Slope

In mathematics, the slope or gradient of a line is a number that describes both the direction and the steepness of the line.[1] Slope is often denoted by the letter m ; there is no clear answer to the question why the letter m is used for slope, but its earliest use in English appears in O'Brien (1844)[2] who wrote the equation of a straight line as "y = mx + b" and it can also be found in Todhunter (1888)[3] who wrote it as "y = mx + c".[4]

Slope:

m={\frac {\Delta y}{\Delta x}}=\tan(\theta )

Slope is calculated by finding the ratio of the "vertical change" to the "horizontal change" between (any) two distinct points on a line. Sometimes the ratio is expressed as a quotient ("rise over run"), giving the same number for every two distinct points on the same line. A line that is decreasing has a negative "rise". The line may be practical - as set by a road surveyor, or in a diagram that models a road or a roof either as a description or as a plan.

The steepness, incline, or grade of a line is measured by the absolute value of the slope. A slope with a greater absolute value indicates a steeper line. The direction of a line is either increasing, decreasing, horizontal or vertical.

A line is increasing if it goes up from left to right. The slope is positive, i.e. $m>0$ .
A line is decreasing if it goes down from left to right. The slope is negative, i.e. $m<0$ .
If a line is horizontal the slope is zero. This is a constant function.
If a line is vertical the slope is undefined (see below).

The rise of a road between two points is the difference between the altitude of the road at those two points, say y₁ and y₂, or in other words, the rise is (y₂ − y₁) = Δy. For relatively short distances, where the Earth's curvature may be neglected, the run is the difference in distance from a fixed point measured along a level, horizontal line, or in other words, the run is (x₂ − x₁) = Δx. Here the slope of the road between the two points is simply described as the ratio of the altitude change to the horizontal distance between any two points on the line.

In mathematical language, the slope m of the line is

m={\frac {y_{2}-y_{1}}{x_{2}-x_{1}}}.

The concept of slope applies directly to grades or gradients in geography and civil engineering. Through trigonometry, the slope m of a line is related to its angle of inclination θ by the tangent function

m=\tan(\theta )

Thus, a 45° rising line has a slope of +1 and a 45° falling line has a slope of −1.

As a generalization of this practical description, the mathematics of differential calculus defines the slope of a curve at a point as the slope of the tangent line at that point. When the curve is given by a series of points in a diagram or in a list of the coordinates of points, the slope may be calculated not at a point but between any two given points. When the curve is given as a continuous function, perhaps as an algebraic expression, then the differential calculus provides rules giving a formula for the slope of the curve at any point in the middle of the curve.

This generalization of the concept of slope allows very complex constructions to be planned and built that go well beyond static structures that are either horizontals or verticals, but can change in time, move in curves, and change depending on the rate of change of other factors. Thereby, the simple idea of slope becomes one of the main basis of the modern world in terms of both technology and the built environment.

Definition

Slope illustrated for y = (3/2)x − 1. Click on to enlarge

Slope of a line in coordinates system, from f(x)=-12x+2 to f(x)=12x+2

The slope of a line in the plane containing the x and y axes is generally represented by the letter m, and is defined as the change in the y coordinate divided by the corresponding change in the x coordinate, between two distinct points on the line. This is described by the following equation:

m={\frac {\Delta y}{\Delta x}}={\frac {{\text{vertical}}\,{\text{change}}}{{\text{horizontal}}\,{\text{change}}}}={\frac {\text{rise}}{\text{run}}}.

(The Greek letter delta, Δ, is commonly used in mathematics to mean "difference" or "change".)

Given two points $(x_{1},y_{1})$ and $(x_{2},y_{2})$ , the change in $x$ from one to the other is $x_{2}-x_{1}$ (run), while the change in $y$ is $y_{2}-y_{1}$ (rise). Substituting both quantities into the above equation generates the formula:

m={\frac {y_{2}-y_{1}}{x_{2}-x_{1}}}.

The formula fails for a vertical line, parallel to the $y$ axis (see Division by zero), where the slope can be taken as infinite, so the slope of a vertical line is considered undefined.

Examples

Suppose a line runs through two points: P = (1, 2) and Q = (13, 8). By dividing the difference in $y$ -coordinates by the difference in $x$ -coordinates, one can obtain the slope of the line:

m={\frac {\Delta y}{\Delta x}}={\frac {y_{2}-y_{1}}{x_{2}-x_{1}}}={\frac {8-2}{13-1}}={\frac {6}{12}}={\frac {1}{2}}

.

