Tempered glass is glass that has been heat-treated to make it harder, more resistant to heat, and break safely to prevent injury. The process is relatively straightforward, although it does require some specific equipment or facilities. Make sure to do all the cutting and shaping of the glass before you temper it, then heat it to the correct temperature and cool it right away to complete the process.

Part 1
Part 1 of 2:

Cutting and Shaping the Glass

  1. 1
    Cut the glass into the desired shape first. You have to cut and shape the glass before the glass is tempered. You will weaken or break the glass if you attempt to cut or reshape it in any way after tempering.[1]
    • Tempered glass is much harder than regular glass. However, if you cut, drill, or otherwise modify it after tempering, then it is highly likely that it will shatter into small pieces because it is more brittle than regular glass. Even if it doesn’t break, the glass will be compromised and will not be as strong as intended.

    Warning: Always wear safety glasses and a face mask that covers your mouth and nose when you are cutting and shaping glass to prevent you from breathing any glass dust in.

  2. 2
    Inspect the glass for imperfections like cracks and bubbles. Look closely to make sure that there are no cracks or other imperfections in the glass after you cut it to size. Such imperfections can make the glass break during tempering, so do not try to temper glass with any cracks or bubbles.[2]
    • It’s important to do this after cutting the glass, in case any cracks or other damages were caused while cutting the glass.
    Advertisement
  3. 3
    Sand the edges of the glass with wet sandpaper until they are smooth. Use a medium-coarse sandpaper like 80-grit sandpaper. Wet the sandpaper to keep glass dust from flying up in the air, and sand along the edges until the sharp edges are gone so that they aren’t dangerous.[3]
    • You can sand the edges by hand, with an electric sander, or with a rotary tool like a Dremel tool.
  4. 4
    Wash the glass to remove dust from sanding and any dirt. Small grains of glass and dirt can interfere with the tempering process. Make sure to wash the glass thoroughly to remove any traces of loose materials from it.[4]
    • You can just use regular, cool water. There is no need for any special cleaners.
  5. Advertisement
Part 2
Part 2 of 2:

Heating and Cooling the Glass

  1. 1
    Place the glass in a heated tempering oven or kiln with tongs or a paddle. The temperature needs to be at least 600 °C (1,112 °F) in order to temper the glass, so make sure the oven is at least this hot before you put the glass in. The industry standard for tempering glass is 620 °C (1,148 °F).[5]
    • You can use any type of oven or kiln to temper glass, as long as the temperatures can get high enough, although a tempering oven is ideal.
  2. 2
    Heat the glass for 2-25 minutes to temper it. Glass will take between 2 and 25 minutes to temper depending on the thickness, temperature of the oven, and other factors. Heat it for a full 25 minutes at above 600 °F (316 °C) to be sure you temper it.[6]
    • In a glass tempering facility, you will be able to be more precise with the times because of the special ovens they have. However, if you are tempering glass in less-scientific conditions, then you will have to experiment to learn exactly how long it takes to temper different thicknesses of glass in your oven or kiln.
  3. 3
    Remove the hot glass from the oven and set it on a brick or cement surface. Use tongs or a paddle made for handling hot glass. Remove it from the oven carefully and set it down on the surface to start the cooling process as quickly as possible.[7]
    • In facilities specially designed for tempering glass, there will be a special quenching oven that the glass gets transferred to after the oven.
  4. 4
    Quench the glass with blasts of cool air for 3-10 seconds to cool it. Immediately start blasting the glass with cool air from high-pressure nozzles at various angles after you remove it from the oven. This causes the outer surfaces of the glass to contract and compress against the center by cooling them faster, which is what makes the tempered glass strong.[8]
    • If you are tempering glass in a special facility with a quenching oven, the oven will have nozzles to blast cool air preset at different angles. If you are working with more limited resources, you can use a compressed air hose and move it constantly while blasting the glass to hit all the different angles.
    • Tempered glass is about 6 times stronger than regular glass. When it does break, it will break into small shards that are much safer than the jagged pieces that regular glass (called floating glass) breaks into.

    Tip: Tempered glass has to have a surface compression of 10,000 PSI or higher. It will typically break under about 24,000 PSI.

  5. 5
    Check the glass with polarized glasses and by shining a light through it. Properly tempered glass has shadow-like patterns that you will be able to see through polarized lenses. These patterns are called “quench marks”. Shine a light through the glass to make them easier to see.[9]
    • These quench marks can look like dark, shady spots or lines that stretch across the surface of the glass.
  6. Advertisement

Community Q&A

  • Question
    Can l drill a hole in tempered glass? If I do, what will happen?
    Matt Chase
    Matt Chase
    Community Answer
    Absolutely not. All holes, etching, sanding edges, and cutting must be done before tempering, otherwise the glass will break.
  • Question
    How do I turn regular glass into high-temperature-resistant glass?
    Community Answer
    Community Answer
    Melt the glass with up to 50% boric acid to make Pyrex. It will make it much more resistant to breaking from heat shock, and will lower its melting point.
  • Question
    When heating the glass, how does the glass need to be supported?
    Community Answer
    Community Answer
    The glass is supported by ceramic rollers in an oscillating heating chamber.
Advertisement

Warnings

  • Wear appropriate safety gear, including safety goggles and a face mask, whenever you are cutting and sanding glass.
    ⧼thumbs_response⧽
  • Use tongs or a paddle to put the glass into and remove it from the oven.
    ⧼thumbs_response⧽
Advertisement

About This Article

wikiHow Staff
Co-authored by:
wikiHow Staff Writer
This article was co-authored by wikiHow Staff. Our trained team of editors and researchers validate articles for accuracy and comprehensiveness. wikiHow's Content Management Team carefully monitors the work from our editorial staff to ensure that each article is backed by trusted research and meets our high quality standards. This article has been viewed 150,640 times.
26 votes - 96%
Co-authors: 11
Updated: May 9, 2022
Views: 150,640
Categories: Working with Glass
Advertisement