Light up the night repurposing old tin cans. That summertime, rustic appeal will add warmth and a glow to any balmy summer evening. All you will need are tin cans (of any size), leaves to use as a pattern and a hammer and nails.

Part 2
Part 2 of 5:

Prepare Tin Can For Punching

Freezing the tin can first will prevent your tin from being deformed once you start hammering it.

  1. 1
    Fill the tin can up to 3/4 of its length with sand. This will prevent bulging of the tin can when frozen. (Water expands when it freezes.)
  2. 2
    Add water.
  3. 3
    Place the tin can inside the freezer.
  4. 4
    Wait until the water freezes. Then remove the tin from the freezer.
  5. Advertisement
Part 3
Part 3 of 5:

Adding the Leaf Design

  1. 1
    Choose a suitable leaf to place on tin can. Tape the leaf in place on the can. Check that you like the placement and size before you begin to hammer.
  2. 2
    Tap the first nail into the leaf, being careful not to rip or break the leaf. Consider hammering the first nail toward the top of the leaf to stabilize your design.
  3. 3
    Hammer the remaining nails around the perimeter of the leaf in order to create a pattern. Space the nail holes evenly so your design appears symmetrical.
  4. 4
    Remove the nails and pull or tear off the leaf to expose the design. You should be able to see the same leaf pattern now outlined in nail holes on the tin can.
  5. Advertisement
Part 4
Part 4 of 5:

Spray Painting the Tin Can

Spray paint the can after you’ve created the design, so that you don’t disturb the paint (painting beforehand may create a more rough exterior).

  1. 1
    Place the tin can in an open, covered area. Spray paint it the desired color.
  2. 2
    Allow the tin can to dry for up to 24 hours. However, most spray paints will dry within 3 hours if left in a cool, dry area.
  3. Advertisement
Part 5
Part 5 of 5:

Assembling the Lantern

  1. 1
    Fill the bottom of the can with sand. Fill it with about a ½ cup of sand, depending upon the can size.
  2. 2
    Place the votive in the middle of the can, resting on the sand.
  3. 3
    Light the votive. (Or, turn on battery operated votive.) This will light up the night.
  4. 4
    Finished.
  5. Advertisement

Community Q&A

  • Question
    Why do I need to freeze the can?
    Community Answer
    Community Answer
    This is needed so that the tin stays firm. The ice will help put nice indents in the tin. Otherwise, the tin will just bend and be flimsy.
  • Question
    When and how do I remove the frozen sand from the can?
    Enigma
    Enigma
    Community Answer
    Wait for the ice to melt, and you can then just pour the sand away.
  • Question
    If using in the garden, would it be worth trying to make a lid for it? Very keen to try this out, but unsure how to make a lid.
    Enigma
    Enigma
    Community Answer
    You shouldn't use a lid unless your votive us a battery-powered one. Placing a lid on the can will reduce the oxygen needed by the flame.
Advertisement

Things You'll Need

  • Tin cans
  • Large leaves for your pattern (green leaves are stronger, you'll need leaves that can handle hammering)

  • A bucket of sand to hold the candles in place
  • As many nails as possible and your hammer to create the pattern
  • Masking tape
  • Spray paint
  • Votive candles; consider using battery operated votive candles to reduce the risk of fire

About This Article

wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 21 people, some anonymous, worked to edit and improve it over time. This article has been viewed 132,033 times.
121 votes - 89%
Co-authors: 21
Updated: December 23, 2021
Views: 132,033
Advertisement