Sulfuric acid

Although nearly 100% sulfuric acid solutions can be made, the subsequent loss of SO₃ at the boiling point brings the concentration to 98.3% acid. The 98.3% grade, which is more stable in storage, is the usual form of what is described as "concentrated sulfuric acid". Other concentrations are used for different purposes. Some common concentrations are:[13][14]

"Chamber acid" and "tower acid" were the two concentrations of sulfuric acid produced by the lead chamber process, chamber acid being the acid produced in the lead chamber itself (<70% to avoid contamination with nitrosylsulfuric acid) and tower acid being the acid recovered from the bottom of the Glover tower.[13][14] They are now obsolete as commercial concentrations of sulfuric acid, although they may be prepared in the laboratory from concentrated sulfuric acid if needed. In particular, "10 M" sulfuric acid (the modern equivalent of chamber acid, used in many titrations), is prepared by slowly adding 98% sulfuric acid to an equal volume of water, with good stirring: the temperature of the mixture can rise to 80 °C (176 °F) or higher.[14]

Sulfuric acid contains not only H₂SO₄ molecules, but is actually an equilibrium of many other chemical species, as it is shown in the table below.

Sulfuric acid is a colorless oily liquid, and has a vapor pressure of <0.001 mmHg at 25 °C and 1 mmHg at 145.8 °C,[16] and 98% sulfuric acid has a vapor pressure of <1 mmHg at 40 °C.[17]

In the solid state, sulfuric acid is a molecular solid that forms monoclinic crystals with nearly trigonal lattice parameters. The structure consists of layers parallel to the (010) plane, in which each molecule is connected by hydrogen bonds to two others.[3] Hydrates H₂SO₄·nH₂O are known for n = 1, 2, 3, 4, 6.5, and 8, although most intermediate hydrates are stable against disproportionation.[18]

Anhydrous H₂SO₄ is a very polar liquid, having a dielectric constant of around 100. It has a high electrical conductivity, a consequence of autoprotolysis, i.e. self-protonation :[15]

${\displaystyle {\ce {2 H2SO4 <=> H3SO4+ + HSO4-}}}$

The equilibrium constant for autoprotolysis ( (25 °C) is:[15]

[H₃SO₄]⁺[HSO₄]⁻ = 2.7 x 10^-4

The corresponding equilibrium constant for water, K_w is 10⁻¹⁴, a factor of 10¹⁰ (10 billion) smaller.

In spite of the viscosity of the acid, the effective conductivities of the H₃SO+4 and HSO−4 ions are high due to an intramolecular proton-switch mechanism (analogous to the Grotthuss mechanism in water), making sulfuric acid a good conductor of electricity. It is also an excellent solvent for many reactions.

Drops of concentrated sulfuric acid rapidly decompose a piece of cotton towel by dehydration.

The hydration reaction of sulfuric acid is highly exothermic, dilution.[19]

As indicated by its acid dissociation constant, sulfuric acid is a strong acid:

H₂SO₄ → H₃O⁺ + HSO−4 K_a1 = 1000

The product of this ionization is HSO−4, the bisulfate anion. Bisulfate is a far weaker acid:

HSO−4 + H₂O → H₃O⁺ + SO2−4 K_a2 = 0.01[20]

The product of this second dissociation is SO2−4, the sulfate anion.

Concentrated sulfuric acid has a powerful dehydrating property, removing water (H₂O) from other chemical compounds such as table sugar (sucrose) and other carbohydrates, to produce carbon, steam, and heat. Dehydration of table sugar (sucrose) is a common laboratory demonstration.[21] The sugar darkens as carbon is formed, and a rigid column of black, porous carbon called a carbon snake may emerge[22] as shown in the figure.

${\displaystyle {\underset {\text{sucrose}}{{\ce {C12H22O11}}}}\longrightarrow {\underset {{\text{black}} \atop {\text{graphitic foam}}}{{\ce {12 C}}}}+{\ce {11 H2O_{(g,l)}}}}$

Similarly, mixing starch into concentrated sulfuric acid gives elemental carbon and water. The effect of this can be seen when concentrated sulfuric acid is spilled on paper, which is composed of cellulose; the cellulose reacts to give a burnt appearance in which the carbon appears much like soot that results from fire. Although less dramatic, the action of the acid on cotton, even in diluted form, destroys the fabric.

