Many wristwatches come with ready adjustable wristbands that are made of leather or plastic with holes and clasps for easy adjustment of the size. However, many designer brand watches and metal watch bands require the removal of metal links to adjust the size down. This may seem like a difficult task at first, but you can do this yourself at home with a few simple tools. Taking the watch to a jeweler or repair place isn't necessary and will cost you money.

Part 1
Part 1 of 2:

Sizing Your Watch

  1. 1
    Put the watch on without adjusting it. You will need to note how big the watch is.[1]
    • If the watch is very loose, you will have to remove lots of links.
    • If the watch is just slightly loose and you aren't in danger of it falling off, you might consider leaving it as is unless it is bothersome.
    • If your watch is too small, you will have to buy extra links from the manufacturer to make the band larger.
  2. 2
    Find the clasp. Pinch the band evenly from the clasp until it is the proper size.[2]
    • Make sure you have an equal number of links on either side of the clasp that need to be removed.
    • This will make sure the watch itself stays centered on the wrist band.
    • Write down the number of links that need to be removed from either side of the clasp.
    Advertisement
  3. 3
    Get your tools assembled. There are several things you will need to adjust your watch band.[3]
    • You will need one or two push pins. You will use these to push the pins that hold the links together out of their holes.
    • Get a pair of needle nosed pliers to help you remove the pins.
    • You will need a small jewelry hammer.
    • Make sure you are working on a flat surface with good lighting. You will need to collect any pins you remove from the band.
  4. Advertisement
Part 2
Part 2 of 2:

Removing Links from the Wristband

  1. 1
    Lay the watch on its side on your flat surface. Be sure to leave about 12 centimeter (0.2 in) of space between the bottom of each removable link and the flat surface.[4]
    • Count up the number of links you will need to remove.
    • Find the pin holding the last link in place.
    • This is where you will remove the links.
  2. 2
    Get your pushpins. Use one of the pushpins to push out the pin holding the wristband link in place.[5]
    • Push the sharp end of the pushpin against the head of the link pin.
    • If it doesn't give, use your jewelry hammer to force the head of the pushpin into the hole for the link pin.
    • A small amount of the push pin should now be protruding from the other side of the link.
    • Use the hammer to drive the push pin in further to get more of the link pin out.
  3. 3
    Remove the pin with the pliers. You will have to pull forcefully to get the pin out.[6]
    • Once you have enough of the link pin out of the hole on the other side of the wrist band to grasp it with the pliers, you can use the pliers to get it out.
    • Grasp the end of the pin tightly with the needle nose pliers.
    • Pull it out.
    • The links you need from one side of the clasp should be removed now.
    • You need to repeat the process for the other side of the wrist band now.
  4. 4
    Detach the clasp from the section of removed links. You will need to do this to put it back onto your wristband.[7]
    • Detach it using the same method you did for the links.
    • There should be a pin holding the clasp onto the links. Remove it using the hammer, pushpins, and pliers.
    • You will now re-attach the clasp to the wristband.
  5. 5
    Attach the clasp back onto the wrist band. Line up the link on the clasp with the last link on one side of your wristband.[8]
    • You should see a clear hole where a pin should go to hold the clasp on.
    • Take one of the pins you removed and insert it into this hole.
    • It should go most of the way in on its own, except for the last little bit on the end.
    • Use the hammer to gently pound the pin into the hole the whole way.
    • Repeat this process on the other side of the clasp.
    • Your watch band is now adjusted and assembled.
  6. 6
    Try on the watch. It should now fit without being too big or too small.[9]
    • If you have over-adjusted the watch, try adding a link to each side of the watch band.
    • If you haven't taken enough links out, re-assess how many need to be removed for the watch band to be tight enough and comfortable.
    • Wear the watch for a few days to make sure its comfortable.
  7. Advertisement

Community Q&A

  • Question
    What about watches with an arrow? Which way do I go?
    Community Answer
    Community Answer
    Push the pin out in same direction that arrow points. Do the opposite when reassembling.
  • Question
    Can I add links to my watch? Because it's too tight.
    Community Answer
    Community Answer
    Yes, that is perfectly possible. You may need to buy them from the manufacturer if you do not have any extra links.
  • Question
    Where do I get the tools to do this?
    Community Answer
    Community Answer
    You can purchase kits online and at watch stores.
Advertisement

Things You'll Need

  • Push pins
  • Hammer
  • Needle nosed pliers
  • Watch with adjustable band

About This Article

Tested by:
wikiHow Video Team
wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 20 people, some anonymous, worked to edit and improve it over time. This article has been viewed 1,362,705 times.
40 votes - 50%
Co-authors: 20
Updated: September 20, 2022
Views: 1,362,705
Categories: Watches
Article SummaryX

To adjust your watch band, first put your watch on and squeeze the links together around the clasp to count how many links you need to remove. Then, take your watch off and lay it flat. Find the small opening on the side of the first link you want to remove. Slide a pushpin into the opening of that link until the pin holding the band in place sticks out of the other side. You may need to tap the back of the pushpin with a rubber mallet or small hammer. Grab the portion of the pin that’s sticking out with a pair of pliers and pull it out of the link to unlock that side of the band. Then, repeat the process on the next opening to unlock the link from the band entirely. Once you've removed enough links, slide the 2 open links together. Slide one of the pins you removed into the hole over the clasp where the 2 links meet. Push it back into place or tap the back with a rubber mallet to finish adjusting your watch band. For tips on getting the clasp back on your watch band, scroll down!

Did this summary help you?
Advertisement