Power loom

Shuttle with pirn

The main components of the loom are the warp beam, heddles, harnesses, shuttle, reed, and takeup roll. In the loom, yarn processing includes shedding, picking, battening and taking-up operations.

• Shedding. Shedding is the raising of the warp yarns to form a loop through which the filling yarn, carried by the shuttle, can be inserted. The shed is the vertical space between the raised and unraised warp yarns. On the modern loom, simple and intricate shedding operations are performed automatically by the heddle or heald frame, also known as a harness. This is a rectangular frame to which a series of wires, called heddles or healds, are attached. The yarns are passed through the eye holes of the heddles, which hang vertically from the harnesses. The weave pattern determines which harness controls which warp yarns, and the number of harnesses used depends on the complexity of the weave. Two common methods of controlling the heddles are dobbies and a Jacquard Head.
• Picking. As the harnesses raise the heddles or healds, which raise the warp yarns, the shed is created. The filling yarn is inserted through the shed by a small carrier device called a shuttle. The shuttle is normally pointed at each end to allow passage through the shed. In a traditional shuttle loom, the filling yarn is wound onto a quill, which in turn is mounted in the shuttle. The filling yarn emerges through a hole in the shuttle as it moves across the loom. A single crossing of the shuttle from one side of the loom to the other is known as a pick. As the shuttle moves back and forth across the shed, it weaves an edge, or selvage, on each side of the fabric to prevent the fabric from raveling.
• Battening. As the shuttle moves across the loom laying down the fill yarn, it also passes through openings in another frame called a reed (which resembles a comb). With each picking operation, the reed presses or battens each filling yarn against the portion of the fabric that has already been formed. The point where the fabric is formed is called the fell. Conventional shuttle looms can operate at speeds of about 150 to 200 picks per minute

With each weaving operation, the newly constructed fabric must be wound on a cloth beam. This process is called taking up. At the same time, the warp yarns must be let off or released from the warp beams. To become fully automatic, a loom needs a filling stop motion which will brake the loom, if the weft thread breaks.

Operation of weaving in a textile mill is undertaken by a specially trained operator known as a weaver. Weavers are expected to uphold high industry standards and are tasked with monitoring anywhere from ten to as many as thirty separate looms at any one time. During their operating shift, weavers will first utilize a wax pencil or crayon to sign their initials onto the cloth to mark a shift change, and then walk along the cloth side (front) of the looms they tend, gently touching the fabric as it comes from the reed. This is done to feel for any broken "picks" or filler thread. Should broken picks be detected, the weaver will disable the machine and undertake to correct the error, typically by replacing the bobbin of filler thread in as little time as possible. They are trained that, ideally, no machine should stop working for more than one minute, with faster turn around times being preferred.

Operation of this needs more than 2 people because of the way it works.

A loom from the 1890s with a dobby head. Illustration from the Textile Mercury.

The first ideas for an automatic loom were developed in 1784 by M. de Gennes in Paris and by Vaucanson in 1745, but these designs were never developed and were forgotten. In 1785 Edmund Cartwright patented a power loom. which used water power to speed up the weaving process, the predecessor to the modern power loom. His ideas were licensed first by Grimshaw of Manchester who built a small steam-powered weaving factory in Manchester in 1790, but the factory burnt down. Cartwright's was not a commercially successful machine; his looms had to be stopped to dress the warp. Over the next decades, Cartwright's ideas were modified into a reliable automatic loom.

These designs preceded John Kay's invention of the flying shuttle and they passed the shuttle through the shed using levers. With the increased speed of weaving, weavers were able to use more thread than spinners could produce.[1]

The development of the power loom in and around Manchester was not a coincidence. Manchester had been a centre for Fustians by 1620 and acted as a hub for other Lancashire towns, so developing a communication network with them. It was an established point of export using the meandering River Mersey, and by 1800 it had a thriving canal network, with links to the Ashton Canal, Rochdale Canal the Peak Forest Canal and Manchester Bolton & Bury Canal. The fustian trade gave the towns a skilled workforce that was used to the complicated Dutch looms, and was perhaps accustomed to industrial discipline. While Manchester became a spinning town, the towns around were weaving towns producing cloth by the putting out system. The business was dominated by a few families, who had the capital needed to invest in new mills and to buy hundreds of looms. Mills were built along the new canals, so immediately had access to their markets. Spinning developed first and, until 1830, the handloom was still more important economically than the power loom when the roles reversed.[4] Because of the economic growth of Manchester, a new industry of precision machine tool engineering was born and here were the skills needed to build the precision mechanisms of a loom.

Power looms reduced demand for skilled handweavers, initially causing reduced wages and unemployment. Protests followed their introduction. For example, in 1816 two thousand rioting Calton weavers tried to destroy power loom mills and stoned the workers.[8] In the longer term, by making cloth more affordable the power loom increased demand and stimulated exports, causing a growth in industrial employment, albeit low-paid.[9] The power loom also opened up opportunities for women mill workers.[10] A darker side of the power loom's impact was the growth of employment of children in power loom mills.[11]

When operated by a skilled and attentive weaver, looms are not dangerous by themselves. However, there are a number of inherent dangers in the machines, to which inattentive or poorly trained weavers can fall victim. The most obvious is the moving reed, the frames which hold the heddles and the "pinch" or "sand" roll utilized to keep the cloth tight as it passes over the front of the machine and onto the doff roll. The most common injury in weaving is pinched fingers from distracted or bored workers, though this is not the only such injury found. There are numerous accounts of weavers with long hair getting it tangled in the warp itself and having their scalp pulled away from the skull, or large chunks of hair pulled off.[12] As a result of this, it has become industry standard for companies to require weavers to either keep hair up and tied, or to keep their hair short so as not to allow it to become tangled. Also, due to possible pinch points on the front of machines, loose, baggy clothing is prohibited. In addition, there is a risk of the shuttle flying out of the loom at a high-speed (200+ mph/322 kmh) and striking a worker if the moving reed encounters a thread/yarn or other mechanical jam/error. One complication for weavers, in the terms of safety, is the loud nature in which weave mills operate (115dB+). Because of this, it is nearly impossible to hear a person calling for help when entangled. This has led OSHA to outline specific guidelines[13] for companies to mitigate the chances of such accidents occurring. However, even with such guidelines in place, injuries in textile production due to the machines themselves, are still commonplace.

• Dobby loom
• Jacquard loom
• Paul Moody
• James Henry Northrop
• Northrop Loom
• Textile Manufacturing - the Industrial Revolution
• Cotton - Spinning, Winding, Warping and Weaving

Media related to Power looms at Wikimedia Commons