Diving support vessel

The 2015 launched DSV Curtis Marshall

Gulmar Da Vinci in Albert Dock

The Skandi Arctic supply vessel in Leith docks

Most of the vessels currently in the North Sea have been built in the 1980s. The semi-submersible fleet, the Uncle John and similar, have proven to be too expensive to maintain and too slow to move between fields. Therefore, most existing designs are monohull vessels with either a one or a twin bell dive system. There has been little innovation since the 1980s. However, driven by high oil prices since 2004, the market for subsea developments in the North Sea has grown significantly. This has led to a scarcity of diving support vessels and has driven the price up. Thus, contractors have ordered a number of newbuild vessels which are expected to enter the market in 2008.

More recent vessels are designed and built to support both diving activities and remotely operated vehicles (ROVs) operations with dedicated hangar and LARS for ROV's, and to support seismic survey operations and cable-laying operations. They may have carry 80 to 150 project personnel on board, including divers, diving supervisors and superintendents, dive technicians, life support technicians and supervisors, ROV pilots, ROV superintendents, survey team, clients personnel, etc. For all these personnel to carry out their contracted job with an oil and gas company, a professional crew navigate and operate the vessel according to the contract requirements and instructions of project superintendents. However, ultimate responsibility lies on the master of the vessel for the safety of every person on board. In expanding the utility of the vessel, these vessels provide in addition to the usual domestic facilities. specialised diving mixed gas compressors and reclaim systems, gas storage and blending facilities, and saturation diving accommodation systems where the divers live under compression. These vessels are available to be hired by diving contractors or directly by oil and gas contractors who then will subcontract a specialist service-provider to use the vessel as a platform to carry out their activities.

Dynamic positioning (DP) is a computer-controlled system to automatically maintain a vessel's position and heading by using its own propellers and thrusters. Position reference sensors, combined with wind sensors, motion sensors and gyrocompasses, provide information to the computer pertaining to the vessel's position and the magnitude and direction of environmental forces affecting its position. Dynamic positioning is a great advantage for saturation diving operations as the risk to the divers and the work area from anchor patterns is reduced, and the vessel can be positioned more quickly.

The "saturation system", "saturation complex" or "saturation spread" typically comprises a surface complex made up of a living chamber, transfer chamber and submersible decompression chamber,[3] which is commonly referred to in commercial diving and military diving as the diving bell,[4] PTC (personnel transfer capsule) or SDC (submersible decompression chamber).[1] The system can be permanently installed on the ship or can be capable of being moved from one vessel to another by crane. The entire system is managed from a control room ("van"), where depth, chamber atmosphere and other system parameters are monitored and controlled. The diving bell is the elevator or lift that transfers divers from the system to the work site. Typically, it is mated to the system utilizing a removable clamp and is separated from the system tankage bulkhead by a trunking space, a kind of tunnel, through which the divers transfer to and from the bell. At the completion of work or a mission, the saturation diving team is decompressed gradually back to atmospheric pressure by the slow venting of system pressure, at an average of 15 metres (49 ft) to 30 metres (98 ft) per day (schedules vary). The process involves only one decompression, thereby avoiding the time-consuming and comparatively risky process of in-water, staged decompression or sur-D O₂ operations normally associated with non-saturation mixed gas diving.[5] More than one living chamber can be linked to the transfer chamber through trunking so that diving teams can be stored at different depths where this is a logistical requirement. An extra chamber can be fitted to transfer personnel into and out of the system while under pressure and to treat divers for decompression sickness if this should be necessary.[6]

The divers use surface supplied umbilical diving equipment, utilizing deep diving breathing gas, such as helium and oxygen mixtures, stored in large capacity, high pressure cylinders.[5] The gas supplies are plumbed to the control room, where they are routed to supply the system components. The bell is fed via a large, multi-part umbilical that supplies breathing gas, electricity, communications and hot water. The bell also is fitted with exterior mounted breathing gas cylinders for emergency use.[6]