${\displaystyle {\underset {\text{polysaccharide}}{{\ce {[C6H10O5]}}_{n}}}\longrightarrow 6n\ {\ce {C}}+5n\ {\ce {H2O}}}$

The reaction with copper(II) sulfate can also demonstrate the dehydration property of sulfuric acid. The blue crystals change into white powder as water is removed:

${\displaystyle {\underset {{\text{copper(II) sulfate}} \atop {\text{pentahydrate}}}{{\ce {CuSO4*5H2O}}}}\longrightarrow {\underset {{\text{anhydrous}} \atop {\text{copper(II) sulfate}}}{{\ce {CuSO4}}}}+{\ce {5 H2O}}}$

Sulfuric acid reacts with most bases to give the corresponding sulfate or bisulfate.

Sulfuric acid reacts with sodium chloride, and gives hydrogen chloride gas and sodium bisulfate:

NaCl + H₂SO₄ → NaHSO₄ + HCl

Aluminium sulfate, also known as paper maker's alum, aluminium sulfate is made by treating bauxite with sulfuric acid:

2 AlO(OH) + 3 H₂SO₄ → Al₂(SO₄)₃ + 4 H₂O

Sulfuric acid can also be used to displace weaker acids from their salts. Reaction with sodium acetate, for example, displaces acetic acid, CH₃COOH, and forms sodium bisulfate:

H₂SO₄ + CH₃CO₂Na → NaHSO₄ + CH₃COOH

Similarly, treating potassium nitrate with sulfuric acid produces nitric acid.

When combined with nitric acid, sulfuric acid acts both as an acid and a dehydrating agent, forming the nitronium ion NO+2, which is important in nitration reactions involving electrophilic aromatic substitution. This type of reaction, where protonation occurs on an oxygen atom, is important in many organic chemistry reactions, such as Fischer esterification and dehydration of alcohols.

Solid state structure of the [D₃SO₄]⁺ ion present in [D₃SO₄]⁺[SbF₆]⁻, synthesized by using DF in place of HF.

When allowed to react with superacids, sulfuric acid can act as a base and can be protonated, forming the [H₃SO₄]⁺ ion. Salts of [H₃SO₄]⁺ have been prepared (e.g. trihydroxyoxosulfonium hexafluoroantimonate(V) [H₃SO₄]⁺[SbF₆]⁻) using the following reaction in liquid HF:

[(CH₃)₃SiO]₂SO₂ + 3 HF + SbF₅ → [H₃SO₄]⁺[SbF₆]⁻ + 2 (CH₃)₃SiF

The above reaction is thermodynamically favored due to the high bond enthalpy of the Si–F bond in the side product. Protonation using simply fluoroantimonic acid, however, has met with failure, as pure sulfuric acid undergoes self-ionization to give [H₃O]⁺ ions:

2 H₂SO₄ ⇌ [H₃O]⁺ + [HS₂O₇]⁻

which prevents the conversion of H₂SO₄ to [H₃SO₄]⁺ by the HF/SbF₅ system.[23]

Even dilute sulfuric acid reacts with many metals via a single displacement reaction, like other typical acids, producing hydrogen gas and salts (the metal sulfate). It attacks reactive metals (metals at positions above copper in the reactivity series) such as iron, aluminium, zinc, manganese, magnesium, and nickel.

Fe + H₂SO₄ → H₂ + FeSO₄

Concentrated sulfuric acid can serve as an oxidizing agent, releasing sulfur dioxide:[7]

Cu + 2 H₂SO₄ → SO₂ + 2 H₂O + SO2−4 + Cu²⁺

Lead and tungsten, however, are resistant to sulfuric acid.

