUs have several ways to calculate the address, rather than just fetching
       # it from the word following the op-code. Therefore, rather than just one
       # jump instruction, those CPUs have a family of related jump instructions.

A few computers were built using writable microcode. In this design, rather than storing the microcode in ROM or hard-wired logic, the microcode is stored in a RAM called a writable control store or WCS. Such a computer is sometimes called a writable instruction set computer (WISC).[32]

Many experimental prototype computers use writable control stores; there are also commercial machines that use writable microcode, such as the Burroughs Small Systems, early Xerox workstations, the DEC VAX 8800 (Nautilus) family, the Symbolics L- and G-machines, a number of IBM System/360 and System/370 implementations, some DEC PDP-10 machines,[33] and the Data General Eclipse MV/8000.[34]

Many more machines offer user-programmable writable control stores as an option, including the HP 2100, DEC PDP-11/60 and Varian Data Machines V-70 series minicomputers. The IBM System/370 includes a facility called Initial-Microprogram Load (IML or IMPL)[35] that can be invoked from the console, as part of power-on reset (POR) or from another processor in a tightly coupled multiprocessor complex.

Some commercial machines, for example IBM 360/85,[36][37] have both a read-only storage and a writable control store for microcode.

WCS offers several advantages including the ease of patching the microprogram and, for certain hardware generations, faster access than ROMs can provide. User-programmable WCS allows the user to optimize the machine for specific purposes.

Starting with the Pentium Pro in 1995, several x86 CPUs have writable Intel Microcode.[38][39] This, for example, has allowed bugs in the Intel Core 2 and Intel Xeon microcodes to be fixed by patching their microprograms, rather than requiring the entire chips to be replaced. A second prominent example is the set of microcode patches that Intel offered for some of their processor architectures of up to 10 years in age, in a bid to counter the security vulnerabilities discovered in their designs – Spectre and Meltdown – which went public at the start of 2018.[40][41] A microcode update can be installed by Linux,[42] FreeBSD,[43] Microsoft Windows,[44] or the motherboard BIOS.[45]

The design trend toward heavily microcoded processors with complex instructions began in the early 1960s and continued until roughly the mid-1980s. At that point the RISC design philosophy started becoming more prominent.

A CPU that uses microcode generally takes several clock cycles to execute a single instruction, one clock cycle for each step in the microprogram for that instruction. Some CISC processors include instructions that can take a very long time to execute. Such variations interfere with both interrupt latency and, what is far more important in modern systems, pipelining.

When designing a new processor, a hardwired control RISC has the following advantages over microcoded CISC:

• Programming has largely moved away from assembly level, so it's no longer worthwhile to provide complex instructions for productivity reasons.
• Simpler instruction sets allow direct execution by hardware, avoiding the performance penalty of microcoded execution.
• Analysis shows complex instructions are rarely used, hence the machine resources devoted to them are largely wasted.
• The machine resources devoted to rarely used complex instructions are better used for expediting performance of simpler, commonly used instructions.
• Complex microcoded instructions may require many clock cycles that vary, and are difficult to pipeline for increased performance.

There are counterpoints as well:

• The complex instructions in heavily microcoded implementations may not take much extra machine resources, except for microcode space. For example, the same ALU is often used to calculate an effective address and to compute the result from the operands, e.g., the original Z80, 8086, and others.
• The simpler non-RISC instructions (i.e., involving direct memory operands) are frequently used by modern compilers. Even immediate to stack (i.e., memory result) arithmetic operations are commonly employed. Although such memory operations, often with varying length encodings, are more difficult to pipeline, it is still fully feasible to do so - clearly exemplified by the i486, AMD K5, Cyrix 6x86, Motorola 68040, etc.
• Non-RISC instructions inherently perform more work per instruction (on average), and are also normally highly encoded, so they enable smaller overall size of the same program, and thus better use of limited cache memories.

Many RISC and VLIW processors are designed to execute every instruction (as long as it is in the cache) in a single cycle. This is very similar to the way CPUs with microcode execute one microinstruction per cycle. VLIW processors have instructions that behave similarly to very wide horizontal microcode, although typically without such fine-grained control over the hardware as provided by microcode. RISC instructions are sometimes similar to the narrow vertical microcode.

Microcode has been popular in application-specific processors such as network processors, microcontrollers, digital signal processors, channel controllers, disk controllers, network interface controllers, graphics processing units, and in other hardware.

Modern CISC implementations, such as the x86 family, decode instructions into dynamically buffered micro-operations ("μops") with an instruction encoding similar to RISC or traditional microcode. A hardwired instruction decode unit directly emits μops for common x86 instructions, but falls back to a more traditional microcode ROM containing μops for more complex or rarely used instructions.[3]

For example, an x86 might look up μops from microcode to handle complex multistep operations such as loop or string instructions, floating-point unit transcendental functions or unusual values such as denormal numbers, and special-purpose instructions such as CPUID.

• Smith, Richard E. (1988). "A Historical Overview of Computer Architecture". Annals of the History of Computing. 10 (4): 277–303. doi:10.1109/MAHC.1988.10039. S2CID 16405547. Retrieved June 21, 2006.
• Smotherman, Mark (2005). "A Brief History of Microprogramming". Retrieved July 30, 2006. {{cite journal}}: Cite journal requires |journal= (help)
• Wilkes, M.V. (1986). "The Genesis of Microprogramming". Annals of the History of Computing. 8 (2): 116–126. doi:10.1109/MAHC.1986.10035. S2CID 1978847. Retrieved August 7, 2006.
• Wilkes, M. V.; Stringer, J. B. (April 1953). "Microprogramming and the Design of the Control Circuits in an Electronic Digital Computer". Proceedings of the Cambridge Philosophical Society. 49 (pt. 2): 230–238. Bibcode:1953PCPS...49..230W. doi:10.1017/S0305004100028322. S2CID 62230627. Retrieved August 23, 2006.
• Husson, S.S. (1970). Microprogramming Principles and Practices. Prentice-Hall. ISBN 0-13-581454-5.
• Tucker, S.G. (1967). "Microprogram control for SYSTEM/360". IBM Systems Journal. 6 (4): 222–241. doi:10.1147/sj.64.0222.

Look up microcode in Wiktionary, the free dictionary.

• Writable Instruction Set Computer
• Capacitor Read-only Store
• Transformer Read-only Store
• A Brief History of Microprogramming
• Intel processor microcode security update (fixes the issues when running 32-bit virtual machines in PAE mode)
• Notes on Intel Microcode Updates, March 2013, by Ben Hawkes, archived from the original on September 7, 2015
• Hole seen in Intel's bug-busting feature, EE Times, 2002, by Alexander Wolfe, archived from the original on March 9, 2003
• Opteron Exposed: Reverse Engineering AMD K8 Microcode Updates, July 26, 2004
• WepSIM: An Online Interactive Educational Simulator Integrating Microdesign, Microprogramming, and Assembly Language Programming, July 26, 2022