While in the water the divers will often use a hot water suit to protect against the cold.[7] The hot water comes from boilers on the surface and is pumped down to the diver via the bell's umbilical and then through the diver's umbilical.[6]

The transfer chamber is where the bell is mated to the surface saturation system for transfer under pressure (TUP). It is a wet surface chamber where divers prepare for a dive and strip off and clean their gear after return. Connection to the bell may be overhead, through the bottom hatch of the bell, or lateral, through a side door.[6]

Accommodation chamber of a saturation spread

The accommodation chambers may be as small as 100 square feet.[8] This part is generally made of multiple compartments, including living, sanitation, and rest facilities, each a separate unit, joined by short lengths of cylindrical trunking. It is usually possible to isolate each compartment from the others using internal pressure doors.[6]

A closed diving bell, also known as personnel transfer capsule or submersible decompression chamber, is used to transport divers between the workplace and the accommodations chambers. The bell is a cylindrical or spherical pressure vessel with a hatch at the bottom, and may mate with the surface transfer chamber at the bottom hatch or at a side door. Bells are usually designed to carry two or three divers, one of whom, the bellman, stays inside the bell at the bottom and is stand-by diver to the working divers. Each diver is supplied by an umbilical from inside the bell. The bell has a set of high pressure gas storage cylinders mounted on the outside containing on-board reserve breathing gas. The on-board gas and main gas supply are distributed from the bell gas panel, which is controlled by the bellman. The bell may have viewports and external lights.[9] The divers' umbilicals are stored on racks inside the bell during transfer, and are tended by the bellman during the dive.[10]^: ch.13

The bell handling system lowers the diving bell of the US Navy's saturation fly-away diving system into the water.

The bell is deployed from a gantry or A-frame, also known as a bell launch and recovery system (LARS),[10]^: ch.13 on the vessel or platform, using a winch. Deployment may be over the side or through a moon pool.[9]

• The handling system must be able to support the dynamic loads imposed by operating in a range of weather conditions.
• It must be able to move the bell through the air/water interface (splash zone) in a controlled way, fast enough to avoid excessive movement caused by wave action.
• A bell cursor may be used to limit lateral motion through and above the splash zone.
• It must keep the bell clear of the vessel or platform to prevent impact damage or injury.
• It must have sufficient power for fast retrieval of the bell in an emergency, and fine control to facilitate mating of the bell and transfer flange, and to accurately place the bell at the bottom.
• It must include a system to move the bell between the mating flange of the transfer chamber and the launch/retrieval position.

Diving bells are deployed over the side of the vessel or platform using a gantry or A-frame from which the clump weight and the bell are suspended. On dive support vessels with in-built saturation systems the bell may be deployed through a moon pool. The bell handling system is also known as the launch and recovery system (LARS).[11] This is also used to move the bell from the position where it is locked on to the chamber system into the water, lower it to the working depth and hold it at that depth without excessive movement, for which heave compensation equipment may be fitted to the winch, and recover it to the chamber system. The system used to transfer the bell on deck may be a deck trolley system, an overhead gantry or a swinging A-frame. The system must constrain movement of the supported bell sufficiently to allow accurate location on the chamber trunking even in bad weather. A bell cursor may be used to control movement through and above the splash zone, and heave compensation gear may be used to limit vertical movement when in the water and clear of the cursor, particularly at working depth when the diver may be locked out and the bell is open to ambient pressure.[10] Cross-hauling gear may be useful to place the bell closer to the worksite if the ship cannot safely approach it to a convenient distance

A moon pool is an opening in the base of the hull, giving access to the water below, which allows divers, diving bells, remotely operated underwater vehicles or other equipment to enter or leave the water easily and in a relatively protected environment.

• Hazards of the positioning system
  • Anchor patterns
  • Thrusters

• On board recompression facilities
• Equipment to transport the diver through high risk zones
• Equipment to limit access to known hazards
• Hyperbaric evacuation facilities

• Use of stages and bells to transport the diver through the interface between air and water, to avoid hazards, and for decompression.
• Surface-supplied diving with limited umbilical length
• Underwater umbilical tending