Hot concentrated sulfuric acid oxidizes carbon[24] (as bituminous coal) and sulfur:

C + 2 H₂SO₄ → CO₂ + 2 SO₂ + 2 H₂O

S + 2 H₂SO₄ → 3 SO₂ + 2 H₂O

Benzene undergoes electrophilic aromatic substitution with sulfuric acid to give the corresponding sulfonic acids:[25]

Sulfuric acid can be used to produce hydrogen from water:

2 I2 + 2 SO2 + 4 H2O → 4 HI + 2 H2SO4		(120 °C, Bunsen reaction)
2 H2SO4 → 2 SO2 + 2 H2O + O2		(830 °C)
4 HI → 2 I2 + 2 H2		(320 °C)

The compounds of sulfur and iodine are recovered and reused, hence the process is called the sulfur–iodine cycle. This process is endothermic and must occur at high temperatures, so energy in the form of heat has to be supplied. The sulfur–iodine cycle has been proposed as a way to supply hydrogen for a hydrogen-based economy. It is an alternative to electrolysis, and does not require hydrocarbons like current methods of steam reforming. But note that all of the available energy in the hydrogen so produced is supplied by the heat used to make it.[26][27]

In the stratosphere, the atmosphere's second layer that is generally between 10 and 50 km above Earth's surface, sulfuric acid is formed by the oxidation of volcanic sulfur dioxide by the hydroxyl radical:[29]

SO₂ + HO^• → HSO₃

HSO₃ + O₂ → SO₃ + HO₂

SO₃ + H₂O → H₂SO₄

Because sulfuric acid reaches supersaturation in the stratosphere, it can nucleate aerosol particles and provide a surface for aerosol growth via condensation and coagulation with other water-sulfuric acid aerosols. This results in the stratospheric aerosol layer.[29]

The permanent Venusian clouds produce a concentrated acid rain, as the clouds in the atmosphere of Earth produce water rain.[30] Jupiter's moon Europa is also thought to have an atmosphere containing sulfuric acid hydrates.[31]

In the first step, sulfur is burned to produce sulfur dioxide.

S(s) + O₂ → SO₂

The sulfur dioxide is oxidized to sulfur trioxide by oxygen in the presence of a vanadium(V) oxide catalyst. This reaction is reversible and the formation of the sulfur trioxide is exothermic.

2 SO₂ + O₂ ⇌ 2 SO₃

The sulfur trioxide is absorbed into 97–98% H₂SO₄ to form oleum (H₂S₂O₇), also known as fuming sulfuric acid or pyrosulphuric acid. The oleum is then diluted with water to form concentrated sulfuric acid.

H₂SO₄ + SO₃ → H₂S₂O₇

H₂S₂O₇ + H₂O → 2 H₂SO₄

Directly dissolving SO₃ in water, called the "wet sulfuric acid process", is rarely practiced because the reaction is extremely exothermic, resulting in a hot aerosol of sulfuric acid that requires condensation and separation.

In the first step, sulfur is burned to produce sulfur dioxide:

S + O₂ → SO₂ (−297 kJ/mol)

or, alternatively, hydrogen sulfide (H₂S) gas is incinerated to SO₂ gas:

2 H₂S + 3 O₂ → 2 H₂O + 2 SO₂ (−1036 kJ/mol)

The sulfur dioxide then oxidized to sulfur trioxide using oxygen with vanadium(V) oxide as catalyst.

2 SO₂ + O₂ ⇌ 2 SO₃ (−198 kJ/mol) (reaction is reversible)

The sulfur trioxide is hydrated into sulfuric acid H₂SO₄:

SO₃ + H₂O → H₂SO₄(g) (−101 kJ/mol)

The last step is the condensation of the sulfuric acid to liquid 97–98% H₂SO₄:

H₂SO₄(g) → H₂SO₄(l) (−69 kJ/mol)

A method that is the less well-known is the metabisulfite method, in which metabisulfite is placed at the bottom of a beaker and 12.6 molar concentration hydrochloric acid is added. The resulting gas is bubbled through nitric acid, which will release brown/red vapors of nitrogen dioxide as the reaction proceeds. The completion of the reaction is indicated by the ceasing of the fumes. This method does not produce an inseparable mist, which is quite convenient.

3 SO₂ + 2 HNO₃ + 2 H₂O → 3 H₂SO₄ + 2 NO

Burning sulfur together with saltpeter (potassium nitrate, KNO₃), in the presence of steam, has been used historically. As saltpeter decomposes, it oxidizes the sulfur to SO₃, which combines with water to produce sulfuric acid.

