This article was co-authored by Alessandra Mendes. Alessandra Mendes is a Cleaning Specialist and the Founder of Cleaning Glow. With ten years of experience, Alessandra and her team specialize in providing residential cleaning services in the San Francisco Bay Area. All members of the Cleaning Glow team have completed thorough background checks.
wikiHow marks an article as reader-approved once it receives enough positive feedback. This article has 26 testimonials from our readers, earning it our reader-approved status.
This article has been viewed 764,885 times.
Gorilla glue is one of the most difficult glues to remove, as it cures quickly and strongly. Exfoliation and oil are the key to removing it once it dries, but it may not be 100% successful. Stronger gorilla glue products or glue that has had time to fully cure may need to be left to slough off on its own, but this should not cause harm as a one-time occurrence.
Steps
Removing Dry Gorilla Glue
-
1Exfoliate. Use a knife-sharpening stone, pumice stone, or other gritty or rough material to scrub your skin. Use a strong but slow motion to avoid tearing your skin, and alternate by rubbing with your fingers to prevent friction burns. Attempt this for several minutes, then move on if the glue shows no sign of balling up or peeling off.[1]
- If nothing else is available, use a scrap of wood or a thick index card.
-
2Apply oil. Rub one of the following oil-based materials onto your hands for several minutes:
- Hand lotion, olive oil, sunflower oil, or baby oil are all gentle on skin. Increase the effectiveness by heating it for about 10 seconds in the microwave, and/or by mixing in a pinch of salt to add friction.
- Lip gloss, lip balm, petroleum jelly (Vaseline), nonstick cooking spray, or oil-based makeup removers are additional options. Also Argan oil with raw Shea oil is a very good solvent.
- Polyglycol body lotion may be extra effective.[2]
Advertisement -
3Scrape with a blunt edge. Use a blunt butter knife or your fingernails to scrape away at the edge of the glue, while it is still oily. Avoid sharp blades, which may "succeed" by cutting off your protective outer layer of skin.
-
4Rub with citrus. Some people report success when rubbing slices of lemon or lime on the glue, or rubbing with a citrus oil or skin-safe citrus-based cleaner.[3]
- This method may sting if the gorilla glue or exfoliation has caused dry, cracked, or torn skin.
-
5Scrub with a homemade mixture. Wipe off your hand of the previous ointment, then track down the ingredients for a potentially more effective mixture. Industrial users of MDI, the bonding ingredient in Gorilla Glue, use the following mixture to clean up spills:
- Washing soda / soda ash (5 to 10%)
- Liquid detergent (0.2 to 2%)
- Water (add to reach 100%)
-
6Wait for a few days. The glue will wear off along with your regular skin replacement, with the stain fading completely in about four or five days. Waiting is recommended over using harsh chemicals, which are often ineffective and may damage skin.
- Keep your hands moisturized with lotion during this wait, as gorilla glue can cause dry or cracked skin.
Removing Tacky Gorilla Glue
-
1Wipe off tacky glue with a dry cloth. Wipe with a dry cloth or paper towel as soon as the glue spill occurs. If you catch it within a couple minutes, you may be able to remove all the glue.
-
2Wash with soap. Gorilla glue hardens when in contact with water, so this won't be 100% successful unless you catch the glue immediately. Wash with soap and plenty of water.[4]
- Bar soap will provide additional friction, but liquid soap may be more powerful. If using liquid soap, consider dish-washing soap instead of hand soap, unless you have sensitive skin.
- Try cleaning the area with hydrogen peroxide to break down the glue.
Warnings
- Alcohol, acetone, or other solvents are not recommended. These can remove your natural skin oils, which can increase the strength of the glue bond. Although soaking your hands in these solvents can be effective, repeated contact can cause skin or organ damage.⧼thumbs_response⧽
- Repeated gluing can wear through your hard outer layer of skin. This can result in increased sensitivity and pain from temperature and touch.⧼thumbs_response⧽
- Using baking soda and vinegar is not recommended, as it can finish the curing process and make the glue bond stronger.[5]⧼thumbs_response⧽
Things You'll Need
- Soap or detergent
- Baby oil or other skin-safe oil (polyglycol is best)
- Half of a lemon or lime
- Blunt butter knife
- Soda ash (washing soda)
References
- ↑ https://www.reference.com/home-garden/can-remove-dried-gorilla-glue-15dbb83aa26c4d16
- ↑ http://msdssearch.dow.com/PublishedLiteratureDOWCOM/dh_0342/0901b803803426eb.pdf?filepath=polyurethane/pdfs/noreg/109-01224.pdf&fromPage=GetDoc
- ↑ https://zukzik.com/how-to-get-gorilla-glue-off-skin/
- ↑ https://www.gorillatough.com/product/gorilla-super-glue/
- ↑ https://www.youtube.com/watch?v=ggekRdoQJNE
About This Article
To get dried Gorilla Glue off your hands, first try using a pumice stone or a knife-sharpening stone to scrub off the glue. If that doesn’t work, rub hand lotion, olive oil, or petroleum jelly onto your hands for several minutes. Then, use a butter knife or your fingernails to scrape off the glue. Alternatively, run slices of lemon or lime on the glue to see if that takes it off. For really stubborn glue, mix a solution that’s about 10% washing soda, 2% liquid detergent, and 88% water, and scrub your hands with it to remove the glue. For information on how to remove Gorilla Glue that’s still tacky, read on!
