How to Cut Plexiglass

Co-authored by wikiHow Staff

Last Updated: May 11, 2022 Approved

Plexiglass is a cheap and durable material that you can use for a variety of projects like picture frames, tabletops, or as a shatterproof substitute for glass. It is lightweight, inexpensive, and it lasts for a long time because it can’t rot or crack. You can also easily cut it to shape with the right tools, the proper precautions, and correct measurements. Thin sheets can be scored and snapped with a utility knife or scoring tool. Thicker sheets will need to be cut with either a circular saw for straight lines or a jigsaw to cut shapes out of the sheet.

Method 1

Method 1 of 3:

Scoring and Snapping Thin Plexiglass

1
Lay the plexiglass flat on a work surface. For thin sheets of plexiglass that are up to ³⁄₁₆ inch (0.48 cm) thick, scoring the sheet and then snapping it is an easy way to cut it. Place the sheet down flat on a table or a work station so you can measure and cut on a stable surface.^{[1]
X
Research source}
- Make sure the surface is clean and clear of any objects that could impede your work or potentially mark or damage the sheet.
- Use an even and stable structure that doesn’t wobble.
2
Draw a line with a dry-erase marker where you want to cut the board. With the sheet laid flat on the work surface, use a ruler as a guide and draw a straight line where you want to cut the sheet. Make the line visible and be careful not to smudge the marker.^{[2]
X
Research source}
- Use a dry-erase marker so you can erase it after you cut the sheet.
Tip: If you make a mistake while you’re drawing the line, erase the mark fully so you can draw it again. Use a wet cloth or paper towel to remove the marker.

Advertisement
3
Use a utility knife to cut along the line you marked on the board. Make sure the sheet is flat and stable on the surface. Apply firm pressure and use a ruler to guide your utility knife as you drag it across the line you marked to score the sheet of plexiglass. Run the knife over the line 10 or 12 times, until you’ve made a deep groove in the sheet.^{[3]
X
Research source}
- You can also use a scoring tool to make your cuts if the blade is sharp enough to cut the plexiglass.
- The deeper you can make your cuts, the easier it will be to snap the board.
4
Flip the sheet over and score the other side. After you’ve formed a deep groove in 1 side of the plexiglass, grab the sheet by the sides and flip it over to expose the other side. Cut along the same line that you cut on the other side to further score the sheet. Score the plexiglass until you’ve formed a groove in the sheet.^{[4]
X
Research source}
- Be careful when you pick up the sheet so it doesn’t bend or warp before you’re ready to snap it.
5
Position the sheet so the portion that you cut is hanging over the edge. Once you’ve finished scoring the sheet, move it into a position that will make it easier for you to snap it off. Move the sheet so the portion that you plan to snap off is hanging over the edge.^{[5]
X
Research source}
- Be sure the entire portion that you plan to break off is hanging over the edge of the work surface.
6
Clamp the sheet in place to the surface. Use a spring or a C clamp and apply it to a part of the sheet that you don’t plan to cut. Apply the clamp so it’s attached to the sheet of plexiglass and the surface that you’re working on so the sheet doesn’t move.^{[6]
X
Research source}
- Be careful not to tighten the clamp so much that it puts a dent or divot in the sheet.
7
Snap off the cut portion of the plexiglass. With the sheet of plexiglass clamped in place on the work surface, apply quick, downward pressure to break off the piece that you cut. The sheet should break cleanly along the line that you scored in it.^{[7]
X
Research source}
- You can use 1 hand to brace the sheet while you push down on the sheet with the other hand.
- If the sheet doesn’t fully break along the line, use your utility knife to cut along the groove and break off the piece.

Method 2

Method 2 of 3:

Cutting Straight Lines with a Circular Saw

1
Use a circular saw with a carbide-tipped metal-cutting blade. Thicker sheets of plexiglass will need to be cut with a saw. Make sure the teeth of the blade are evenly spaced and the same size and shape for an even cut. A carbide-tipped blade that’s designed for cutting metal is strong enough to cut the sheet without any dust or debris flying off into the air.
- The fewer number of teeth on the blade will minimize the amount of dust or debris that cutting the plexiglass will produce.
- There are blades specially designed for cutting plexiglass that you can use as well.
Warning: Small particles of plexiglass could damage your eyes. Wear eye protection when you cut the sheet.
2
Set the sheet down on a sawhorse mark where you want to cut. Place the sheet of plexiglass on a sawhorse so you can cut through the sheet while keeping it flat and secure. Use a straight edge or a ruler to mark a straight line on the sheet of plexiglass. This line will be your cutting guide so make sure it is straight and visible.^{[8]
X
Research source}
- Use a dry-erase marker so you can easily erase the markings if you need to make adjustments.
3
Align the cutting guide of the saw with the line you marked. The circular saw will have a viewer or a slot that allows you to see where the saw is lined up. Put this guide in line with the marking that you put on the sheet of plexiglass.
- Make sure the sheet is secure and doesn’t shake or move.
4
Bring the saw to full speed before cutting the sheet. The blade of the saw must be rotating at full speed before it makes contact with the sheet to create a smooth and even cut. Turn on the saw and allow it to rotate until it gets to its full speed.
- Cutting the sheet before the saw has reached full speed could cause the teeth of the blade to snag on the sheet and create a jagged or choppy cut.
5
Push the saw slowly and smoothly through the plexiglass sheet. Use the cutting guide and the straight line to guide the saw through the sheet. Push the saw at a steady and consistent pace to prevent the saw from jamming.^{[9]
X
Research source}
- If the saw is stuttering or catching, you may be pushing the saw too fast. Stop pushing to let the blade get back up to speed and then continue to push the blade through the sheet.
- Make sure the 2 halves are balanced on the sawhorse so they don’t fall to the ground when you finish cutting through the sheet.