Alternatively, dissolving sulfur dioxide in an aqueous solution of an oxidizing metal salt such as copper(II) or iron(III) chloride:

2 FeCl₃ + 2 H₂O + SO₂ → 2 FeCl₂ + H₂SO₄ + 2 HCl

2 CuCl₂ + 2 H₂O + SO₂ → 2 CuCl + H₂SO₄ + 2 HCl

Two less well-known laboratory methods of producing sulfuric acid, albeit in dilute form and requiring some extra effort in purification. A solution of copper(II) sulfate can be electrolyzed with a copper cathode and platinum/graphite anode to give spongy copper at cathode and evolution of oxygen gas at the anode, the solution of dilute sulfuric acid indicates completion of the reaction when it turns from blue to clear (production of hydrogen at cathode is another sign):

2 CuSO₄ + 2 H₂O → 2 Cu + 2 H₂SO₄ + O₂

More costly, dangerous, and troublesome yet novel is the electrobromine method, which employs a mixture of sulfur, water, and hydrobromic acid as the electrolytic solution. The sulfur is pushed to bottom of container under the acid solution. Then the copper cathode and platinum/graphite anode are used with the cathode near the surface and the anode is positioned at the bottom of the electrolyte to apply the current. This may take longer and emits toxic bromine/sulfur bromide vapors, but the reactant acid is recyclable. Overall, only the sulfur and water are converted to sulfuric acid and hydrogen (omitting losses of acid as vapors):

2 HBr → H₂ + Br₂ (electrolysis of aqueous hydrogen bromide)

Br₂ + Br⁻ ↔ Br−3 (initial tribromide production, eventually reverses as Br⁻ depletes)

2 S + Br₂ → S₂Br₂ (bromine reacts with sulfur to form disulfur dibromide)

S₂Br₂ + 8 H₂O + 5 Br₂ → 2 H₂SO₄ + 12 HBr (oxidation and hydration of disulfur dibromide)

Prior to 1900, most sulfuric acid was manufactured by the lead chamber process.[32] As late as 1940, up to 50% of sulfuric acid manufactured in the United States was produced by chamber process plants.

In the early to mid 19th century "vitriol" plants existed, among other places, in Prestonpans in Scotland, Shropshire and the Lagan Valley in County Antrim Ireland, where it was used as a bleach for linen. Early bleaching of linen was done using lactic acid from sour milk but this was a slow process and the use of vitriol sped up the bleaching process.[33]

The dominant use for sulfuric acid is in the "wet method" for the production of phosphoric acid, used for manufacture of phosphate fertilizers. In this method, phosphate rock is used, and more than 100 million tonnes are processed annually. This raw material is shown below as fluorapatite, though the exact composition may vary. This is treated with 93% sulfuric acid to produce calcium sulfate, hydrogen fluoride (HF) and phosphoric acid. The HF is removed as hydrofluoric acid. The overall process can be represented as:

${\displaystyle {\underset {\text{fluorapatite}}{{\ce {Ca5(PO4)3F}}}}+{\ce {5 H2SO4 + 10 H2O}}\longrightarrow {\underset {{\text{calcium sulfate}} \atop {\text{dihydrate}}}{{\ce {5 CaSO4*2H2O}}}}+{\ce {HF + 3 H3PO4}}}$

Ammonium sulfate, an important nitrogen fertilizer, is most commonly produced as a byproduct from coking plants supplying the iron and steel making plants. Reacting the ammonia produced in the thermal decomposition of coal with waste sulfuric acid allows the ammonia to be crystallized out as a salt (often brown because of iron contamination) and sold into the agro-chemicals industry.

Sulfuric acid is also important in the manufacture of dyestuffs solutions.

Sulfuric acid is used in large quantities by the iron and steelmaking industry to remove oxidation, rust, and scaling from rolled sheet and billets prior to sale to the automobile and major appliances industry. Used acid is often recycled using a spent acid regeneration (SAR) plant. These plants combust spent acid with natural gas, refinery gas, fuel oil or other fuel sources. This combustion process produces gaseous sulfur dioxide (SO₂) and sulfur trioxide (SO₃) which are then used to manufacture "new" sulfuric acid. SAR plants are common additions to metal smelting plants, oil refineries, and other industries where sulfuric acid is consumed in bulk, as operating a SAR plant is much cheaper than the recurring costs of spent acid disposal and new acid purchases.