Since the slope is positive, the direction of the line is increasing. Since |m| < 1, the incline is not very steep (incline < 45°).

As another example, consider a line which runs through the points (4, 15) and (3, 21). Then, the slope of the line is

m={\frac {21-15}{3-4}}={\frac {6}{-1}}=-6.

Since the slope is negative, the direction of the line is decreasing. Since |m| > 1, this decline is fairly steep (decline > 45°).

Algebra and geometry

Slopes of parallel and perpendicular lines

If $y$ ' is a linear function of $x$ ', then the coefficient of $x$ is the slope of the line created by plotting the function. Therefore, if the equation of the line is given in the form
$y=mx+b$
then $m$ is the slope. This form of a line's equation is called the slope-intercept form, because $b$ can be interpreted as the y-intercept of the line, that is, the $y$ -coordinate where the line intersects the $y$ -axis.
If the slope $m$ of a line and a point $(x_{1},y_{1})$ on the line are both known, then the equation of the line can be found using the point-slope formula:
$y-y_{1}=m(x-x_{1}).$
The slope of the line defined by the linear equation
$ax+by+c=0$

is

$-{\frac {a}{b}}$ .
Two lines are parallel if and only if they are not the same line (coincident) and either their slopes are equal or they both are vertical and therefore both have undefined slopes. Two lines are perpendicular if the product of their slopes is −1 or one has a slope of 0 (a horizontal line) and the other has an undefined slope (a vertical line).
The angle θ between −90° and 90° that a line makes with the x-axis is related to the slope m as follows:
$m=\tan(\theta )$

and

$\theta =\arctan(m)$ (this is the inverse function of tangent; see inverse trigonometric functions).

Examples

For example, consider a line running through points (2,8) and (3,20). This line has a slope, $m$ , of

{\frac {(20-8)}{(3-2)}}\;=12.

One can then write the line's equation, in point-slope form:

y-8=12(x-2)=12x-24.

or:

y=12x-16.

The angle θ between −90° and 90° that this line makes with the $x$ -axis is

\theta =\arctan(12)\approx 85.2^{\circ }.

Consider the two lines: $y = -3 x + 1$ and $y = -3 x - 2$ . Both lines have slope $m = -3$ . They are not the same line. So they are parallel lines.

Consider the two lines $y = -3 x + 1$ and $y = .mw-parser-output .sfrac{white-space:nowrap}.mw-parser-output .sfrac.tion,.mw-parser-output .sfrac .tion{display:inline-block;vertical-align:-0.5em;font-size:85%;text-align:center}.mw-parser-output .sfrac .num,.mw-parser-output .sfrac .den{display:block;line-height:1em;margin:0 0.1em}.mw-parser-output .sfrac .den{border-top:1px solid}.mw-parser-output .sr-only{border:0;clip:rect(0,0,0,0);height:1px;margin:-1px;overflow:hidden;padding:0;position:absolute;width:1px}x/3 − 2$ . The slope of the first line is $m 1 = -3$ . The slope of the second line is $m 2 = 1 / 3$ . The product of these two slopes is −1. So these two lines are perpendicular.

Statistics

In statistics, the gradient of the least-squares regression best-fitting line for a given sample of data may be written as:

m={\frac {rs_{y}}{s_{x}}}

,

This quantity m is called as the regression slope for the line $y=mx+c$ . The quantity $r$ is Pearson's correlation coefficient, $s_{y}$ is the standard deviation of the y-values and $s_{x}$ is the standard deviation of the x-values. This may also be written as a ratio of covariances:[5]

m={\frac {\operatorname {cov} (Y,X)}{\operatorname {cov} (X,X)}}

Slope of a road or railway

There are two common ways to describe the steepness of a road or railroad. One is by the angle between 0° and 90° (in degrees), and the other is by the slope in a percentage. See also steep grade railway and rack railway.

The formulae for converting a slope given as a percentage into an angle in degrees and vice versa are:

{\text{angle}}=\arctan \left({\frac {\text{slope}}{100\%}}\right)

, (this is the inverse function of tangent; see trigonometry)

and

{\mbox{slope}}=100\%\times \tan({\mbox{angle}}),

where angle is in degrees and the trigonometric functions operate in degrees. For example, a slope of 100% or 1000‰ is an angle of 45°.

