Using decals can be a fun way to express creativity and individuality, but they can also be tough to remove. When you’re ready to get rid of your old decal, you can remove it successfully without leaving any marks, scratches, or residue. Clean the area well before and after and remove the decal with heat and friction to have the best results.

Part 1
Part 1 of 3:

Leading Up to Removal

  1. 1
    Clean the decal and the surrounding area. Fill a small bucket with warm water and add a couple squirts of liquid dish detergent or laundry soap. Dunk a sponge in the bucket and rub the area well to ensure that no dirt or grime interfere with the decal’s ability to separate.[1]
  2. 2
    Rinse and dry the area. Pour some fresh, clean water over the area to remove any suds. With a clean microfiber cloth, thoroughly rub the decal and the area around it dry until there are no more traces of soap or water. You can also just let it air dry for several minutes if you’re willing to wait a while longer.
    Advertisement
  3. 3
    Start lightly picking at the weaker points of the decal. Take a good look at the sticker and try to figure out where its weaker spots are. If, for instance, one of the corners of the decal is already lifting up a little on its own, start pulling away at that corner.
  4. Advertisement
Part 2
Part 2 of 3:

Getting the Decal off

  1. 1
    Apply heat with a hair dryer to loosen the adhesive. Plug in your hair dryer and put it on the hot setting. Hold the hair dryer a couple of inches away from the decal and start by keeping it aimed at the center for a few seconds. Then, slowly move to the other parts of the decal.[2] Continue this for several seconds until the decal is warm to the touch.
  2. 2
    Use rubbing alcohol or WD-40 before you pull the decal. After you’ve put the hair dryer away, it may be a good idea to apply a safe oil or alcohol-based substance to further influence the decal’s edges. Gently rub the substance on the corners.
  3. 3
    Peel or scrape away the decal. Use your fingernail, a rubber spatula, or and angled old credit card to carefully peel or scrape away the decal. If there is a clear weak spot on your decal, make sure to start removal there.
    • Unless you’re using it to remove a decal from a window, don’t use a razor blade. When not used extremely carefully, a razor blade may create permanent scratches to your painted surfaces.[3]
  4. Advertisement
Part 3
Part 3 of 3:

Cleaning Up After the Decal

  1. 1
    Carefully use a glue removal product. There may be leftover glue residue that you’ll want to get rid of. You can go to any automotive parts supply store to purchase a remover product that will get the job done safely. Put a dab of the product on a microfiber cloth and rub it onto the residue. Let it sit for about one minute before wiping it off with soapy water. Repeat this process until the residue is gone.[4]
  2. 2
    Clean the area again. Again, use a little friction with a sponge and warm, soapy water to make sure any leftover dirt is removed from the surface.[5] Dry the area again with a microfiber cloth.
  3. 3
    Apply a fresh coat of polish and wax. Finally, buff the spot where the decal was with a polishing compound and a fresh coat of wax. You can find both of these products at an automotive parts supply store. This will help remove any remaining discoloration and also protect the area.
  4. Advertisement

Expert Q&A

  • Question
    How do you remove stubborn vinyl decals from a car window?
    Chad Zani
    Chad Zani
    Auto Detailing Expert
    Chad Zani is the Director of Franchising at Detail Garage, an automotive detailing company with locations around the U.S. and Sweden. Chad is based in the Los Angeles, California area and uses his passion for auto detailing to teach others how to do so as he grows his company nationwide.
    Chad Zani
    Auto Detailing Expert
    Expert Answer
    Use a razor to remove the decal. If there's glue residue leftover, grab a clean razor and scrape it off. A quick decal spray or glass cleaner can help with that, since they'll act as a lubricant for the razor.
  • Question
    How do I remove vinyl wall stickers in room? If I removed it, can I paste it again?
    Community Answer
    Community Answer
    Heat softens vinyl. Using a paint heat gun (carefully) held about 8-11 inches away on the low setting, let the decal come up to a warm-hot temp. Do not touch with bare fingers, use a small flat screwdriver or a flat wood stick to gently nudge an edge to see if it is soft enough to lift away from the wall on its own. Do not overheat the wall, as this can cause a fire. As for reusing the decals, I do not think you can.
Advertisement

Warnings

  • Don’t use a pressure washer to remove old decals. This can cause damage to many different types of surfaces.
    ⧼thumbs_response⧽
Advertisement

Things You'll Need

  • Liquid detergent
  • Small bucket
  • Water
  • Sponge
  • Hair Dryer
  • WD-40 or Rubbing alcohol
  • Credit card
  • Automotive glue removal
  • Clean microfiber cloths
  • Automotive wax

About This Article

Chad Zani
Co-authored by:
Auto Detailing Expert
This article was co-authored by Chad Zani. Chad Zani is the Director of Franchising at Detail Garage, an automotive detailing company with locations around the U.S. and Sweden. Chad is based in the Los Angeles, California area and uses his passion for auto detailing to teach others how to do so as he grows his company nationwide. This article has been viewed 125,801 times.
3 votes - 100%
Co-authors: 17
Updated: March 29, 2022
Views: 125,801
Article SummaryX

When you’re ready to get rid of your old decals, use heat to remove them without leaving any marks or residue. Before removing the decal, clean it and the surrounding area with some warm water and dish soap so no dirt interferes with the removal. After you clean and dry the area, find a corner that’s lifting on its own and start pulling away at it. If the decal doesn’t fully lift off, hold a hairdryer a few inches away from the decal and heat it until it’s warm to the touch. This will help loosen the adhesive. Next, apply some rubbing alcohol or WD-40 on corners of the decal to further loosen the edges. Use your fingernail or an old credit card to carefully lift and scrape the decal away. To learn how to clean the area once the decal is off, keep reading!

Did this summary help you?
Advertisement