Hydrogen peroxide (H₂O₂) can be added to sulfuric acid to produce piranha solution, a powerful but very toxic cleaning solution with which substrate surfaces can be cleaned. Piranha solution is typically used in the microelectronics industry, and also in laboratory settings to clean glassware.

Sulfuric acid is used for a variety of other purposes in the chemical industry. For example, it is the usual acid catalyst for the conversion of cyclohexanone oxime to caprolactam, used for making nylon. It is used for making hydrochloric acid from salt via the Mannheim process. Much H₂SO₄ is used in petroleum refining, for example as a catalyst for the reaction of isobutane with isobutylene to give isooctane, a compound that raises the octane rating of gasoline (petrol). Sulfuric acid is also often used as a dehydrating or oxidizing agent in industrial reactions, such as the dehydration of various sugars to form solid carbon.

Domestic acidic drain cleaners usually contain sulfuric acid at a high concentration which turns a piece of pH paper red and chars it instantly, demonstrating both the strong acidic nature and dehydrating property.

Sulfuric acid acts as the electrolyte in lead–acid batteries (lead-acid accumulator):

At anode:

Pb + SO2−4 ⇌ PbSO₄ + 2 e⁻

At cathode:

PbO₂ + 4 H⁺ + SO2−4 + 2 e⁻ ⇌ PbSO₄ + 2 H₂O

Domestic acidic drain cleaners can be used to dissolve grease, hair and even tissue paper inside water pipes.

Overall:

Pb + PbO₂ + 4 H⁺ + 2 SO2−4 ⇌ 2 PbSO₄ + 2 H₂O

Sulfuric acid at high concentrations is frequently the major ingredient in domestic acidic drain cleaners[12] which are used to remove grease, hair, tissue paper, etc. Similar to their alkaline versions, such drain openers can dissolve fats and proteins via hydrolysis. Moreover, as concentrated sulfuric acid has a strong dehydrating property, it can remove tissue paper via dehydrating process as well. Since the acid may react with water vigorously, such acidic drain openers should be added slowly into the pipe to be cleaned.

The study of vitriols (hydrated sulfates of various metals forming glassy minerals from which sulfuric acid can be derived) began in ancient times. Sumerians had a list of types of vitriol that they classified according to the substances' color. Some of the earliest discussions on the origin and properties of vitriol is in the works of the Greek physician Dioscorides (first century AD) and the Roman naturalist Pliny the Elder (23–79 AD). Galen also discussed its medical use. Metallurgical uses for vitriolic substances were recorded in the Hellenistic alchemical works of Zosimos of Panopolis, in the treatise Phisica et Mystica, and the Leyden papyrus X.[36]

Medieval Islamic chemists like the authors writing under the name of Jabir ibn Hayyan (died c. 806 – c. 816 AD, known in Latin as Geber), Abu Bakr al-Razi (865 – 925 AD, known in Latin as Rhazes), Ibn Sina (980 – 1037 AD, known in Latin as Avicenna), and Muhammad ibn Ibrahim al-Watwat (1234 – 1318 AD) included vitriol in their mineral classification lists.[37]

The Jabirian authors and al-Razi experimented extensively with the distillation of various substances, including vitriols.[38] In one recipe recorded in his Kitāb al-Asrār ('Book of Secrets'), al-Razi may have created sulfuric acid without being aware of it:[39]

Take white (Yemeni) alum, dissolve it and purify it by filtration. Then distil (green?) vitriol with copper-green (the acetate), and mix (the distillate) with the filtered solution of the purified alum, afterwards let it solidify (or crystallise) in the glass beaker. You will get the best qalqadis (white alum) that may be had.[40]