A third way is to give one unit of rise in say 10, 20, 50 or 100 horizontal units, e.g. 1:10. 1:20, 1:50 or 1:100 (or "1 in 10", "1 in 20", etc.) Note that 1:10 is steeper than 1:20. For example, steepness of 20% means 1:5 or an incline with angle 11.3°.

Roads and railways have both longitudinal slopes and cross slopes.

Slope warning sign in the Netherlands
Slope warning sign in Poland
A 1371-meter distance of a railroad with a 20‰ slope. Czech Republic
Steam-age railway gradient post indicating a slope in both directions at Meols railway station, United Kingdom

Calculus

At each point, the derivative is the slope of a line that is tangent to the curve at that point. Note: the derivative at point A is positive where green and dash-dot, negative where red and dashed, and zero where black and solid.

The concept of a slope is central to differential calculus. For non-linear functions, the rate of change varies along the curve. The derivative of the function at a point is the slope of the line tangent to the curve at the point, and is thus equal to the rate of change of the function at that point.

If we let Δx and Δy be the distances (along the x and y axes, respectively) between two points on a curve, then the slope given by the above definition,

m={\frac {\Delta y}{\Delta x}}

,

is the slope of a secant line to the curve. For a line, the secant between any two points is the line itself, but this is not the case for any other type of curve.

For example, the slope of the secant intersecting y = x² at (0,0) and (3,9) is 3. (The slope of the tangent at x = 3⁄2 is also 3 — a consequence of the mean value theorem.)

By moving the two points closer together so that Δy and Δx decrease, the secant line more closely approximates a tangent line to the curve, and as such the slope of the secant approaches that of the tangent. Using differential calculus, we can determine the limit, or the value that Δy/Δx approaches as Δy and Δx get closer to zero; it follows that this limit is the exact slope of the tangent. If y is dependent on x, then it is sufficient to take the limit where only Δx approaches zero. Therefore, the slope of the tangent is the limit of Δy/Δx as Δx approaches zero, or dy/dx. We call this limit the derivative.

{\frac {dy}{dx}}=\lim _{\Delta x\to 0}{\frac {\Delta y}{\Delta x}}

Its value at a point on the function gives us the slope of the tangent at that point. For example, let y = x². A point on this function is (−2,4). The derivative of this function is ^dy/_dx = 2x. So the slope of the line tangent to y at (−2,4) is 2 · (−2) = −4. The equation of this tangent line is: y−4 = (−4)(x − (−2)) or y = −4x − 4.

Difference of slopes

An extension of the idea of angle follows from the difference of slopes. Consider the shear mapping

(u,v)=(x,y){\begin{pmatrix}1&v\\0&1\end{pmatrix}}.

Then (1,0) is mapped to (1,v). The slope of (1,0) is zero and the slope of (1,v) is v. The shear mapping added a slope of v. For two points on {(1,y) : y in R} with slopes m and n, the image

(1,y){\begin{pmatrix}1&v\\0&1\end{pmatrix}}=(1,y+v)

has slope increased by v, but the difference n − m of slopes is the same before and after the shear. This invariance of slope differences makes slope an angular invariant measure, on a par with circular angle (invariant under rotation) and hyperbolic angle, with invariance group of squeeze mappings.[6][7]

References

Clapham, C.; Nicholson, J. (2009). "Oxford Concise Dictionary of Mathematics, Gradient" (PDF). Addison-Wesley. p. 348. Archived from the original (PDF) on 29 October 2013. Retrieved 1 September 2013.
O'Brien, M. (1844), A Treatise on Plane Co-Ordinate Geometry or the Application of the Method of Co-Ordinates in the Solution of Problems in Plane Geometry, Cambridge, England: Deightons
Todhunter, I. (1888), Treatise on Plane Co-Ordinate Geometry as Applied to the Straight Line and Conic Sections, London: Macmillan
Weisstein, Eric W. "Slope". MathWorld--A Wolfram Web Resource. Archived from the original on 6 December 2016. Retrieved 30 October 2016.
Further Mathematics Units 3&4 VCE (Revised). Cambridge Senior Mathematics. 2016. ISBN 9781316616222 – via Physical Copy.
Bolt, Michael; Ferdinands, Timothy; Kavlie, Landon (2009). "The most general planar transformations that map parabolas into parabolas". Involve: A Journal of Mathematics. 2 (1): 79–88. doi:10.2140/involve.2009.2.79. ISSN 1944-4176.
Abstract Algebra/Shear and Slope at Wikibooks

External links

"Slope of a Line (Coordinate Geometry)". Math Open Reference. 2009. Retrieved 30 October 2016. interactive

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.

