How to Pull an Electric Meter

Last Updated: May 14, 2022 References

An electric meter (or "watt/hour" meter) is a device your local electric utility uses to measure the amount of power used in a building or home, for billing purposes. Normally, there is no need for anyone other than a qualified electrician or authorized utility employee to remove a meter. Furthermore, nearly all utilities require obtaining permission before breaking seals and removing meters. This wiki covers most typical (250V or less) residential meters, not those with bypass switches, multi-phase commercial / industrial meters or those part of current transformer cabinets, etc.

Steps

1
Locate the electric meter. Most times, it may usually be found on the outside of the home, but may also be found inside; near the electrical panel. If power is provided via aerial service lateral, simply following the wires to the home should make the meter visible.^{[1]
X
Research source}
2
Inspect the meter and meter enclosure. The meter is often held in position by one of several methods:^{[2]
X
Research source}
- A thin metal ring with a slot and tab. The ring has a shoulder along both sides of its length that engages the a lip on the edge of the meter and the rim of the meter socket or enclosure; and holds the meter securely into the socket. Once the ring's tab has been passed through the slot, a seal is placed on it to indicate tampering.
- A thick metal ring with a special locked enclosure around the retaining hardware, that prevents unauthorized persons from removing the ring and meter.
- The meter enclosure cover itself; which holds the lip of the meter and holds it in place in the meter enclosure. The cover will employ a simple seal or special locked enclosure over the retaining hardware that allows for the opening of the cover (and meter removal) similar to the previous two examples.
- Some other arrangement specific to the requirements of the local power company in your area. These types can not be covered by this wiki at this time.
Advertisement
3
Determine if you are able to remove the meter. Those meters secured with a simple seal - whether through a slot & tab on a thin metal ring around the meter or on the meter enclosure cover itself - will be the type that will allow removal of the meter. Those meters secured with thick rings / special locked enclosures, etc. will not be able to be removed without causing severe damage to the meter or enclosure and significant risk of shock, burns, fire or electrocution. This wiki is unable provide instructions to bypass this type of security hardware. The only safe remedy is to contact the local utility for removal.
4
Obtain permission from the local utility to break the seals and remove the meter. If the meter is secured with a simple seal and you have determined that you can remove it, notify the utility. This is often done by a phone call to their customer service department. You may be asked why you need to remove the meter, how long it is expected to be removed, etc. If you determine that you are unable to remove the meter, you can schedule to have an authorized employee to do this for you at this time.
5
Shut off power in the building. This will remove the load on the meter and will prevent destructive arcing and burning as the meter is withdrawn from the meter enclosure and when reinstalled, later. Note: switching circuit breakers to off and removing of fuses from the electrical panel will not remove power from the meter or enclosure.^{[3]
X
Research source}
- Switch ALL branch circuit breakers (typically all single and double pole types from 15 amps ~ 60 amps) handles to OFF, then locate the Service Disconnect Switch (the largest value circuit breaker) in the electrical panel; and move the handle to OFF, too.
- Remove fuses. Unscrew all fuses 2-3 full turns or more. Pull cartridge type fuses out completely and note the location of each for proper re-installation later.
6
Inspect the meter for indication of a connected load in the building. The meter should not be spinning, running or advancing at this point. If it is, there is still a panel connected somewhere. Check garages, out buildings, etc. and remove the load as described above. Ideally, the load should be fully disconnected before continuing. Keep in mind: Even though the meter isn't advancing because load has been shed; it does not mean the power is off! There is still electricity being provided by the utility, through the meter and into the electric panel - waiting to be used.
7
Cut and remove the seal. Use of a simple pair of wire cutters should be able to cut through the seal for removal. Watch out for sharp edges while removing the seal.
8
Place a rubber mat, sheet of plywood or other non-conductive material on the ground to stand on while working on the meter from this point. Do not stand on earth, concrete, vegetation, asphalt, etc. as these will conduct electricity.^{[4]
X
Research source}
9
Remove the retaining ring or cover that holds the meter in position. Lift the slot off the tab and spread the ring to remove it completely. The cover type will lift up or have screws to remove. If a lift type, push the meter upward slightly to allow the cover to clear the meter as it swings up. Be aware that behind the cover lies energized parts. Do not put your fingers where you cannot see them or behind the cover while removing it.
10
Rock the meter in an "up and down" motion to free the contact blades from the jaws. Do not use pressure near the base, nor reach behind the meter or into the enclosure - a steady up / down rocking while pulling will allow the meter to become free.^{[5]
X
Research source}
11
Once the meter is free, it should be secured from damage or theft. Since the meter is owned by the utility, you are liable for its loss. The meter enclosure should not be left unattended without first securing a reliable "dead front" to prevent accidental contact with live parts by people or other accidental conductors.^{[6]
X
Research source}
12
Reinstall. This is performed in the reverse order - except that the meter must be checked to be sure it is oriented right-side up; have its contact blades properly aligned with the enclosure's contact jaws and have steady pressure applied to its front while "rocking" in.

Community Q&A

Question

Is it true that the prongs that hold the meter in place remain energized, and touching them could be lethal?

Community Answer

Yes. On a residential 120/240v meter base (with meter removed), the top 2 are line side, and the bottom 2 are load side. A voltage test across the top 2 jaws will show 240v, and from neutral to each top jaw will show 120v. Consider all 4 jaws alive until proper voltage checks have been done.
Question

Can a power supplier enter a property and remove the meter without a warrant and/or permission of the property owner, can the power company leave the property without a power supply?

Community Answer

If the meter is inside a building, permission would be needed to enter. Many states have laws prohibiting disconnection of utilities from residences in some / all times of the year under certain circumstances (children or elderly residing in the home). Commercial and industrial type buildings would not likely be subject to this type of protection. Keep in mind that the meter itself is the property of the electric company; obtaining a warrant to retrieve it wouldn't likely be difficult. You'd do well to speak to your lawyer for precise advice.
Question

What if the glass comes out but not the meter itself?

Steve

Top Answerer

The utility should be notified at once of this problem. The glass serves as transparent insulation from the energized parts of the meter's measuring and indicating mechanisms. It protects people from shock and prevents rain and snow from entering that could result in fire or property loss.

Warnings

1. The potential risk of injury to property and person is significant; especially when this work is performed by unqualified persons. Most residential electrical systems in North America are 240VAC. Since as little as 50VAC under the right conditions can be lethal, emphasis on safety cannot be stressed enough.
2. The meter is property of the utility; not the homeowner, rate payer, etc., if you lose, damage or tamper with it, you may be required to pay for a replacement; and in the case of tampering to facilitate "theft of service" - subject to legal proceedings, jail and / or fine.
⧼thumbs_response⧽
Helpful 0 Not Helpful 0