— Abu Bakr al-Razi, Kitāb al-Asrār

In an anonymous Latin work variously attributed to Aristotle (under the title Liber Aristotilis, 'Book of Aristotle'),[41] to al-Razi (under the title Lumen luminum magnum, 'Great Light of Lights'), or to Ibn Sina,[42] the author speaks of an 'oil' (oleum) obtained through the distillation of iron(II) sulfate (green vitriol), which was likely 'oil of vitriol' or sulfuric acid.[43] The work refers multiple times to Jabir ibn Hayyan's Book of Seventy (Liber de septuaginta), one of the few Arabic Jabir works that were translated into Latin.[44] The author of the version attributed to al-Razi also refers to the Liber de septuaginta as his own work, showing that he erroneously believed the Liber de septuaginta to be a work by al-Razi.[45] There are several indications that the anonymous work was an original composition in Latin,[46] although according to one manuscript it was translated by a certain Raymond of Marseilles, meaning that it may also have been a translation from the Arabic.[47]

According to Ahmad Y. al-Hassan, three recipes for sulfuric acid occur in an anonymous Karshuni manuscript containing a compilation taken from several authors and dating from before c. 1100 AD.[48] One of them runs as follows:

The water of vitriol and sulphur which is used to irrigate the drugs: yellow vitriol three parts, yellow sulphur one part, grind them and distil them in the manner of rose-water.[49]

A recipe for the preparation of sulfuric acid is mentioned in Risālat Jaʿfar al-Sādiq fī ʿilm al-ṣanʿa, an Arabic treatise falsely attributed to the Shi'i Imam Ja'far al-Sadiq (died 765). Julius Ruska dated this treatise to the 13th century, but according to Ahmad Y. al-Hassan it likely dates from an earlier period:[50]

Then distil green vitriol in a cucurbit and alembic, using medium fire; take what you obtain from the distillate, and you will find it clear with a greenish tint.[51]

Sulfuric acid was called 'oil of vitriol' by medieval European alchemists because it was prepared by roasting iron(II) sulfate or green vitriol in an iron retort. The first allusions to it in works that are definitely European in origin appear in the thirteenth century AD, as for example in the works of Vincent of Beauvais, in the Compositum de Compositis ascribed to Albertus Magnus, and in pseudo-Geber's Summa perfectionis.[52]

In the seventeenth century, the German-Dutch chemist Johann Glauber prepared sulfuric acid by burning sulfur together with saltpeter (potassium nitrate, KNO₃), in the presence of steam. As saltpeter decomposes, it oxidizes the sulfur to SO₃, which combines with water to produce sulfuric acid. In 1736, Joshua Ward, a London pharmacist, used this method to begin the first large-scale production of sulfuric acid.

In 1746 in Birmingham, John Roebuck adapted this method to produce sulfuric acid in lead-lined chambers, which were stronger, less expensive, and could be made larger than the previously used glass containers. This process allowed the effective industrialization of sulfuric acid production. After several refinements, this method, called the lead chamber process or "chamber process", remained the standard for sulfuric acid production for almost two centuries.[4]

Sulfuric acid created by John Roebuck's process approached a 65% concentration. Later refinements to the lead chamber process by French chemist Joseph Louis Gay-Lussac and British chemist John Glover improved concentration to 78%. However, the manufacture of some dyes and other chemical processes require a more concentrated product. Throughout the 18th century, this could only be made by dry distilling minerals in a technique similar to the original alchemical processes. Pyrite (iron disulfide, FeS₂) was heated in air to yield iron(II) sulfate, FeSO₄, which was oxidized by further heating in air to form iron(III) sulfate, Fe₂(SO₄)₃, which, when heated to 480 °C, decomposed to iron(III) oxide and sulfur trioxide, which could be passed through water to yield sulfuric acid in any concentration. However, the expense of this process prevented the large-scale use of concentrated sulfuric acid.[4]

In 1831, British vinegar merchant Peregrine Phillips patented the contact process, which was a far more economical process for producing sulfur trioxide and concentrated sulfuric acid. Today, nearly all of the world's sulfuric acid is produced using this method.[53]

Drops of 98% sulfuric acid char a piece of tissue paper instantly. Carbon is left after the dehydration reaction staining the paper black.