[1] Clapham, C.; Nicholson, J. (2009). "Oxford Concise Dictionary of Mathematics, Gradient" (PDF). Addison-Wesley. p. 348. Archived from the original (PDF) on 29 October 2013. Retrieved 1 September 2013.

[2] O'Brien, M. (1844), A Treatise on Plane Co-Ordinate Geometry or the Application of the Method of Co-Ordinates in the Solution of Problems in Plane Geometry, Cambridge, England: Deightons

[3] Todhunter, I. (1888), Treatise on Plane Co-Ordinate Geometry as Applied to the Straight Line and Conic Sections, London: Macmillan

[4] Weisstein, Eric W. "Slope". MathWorld--A Wolfram Web Resource. Archived from the original on 6 December 2016. Retrieved 30 October 2016.

[5] Further Mathematics Units 3&4 VCE (Revised). Cambridge Senior Mathematics. 2016. ISBN 9781316616222 – via Physical Copy.

[6] Bolt, Michael; Ferdinands, Timothy; Kavlie, Landon (2009). "The most general planar transformations that map parabolas into parabolas". Involve: A Journal of Mathematics. 2 (1): 79–88. doi:10.2140/involve.2009.2.79. ISSN 1944-4176.

[7] Abstract Algebra/Shear and Slope at Wikibooks

Calculus
Precalculus	Binomial theorem Concave function Continuous function Factorial Finite difference Free variables and bound variables Graph of a function Linear function Radian Rolle's theorem Secant Slope Tangent
Limits	Indeterminate form Limit of a function One-sided limit Limit of a sequence Order of approximation (ε, δ)-definition of limit
Differential calculus	Derivative Second derivative Partial derivative Differential Differential operator Mean value theorem Notation Leibniz's notation Newton's notation Rules of differentiation linearity Power Sum Chain L'Hôpital's Product General Leibniz's rule Quotient Other techniques Implicit differentiation Inverse functions and differentiation Logarithmic derivative Related rates Stationary points First derivative test Second derivative test Extreme value theorem Maxima and minima Further applications Newton's method Taylor's theorem Differential equation Ordinary differential equation Partial differential equation Stochastic differential equation
Integral calculus	Antiderivative Arc length Riemann integral Basic properties Constant of integration Fundamental theorem of calculus Differentiating under the integral sign Integration by parts Integration by substitution trigonometric Euler Tangent half-angle substitution Partial fractions in integration Quadratic integral Trapezoidal rule Volumes Washer method Shell method Integral equation Integro-differential equation
Vector calculus	Derivatives Curl Directional derivative Divergence Gradient Laplacian Basic theorems Line integrals Green's Stokes' Gauss'
Multivariable calculus	Divergence theorem Geometric Hessian matrix Jacobian matrix and determinant Lagrange multiplier Line integral Matrix Multiple integral Partial derivative Surface integral Volume integral Advanced topics Differential forms Exterior derivative Generalized Stokes' theorem Tensor calculus
Sequences and series	Arithmetico-geometric sequence Types of series Alternating Binomial Fourier Geometric Harmonic Infinite Power Maclaurin Taylor Telescoping Tests of convergence Abel's Alternating series Cauchy condensation Direct comparison Dirichlet's Integral Limit comparison Ratio Root Term
Special functions and numbers	Bernoulli numbers e (mathematical constant) Exponential function Natural logarithm Stirling's approximation
History of calculus	Adequality Brook Taylor Colin Maclaurin Generality of algebra Gottfried Wilhelm Leibniz Infinitesimal Infinitesimal calculus Isaac Newton Fluxion Law of Continuity Leonhard Euler Method of Fluxions The Method of Mechanical Theorems
Lists	Differentiation rules List of integrals of exponential functions List of integrals of hyperbolic functions List of integrals of inverse hyperbolic functions List of integrals of inverse trigonometric functions List of integrals of irrational functions List of integrals of logarithmic functions List of integrals of rational functions List of integrals of trigonometric functions Secant Secant cubed List of limits Lists of integrals
Miscellaneous topics	Complex calculus Contour integral Differential geometry Manifold Curvature of curves of surfaces Tensor Euler–Maclaurin formula Gabriel's horn Integration Bee Proof that 22/7 exceeds π Regiomontanus' angle maximization problem Steinmetz solid