Method 3

Method 3 of 3:

Using a Jigsaw to Cut Shapes

1
Use a jigsaw to make rounded cuts in the plexiglass. A jigsaw looks a lot like a bandsaw but it’s shorter and cuts in an up-and-down motion. You can use a jigsaw to make straight cuts as well as rounded cuts so it’s a good option if you need to cut a specific shape or a circular piece out of a sheet of plexiglass.^{[10]
X
Research source}
- Use an uncoated blade with fine teeth to cut plexiglass.
- Keep a few extra blades nearby in case you need to replace it while you’re cutting.
2
Place the sheet of plexiglass flat on a sawhorse. Use a sawhorse as a work station to hold the sheet while you cut through it. Lie the sheet so it’s secure and stable on the sawhorse.^{[11]
X
Research source}
- Check to make sure the sheet doesn’t slide or wobble before you cut it.
3
Mark the sheet with a dry-erase marker to guide the jigsaw. It’s very important to have a guide to follow when you’re using a jigsaw, especially if the shape you are cutting is round or irregular. A jigsaw allows you to create a specific shape, but you need to have a good marking to use as a guide. Use a dry-erase marker to create the outline of the shape you plan to cut.^{[12]
X
Research source}
- A dry-erase marker makes it easier for you to erase the mark when you’re done or if you need to alter it.
Tip: If you’re cutting a design or shape, use a stencil or a round object to help mark an even line.
4
Put on safety glasses to protect your eyes. Sawing a sheet of plexiglass can cause splinters and tiny particles to fly in the air. These could damage your eyes if they get in them. Before you begin sawing, put on a pair of safety glasses.
- Make sure the glasses fit securely on your head so they don’t fall off while you’re sawing!
5
Drill a hole to fit the jigsaw into the sheet. The jigsaw will need an opening to fit into the plexiglass sheet, so start by drilling a hole with a drill and masonry bit large enough to make a hole that the blade will fit through. If you plan to cut shape with twists and turns, drill holes through the sheet at the tightest corners of the shape. This will help the jigsaw blade turn when it gets to those turns.^{[13]
X
Research source}
- If the blade of the jigsaw isn’t able to take the turns easily, it could bend the blade or break it.
6
Insert the saw blade into the hole and bring the blade to full speed. Fit the blade of the jigsaw into the hole you made in the sheet and turn it on. A jigsaw blade moves slower than a band saw or a circular saw, so it must be brought to full speed before you start using it to cut.^{[14]
X
Research source}
- If the blade isn’t at full speed when it makes contact with the plexiglass, it could catch and bend or possibly break and damage your jigsaw.
- It’s possible the blade could snap and injure you, so use caution.
7
Push the jigsaw slowly to cut through the sheet. Apply steady pressure to keep the jigsaw from jumping off of the sheet. Follow your guide markings closely and slow down to take any turns. If you hear or feel the blade catching or stalling, slow down and back up to allow the blade to get back up to speed, then continue to push the saw through the plexiglass.^{[15]
X
Research source}

Expert Q&A

Question

What's the best way to clean plexiglass?

Claudia & Angelo Zimmermann
House Cleaning Professionals
Claudia and Angelo Zimmermann are the founders of Everneat, an Eco-Friendly Cleaning Service based in New York City and in Connecticut. They are also the founders of Clean Code, a DIY 100% natural cleaning product line.

Claudia & Angelo Zimmermann

House Cleaning Professionals

Expert Answer

Use a dry dust microfiber cloth to dust the surface very softly—this specialty cloth attracts dust like a magnet. Then, fold your glass microfiber cloth into 4, spray your glass cleaner directly to the surface, and wipe. Remove any marks or streaks with the dry side of your cloth.
Question

What is the easiest way to mold and shape plexiglass?

Community Answer

Cut plexiglass to shape (ie: for the backing on shaped puzzles) by using a Dremel tool with grinder blades. It literally melts the plastic instead of cutting it and prevents the risk of it splitting.
Question

I'm cutting 1/4" clear plexi; should I score it, or use a circular saw?

Community Answer

It would be much easier with a circular saw if you have one. Scoring clear plexi will take a longer amount of time and effort.