Nitrile glove exposed to drops of 98% sulfuric acid for 10 minutes

Superficial chemical burn caused by two 98% sulfuric acid splashes (forearm skin)

Sulfuric acid is capable of causing very severe burns, especially when it is at high concentrations. In common with other corrosive acids and alkali, it readily decomposes proteins and lipids through amide and ester hydrolysis upon contact with living tissues, such as skin and flesh. In addition, it exhibits a strong dehydrating property on carbohydrates, liberating extra heat and causing secondary thermal burns.[7][8] Accordingly, it rapidly attacks the cornea and can induce permanent blindness if splashed onto eyes. If ingested, it damages internal organs irreversibly and may even be fatal.[6] Protective equipment should hence always be used when handling it. Moreover, its strong oxidizing property makes it highly corrosive to many metals and may extend its destruction on other materials.[7] Because of such reasons, damage posed by sulfuric acid is potentially more severe than that by other comparable strong acids, such as hydrochloric acid and nitric acid.

Sulfuric acid must be stored carefully in containers made of nonreactive material (such as glass). Solutions equal to or stronger than 1.5 M are labeled "CORROSIVE", while solutions greater than 0.5 M but less than 1.5 M are labeled "IRRITANT". However, even the normal laboratory "dilute" grade (approximately 1 M, 10%) will char paper if left in contact for a sufficient time.

The standard first aid treatment for acid spills on the skin is, as for other corrosive agents, irrigation with large quantities of water. Washing is continued for at least ten to fifteen minutes to cool the tissue surrounding the acid burn and to prevent secondary damage. Contaminated clothing is removed immediately and the underlying skin washed thoroughly.

Preparation of the diluted acid can be dangerous due to the heat released in the dilution process. To avoid splattering, the concentrated acid is usually added to water and not the other way around. A saying used to remember this is "Do like you oughta, add the acid to the water".[54] Water has a higher heat capacity than the acid, and so a vessel of cold water will absorb heat as acid is added.

Also, because the acid is denser than water, it sinks to the bottom. Heat is generated at the interface between acid and water, which is at the bottom of the vessel. Acid will not boil, because of its higher boiling point. Warm water near the interface rises due to convection, which cools the interface, and prevents boiling of either acid or water.

In contrast, addition of water to concentrated sulfuric acid results in a thin layer of water on top of the acid. Heat generated in this thin layer of water can boil, leading to the dispersal of a sulfuric acid aerosol or worse, an explosion.

Preparation of solutions greater than 6 M (35%) in concentration is dangerous, unless the acid is added slowly enough to allow the mixture sufficient time to cool. Otherwise, the heat produced may be sufficient to boil the mixture. Efficient mechanical stirring and external cooling (such as an ice bath) are essential.

Reaction rates double for about every 10-degree Celsius increase in temperature.[55] Therefore, the reaction will become more violent as dilution proceeds, unless the mixture is given time to cool. Adding acid to warm water will cause a violent reaction.

On a laboratory scale, sulfuric acid can be diluted by pouring concentrated acid onto crushed ice made from de-ionized water. The ice melts in an endothermic process while dissolving the acid. The amount of heat needed to melt the ice in this process is greater than the amount of heat evolved by dissolving the acid so the solution remains cold. After all the ice has melted, further dilution can take place using water.

Sulfuric acid is non-flammable.

The main occupational risks posed by this acid are skin contact leading to burns (see above) and the inhalation of aerosols. Exposure to aerosols at high concentrations leads to immediate and severe irritation of the eyes, respiratory tract and mucous membranes: this ceases rapidly after exposure, although there is a risk of subsequent pulmonary edema if tissue damage has been more severe. At lower concentrations, the most commonly reported symptom of chronic exposure to sulfuric acid aerosols is erosion of the teeth, found in virtually all studies: indications of possible chronic damage to the respiratory tract are inconclusive as of 1997. Repeated occupational exposure to sulfuric acid mists may increase the chance of lung cancer by up to 64 percent.[56] In the United States, the permissible exposure limit (PEL) for sulfuric acid is fixed at 1 mg/m³: limits in other countries are similar. There have been reports of sulfuric acid ingestion leading to vitamin B12 deficiency with subacute combined degeneration. The spinal cord is most often affected in such cases, but the optic nerves may show demyelination, loss of axons and gliosis.